Dryer squealing or thumping
A dryer is mostly spinning parts, and each one has its own sound when it wears. Listen closely and the noise points you to the part.
Check these first
Five-minute checks, no tools
Check for loose items
Look through the drum for coins, keys, buttons or a stray shoe. Turn items with big buttons or zippers inside out. These clicks and clunks are not a broken part.
Make sure it is level
All four feet should rest firmly on the floor. Check side to side and front to back with a level, and adjust the feet as needed.
Run it empty for a minute
Run the dryer with nothing in it. If a thump or squeal is still there with an empty drum, the noise is coming from the dryer, not the load.
Listen as it stops
Open the door mid-cycle and listen. A noise that stops with the drum is the drum, belt or rollers. A rattle that carries on for a moment as things spin down points to the blower wheel.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Idler pulley
The usual source of a squeal or squeak. The pulley spins fast and its bearing wears. Left alone, a squeal can turn into a scraping or thumping sound.
Fix the idler30 min–1.5 hr$8–$30 - 2DIY fix
Drum support rollers
Worn rollers lose firm contact with the drum and thump, even with the drum empty. Replace them as a set, since they wear evenly.
Fix the rollers45 min–3 hr$15–$60 - 3DIY fix
Worn or damaged drum belt
A belt that is frayed, cracked or has a damaged spot can thump as it runs over the pulleys. Look for fraying or missing chunks while the dryer is open.
Fix the belt30 min–2 hr$10–$70 - 4DIY fix
Worn drum glides
The front of the drum rides on glides or pads. When they wear down, the drum thumps or scrapes, usually up near the door opening.
- 5DIY fix
Drive motor bearings
A squeal, buzz or grind that is there whenever the motor runs can be worn motor bearings. If it grinds, stop using the dryer until it is fixed.
Fix the motor1 hr–3 hr$60–$200 - 6DIY fix
Blower wheel
A rattle, knock or bang, often with a little delay as the dryer stops. A coin or button may be caught in the wheel, or the wheel itself is cracked or loose on the motor shaft.
Fix the blower45 min–2 hr$10–$60
What's happening
What your dryer is doing
The drum rides on rollers at the back and on glides or pads at the front, and a belt turns it. A spring-loaded idler pulley keeps that belt tight. All of these wear slowly with use.
Squealing or squeaking while the drum turns is most often the idler pulley, a small wheel that spins fast and wears. A squeal or grind that is there whenever the motor runs, even with the drum empty, can be worn motor bearings.
Thumping once per turn usually means a roller with a flat or worn spot, worn glides, or a damaged belt. If the dryer sat unused for a long time, a roller can take a flat spot that smooths out after a few loads.
A rattle, knock or bang can be a coin or button caught in the blower wheel, or a cracked or loose wheel. The blower keeps coasting for a moment after the dryer stops, so a noise that lingers after shutoff points there.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas near a gas dryer. Do not touch switches or light anything. Get everyone out and call your gas supplier from outside or a neighbor's phone.
- You smell burning rubber or see smoke. Unplug the dryer and do not use it until it is checked.
- The noise is a loud grinding or metal scraping. Stop using the dryer to avoid more damage.
- You are not comfortable taking the front or top panel off and lifting the drum out.
FAQ
Common questions
Is a squeaking dryer safe to use?
A light squeak is usually a worn idler or roller, and it gets worse over time rather than failing all at once. Fix it soon. A grinding or scraping sound is different: stop using the dryer, because a failing part can damage others.
Why does my dryer thump only after it has sat for a while?
A drum roller can develop a flat spot when the dryer sits unused. The thump often smooths out after the dryer runs for a while. If it does not go away after a few loads, the rollers are likely worn. See the drum support rollers guide.
Should I replace the rollers, idler and belt all at once?
Rollers wear evenly, so replace them as a set. Many people do the belt and idler at the same time, since getting to the rollers already means taking the belt off.
Related
Keep going
- SymptomDryer runs but won't tumbleThe dryer starts and the motor runs, but the drum stays still or barely moves. The usual cause is a broken drum belt, then the idler pulley that keeps it tight, then worn drum rollers.Open guide
- Dryer partIdler pulleyThe idler pulley is a small spring-loaded wheel that keeps the drum belt tight. When its bearing wears, it squeals. Gas and electric dryers both have one.Open guide
- Dryer partDrum support rollersDrum support rollers are small wheels the drum rides on. When they wear flat or their bearings dry out, the dryer thumps, rumbles or squeaks. Gas and electric dryers both have them.Open guide
- Dryer partDrum beltThe drum belt wraps around the drum and the motor pulley and turns the drum. When it breaks, the drum stops tumbling. Gas and electric dryers both have one, and the swap is the same on both.Open guide
- Dryer partBlower wheelThe blower wheel is the fan that pulls air through the drum and pushes it out the vent. A cracked, loose or lint-packed wheel means slow drying and odd noises. Gas and electric dryers both have one.Open guide