Dishwasher door latch: test and replace
Lights come on but nothing starts, or the door will not stay shut? The latch and its switch are the usual cause, and they live at the top of the door.
- Difficulty
- Easy
- Time
- 20–45 min
- Typical part cost
- $20–$80Pro: $95–$250
- Tools
- 3See the list
Take out the screws on the inside of the door, ease the outer panel off, and swap one part held by screws or tabs.
What it does
What the door latch does
The latch sits at the top of the door. When you close the door, a strike on the tub opening catches it and presses one or two small switches.
Those switches tell the control the door is shut. The dishwasher will not fill, wash or heat with the door open.
Why it fails
The plastic catch cracks or wears, so the door will not stay latched.
The switch inside wears out and stops closing, so the dishwasher acts as if the door is open.
A door that has dropped on worn hinges or springs no longer lines up with the strike.
Symptoms
Signs of a bad door latch
Will not start, lights on
The control lights up but nothing happens when you press Start.
Full diagnosisDoor will not stay shut
The door does not click shut, or pops open.
Stops mid-cycle
A worn switch can drop out during the cycle, stopping the wash.
Full diagnosis
How to test it
Test the door latch before you buy
- Close the door firmly and listen for a click. Look at the strike on the tub opening for damage.
- Check nothing on the top rack sticks out and stops the door closing fully.
- Good
- It clicks shut and holds. If it still will not start, test the switch.
- Bad
- No click, a broken catch, or a damaged strike. Replace the latch.
- Switch off the breaker and reach the latch (steps 1 to 3 below).
- Pull the wires off the switch terminals, noting where each goes.
- Close the latch with a screwdriver as the strike would, and test across the switch. Then release it and test again.
A good latch switch typically reads
Near 0 Ω (beeps) when latched, OL when open
Typical range. Check your part label or manual for the exact spec. Some latches have two or three switches. Test each one against the wiring diagram on your dishwasher.
- Good
- Continuity when latched and none when open, on each switch. The latch is fine.
- Bad
- No continuity when latched on any switch. Replace the latch assembly.
Safety first
Before you touch anything
- 1
Breaker off
Switch off the dishwasher's breaker, or unplug it under the sink. The latch switches carry line voltage. If it is hardwired, check with a voltage tester that the power is off before you touch any wires.
- 2
Hold the outer panel
The outer panel can drop as the last screws come out. Hold it with one hand. Do not remove the hinge screws at the bottom of the door.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Non-contact voltage testerPen styleOn a hardwired dishwasher, confirms the power is really off before you touch any wires.Typically $15–$30Shop this tool
- Multi-bit screwdriverPhillips, flat, squareRemoves the door panel and latch screws.Typically $10–$25Shop this tool
- Torx driver bitsT15, T20, T25OptionalMany dishwasher doors use Torx screws.Typically $6–$15Shop this tool
- Digital multimeterΩ, V, µF, µATests the latch switch for continuity.Typically $25–$60Shop this tool
Step by step
How to replace the door latch
- 1
Switch off the power
Turn off the breaker, or unplug the dishwasher under the sink.
- 2
Open the door panel
Open the door. Remove the screws on the inside of the door that hold the outer panel. Leave the hinge screws at the bottom alone.
Close the door partway and ease the outer panel off. On some models the control panel along the top comes off separately and has a wire harness to unplug.
- 3
Unplug the latch
Photograph the wires on the latch, then pull them off, or unplug the latch's connector.
- 4
Swap the latch
Remove the screws, or release the locking tabs, that hold the latch in the door. Take it out and fit the new one in the same place.
Buy the part
Door latch and switch
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The latch listed for your dishwasher's model number.
- The same number of switches and the same connector.
- 5
Reconnect and close up
Reconnect the wires as in your photo. Refit the panel and its screws, checking no wire is pinched.
- 6
Test it
Switch the power on. Close the door until it clicks and start a cycle.
Buy the part
Get the right replacement
Buy the part
Door latch and switch
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The latch listed for your dishwasher's model number.
- The same number of switches and the same connector.
Know your limits
When to call a pro
Stop and call a pro if
- A new latch does not fix it. The wiring in the door hinge or the control board may be at fault.
- The door drops or slams open. The door springs or cables need attention.
- You find melted wires at the latch.
FAQ
Door latch and switch questions
Why will my dishwasher not start with the door closed?
The latch switch is the first suspect. Also check that a child lock or delay start is not set. See dishwasher won't start.
Can I adjust the latch instead of replacing it?
Sometimes. The catch can often be adjusted a little by hand. If it is worn or broken, or the switch tests bad, replace the latch.
Why does my dishwasher door not stay closed?
A broken catch, a damaged strike, or something on the top rack hitting the door. Check the rack first.
Related
Keep going
- SymptomDishwasher won't startNothing happens, or the lights come on but it will not run. Power, a child lock or delay start, and the door latch cause most of it. The control board is last.Open guide
- Dishwasher partControl boardThe control board runs every step of the cycle and powers the valve, pumps and heater. It fails less often than the parts around it. When it is the cause, swap it inside the door.Open guide
- Dishwasher partDoor gasketThe rubber gasket around the tub opening seals the door. Food on it or a tear in it lets water drip out the front. Clean it, and replace it if it is damaged.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
