In the works
Symptom checker
Tell us what it is doing
The guided checker is being built: pick an appliance, pick a symptom, answer a few yes or no questions, and the likely parts light up on the model. Until then, start from a symptom below.
- FurnaceFurnace clicks but won't igniteThe inducer runs and the gas valve clicks, but the burners never light. After a few tries the furnace locks out. The usual culprit is a cracked igniter.Open guide
- FurnaceFurnace lights, then shuts off after a few secondsThe burners light, then go out a few seconds later. The furnace waits, tries again, and eventually locks out. A dirty flame sensor is the usual cause, and cleaning it is a 15-minute job.Open guide
- FurnaceInducer runs but the furnace never tries to lightThe draft inducer starts and keeps running, but the igniter never glows. The board is waiting for the pressure switch to say the vent is clear. Check the vent pipes and the switch hose first.Open guide
- FurnaceFurnace blower won't turn onThe big fan that pushes warm air to your vents does not start. A humming motor that never spins points to the run capacitor. Silence points to the door switch, a fuse, the board or the motor.Open guide
- FurnaceFurnace blowing cold airThe vents blow, but the air is cool or room temperature. Often the thermostat fan is set to On. Otherwise the burners are not lighting, or are shutting down early.Open guide
- FurnaceFurnace short cyclingThe furnace starts, runs briefly, shuts off, and starts again before the house warms up. A clogged filter is the most common cause. A dirty flame sensor is next.Open guide
- FurnaceFurnace won't turn on at allNothing happens when the thermostat calls for heat. The cause is usually a switch, a breaker, the thermostat or a loose blower door. After that, look at the board fuse and the control board.Open guide
- FurnaceFurnace making loud or unusual noisesSqueals and grinding usually mean a worn motor or a loose blower wheel. Rattles mean something is loose. Humming points to a motor or capacitor. A boom at start-up is delayed ignition and needs a pro.Open guide
- FurnaceFurnace control board blinking an error codeThe light on the control board flashes a code when something fails. Count the flashes, match them to the chart inside the blower door, and write the code down before you reset anything.Open guide
- DryerDryer runs but won't heatThe drum tumbles but the air stays cold. On an electric dryer, start with the breaker and the thermal fuse. On a gas dryer, start with the gas shutoff and watch the igniter.Open guide
- DryerDryer won't startThe dryer is dead, the lights come on but the drum never turns, or it hums without starting. Start with the breaker and the door, then the thermal fuse, the door switch and the start switch.Open guide
- DryerDryer runs but won't tumbleThe dryer starts and the motor runs, but the drum stays still or barely moves. The usual cause is a broken drum belt, then the idler pulley that keeps it tight, then worn drum rollers.Open guide
- DryerDryer squealing, squeaking or thumpingA squeal or squeak usually comes from the idler pulley or a motor bearing. A rhythmic thump usually comes from worn drum rollers, drum glides or a damaged belt. A rattle or knock can be the blower wheel.Open guide
- DryerDryer takes too long to dryLoads need two cycles, or come out damp. On gas and electric dryers alike, the usual cause is restricted airflow: a clogged lint screen, a blocked vent or a crushed duct. Load size matters too.Open guide
- DryerDryer shuts off earlyThe cycle ends, or the dryer stops mid-cycle, and the clothes are still damp. On gas and electric dryers, the usual causes are a blocked vent making it overheat, a coated moisture sensor, or a door that will not stay shut.Open guide
- Water heaterWater heater not heating: no hot waterEvery hot tap runs cold. On an electric heater it is usually power, a tripped high-limit reset, an element or a thermostat. On a gas heater, start with the gas supply and the pilot.Open guide
- Water heaterWater heater not making enough hot waterThe shower starts hot and goes cold too soon, or the water is never more than warm. Check the temperature setting first, then the lower element and thermostat on electric units, the dip tube and sediment.Open guide
- Water heaterWater heater making water too hotHot water comes out hotter than it should. Check the setting and measure at a tap. If it stays too hot after you turn it down, a thermostat or gas control has likely failed.Open guide
- Water heaterWater heater leakingWater on the floor or dripping down the tank. Shut off the power or gas and the cold supply, dry everything, then trace the water to its source: a valve, a fitting, an element gasket, or the tank itself.Open guide
- Water heaterWater heater rumbling or poppingA rumbling, popping or crackling tank usually means sediment has built up on the bottom. On electric heaters, scale on the lower element can do it too. Flushing the tank is the usual fix.Open guide
- Water heaterWater heater pilot won't stay litThe pilot lights but goes out, or will not stay on after you follow the lighting instructions. The usual cause is the thermocouple. A dirty pilot, a clogged air intake or the gas control can do it too. Repairs are pro work.Open guide
- Water heaterElectric water heater keeps tripping the breakerElectric water heaters only. The water heater's breaker at the panel shuts off, by itself, again and again. A heating element shorted to the tank is one of the most common causes. Wiring, water on the wiring, or the breaker itself are the others.Open guide
- Water heaterWater heater smells like rotten eggsA rotten egg smell in the air near a gas appliance can mean a gas leak: leave now and call the gas utility from outside. Sulfur-smelling hot water is a different, harmless problem, usually bacteria reacting with the anode rod.Open guide