Dishwasher control board replacement
The board is the last thing to blame. Check the power, the latch and the parts first. If it really is the board, the swap is plugs and screws inside the door.
- Difficulty
- Easy
- Time
- 30 min–1 hr
- Typical part cost
- $100–$300Pro: $180–$600
- Tools
- 3See the list
Door panel off, plugs off, board out. The hard part is being sure the board is really the problem.
What it does
What the control board does
The control board reads the buttons, the door latch and the sensors, and switches the inlet valve, the pumps and the heater on and off in order.
On many built-in dishwashers it sits inside the door, behind the control panel along the top edge. On some models it sits in the base, behind the kick plate. A parts diagram for your model shows where.
Why it fails
Moisture, heat and power surges damage the relays and components.
A shorted part, like a pump or a heater, can damage the relay that powers it.
Symptoms
Signs of a bad control board
Dead controls
No lights and no response, though the breaker is on.
Full diagnosisStops at random
It stops at different points in the cycle, or shows codes that do not match one part.
A good part never runs
The pump, valve or heater tests good but never gets power during the cycle.
Full diagnosis
How to test it
Test the control board before you buy
- Check the breaker, and the wall switch under the sink on dishwashers that have one.
- Turn the breaker off for a minute and back on to reset the control.
- Check that a child lock or delay start is not set.
- Test the door latch and any part an error code points to.
- Good
- One of those fixes it most of the time.
- Bad
- Power is there, the latch and parts test good, and nothing runs. The board is the likely cause.
Safety first
Before you touch anything
- 1
Breaker off
Switch off the breaker, or unplug the dishwasher under the sink, and wait a few minutes before you touch the board. If it is hardwired, check with a voltage tester that the power is off before you touch any wires.
- 2
Handle it by the edges
Touch bare metal first to drain static, and hold the new board by its edges.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Non-contact voltage testerPen styleOn a hardwired dishwasher, confirms the power is really off before you touch any wires.Typically $15–$30Shop this tool
- Multi-bit screwdriverPhillips, flat, squareRemoves the door panel and the board screws.Typically $10–$25Shop this tool
- Torx driver bitsT15, T20, T25OptionalMany dishwasher doors use Torx screws.Typically $6–$15Shop this tool
- Painter's tape and markerLabel each plug before you take it off.Typically $5–$12Shop this tool
Step by step
How to replace the control board
- 1
Switch off the power
Turn off the breaker, or unplug the dishwasher under the sink.
- 2
Open the door panel
Open the door and remove the screws on the inside of the door that hold the outer door and control panel. Leave the hinge screws at the bottom alone. Close the door partway and lift the panel off.
If your board is in the base instead, remove the kick plate to reach it.
- 3
Label and unplug
Photograph the board, put a tape label on each plug, and pull them off by their bodies.
- 4
Swap the board
Remove the screws or release the clips, take the old board out, and fit the new one the same way.
Buy the part
Control board
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part number on the old board's label, plus your dishwasher's model number.
- Whether you need the main control or the button panel. Some come as one piece.
- 5
Reconnect and test
Plug everything back in to match your labels. Refit the panel.
Switch on and run a short cycle. Some new boards need a setup step from their instructions.
Buy the part
Get the right replacement
Buy the part
Control board
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part number on the old board's label, plus your dishwasher's model number.
- Whether you need the main control or the button panel. Some come as one piece.
Know your limits
When to call a pro
Stop and call a pro if
- You are not sure the board is the problem. Live voltage tests on a board are a pro job.
- The new board shows the same fault. The wiring or another part is the cause.
- The board is burned. Have the wiring and the part on that circuit checked.
FAQ
Control board questions
How do I reset a dishwasher control board?
Turn off the breaker, or unplug it, for a minute, then turn it back on. Many models also have a cancel or reset button sequence in the manual.
Is a control board worth replacing?
On a newer dishwasher, often. On an older one it can cost close to half a new machine. The repair or replace calculator can help.
Can I return an electronic part I do not need?
Many parts sellers will not take back an electrical part once it has been installed. Check the return policy before you buy, and rule out the other parts first.
Related
Keep going
- SymptomDishwasher won't startNothing happens, or the lights come on but it will not run. Power, a child lock or delay start, and the door latch cause most of it. The control board is last.Open guide
- SymptomDishwasher won't fill with waterYou hear the cycle start but no water comes in. A closed shutoff, a stuck float, or a failed inlet valve causes most of it. The latch and the control come next.Open guide
- Dishwasher partDoor latch and switchThe door latch holds the door shut and closes a switch that lets the dishwasher run. A broken latch or a worn switch means it will not start. Test it and swap it from inside the door.Open guide
- Dishwasher partWater inlet valveThe inlet valve lets hot water into the dishwasher for each fill. A clogged screen or a dead coil means no fill. A leaking seal means water when it is off. Test it and swap it from the front.Open guide
- Dishwasher partHeating elementOn many dishwashers, a heating element in the tub floor heats the water and dries the dishes. A burned-out one leaves dishes wet and lukewarm. Test it with a meter and replace it from below.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
