Dryer runs but the drum won't turn
You can hear the motor, but the clothes just sit there. Good news: this is usually the belt, and a belt is a cheap part.
Check these first
Five-minute checks, no tools
Turn the drum by hand
Unplug the dryer, open the door and turn the drum with your hand. A good belt gives steady drag. If the drum spins with almost no resistance, the belt is likely broken or off.
Listen for the motor
Plug back in and start a cycle with the door shut. A steady motor sound with a still drum points to the belt or idler. A hum with no motor running belongs on the won't start page.
Empty the drum
Take everything out and try again with an empty drum. That rules out something jammed in the drum.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Broken or slipped drum belt
The most common reason a drum will not turn. The motor runs, the drum spins freely by hand.
Fix the belt30 min–2 hr$10–$70 - 2DIY fix
Idler pulley
The belt is intact but loose, or keeps coming off. A seized idler bearing or a broken spring arm loses the belt's tension, so it slips on the motor pulley.
Fix the idler30 min–1.5 hr$8–$30 - 3DIY fix
Worn drum support rollers
The drum is hard to turn by hand or wobbles once the belt is off. Worn rollers drag on the drum, and the extra load can make the belt slip or snap.
Fix the rollers45 min–3 hr$15–$60 - 4DIY fix
Drive motor
The belt and drum check out, but the motor hums and its pulley will not turn, or it stalls under load. The motor's start switch or winding has likely failed.
Fix the motor1 hr–3 hr$60–$200
What's happening
What your dryer is doing
One motor does two jobs. One end of its shaft turns a long, thin belt wrapped around the drum. The other end spins the blower wheel. A spring-loaded idler pulley keeps the belt tight.
If the motor runs but the drum stays still, the link between them is broken. Most often the belt has snapped or slipped off.
The belt can also come off because the idler pulley seized or its spring broke, or the drum can drag because its support rollers are worn. That is why repairers often look at the belt, idler and rollers together.
Two related cases: on some dryers a broken belt trips a switch and the dryer will not start at all, and a motor that only hums is not running properly. For either, see dryer won't start.
Know your limits
When to call a pro
Stop and call a pro if
- You smell burning or see smoke from the dryer. Unplug it and do not use it until it is checked.
- The motor hums but will not turn even with the belt off.
- The new belt keeps coming off or wearing out quickly.
- You are not comfortable taking the front or top panel off and lifting the drum out.
FAQ
Common questions
How can I tell if my dryer belt is broken?
Unplug the dryer, open the door and turn the drum by hand. With a good belt you feel steady resistance, because you are also turning the motor. If the drum spins easily and keeps coasting, the belt has broken or slipped off.
Should I replace the idler and rollers with the belt?
Check them while the dryer is open. The idler should spin freely and smoothly, and the drum should turn without wobbling once the belt is off. Many repairers replace all three together, since the belt is already off and worn rollers or a stiff idler shorten the life of a new belt.
My dryer won't do anything when the belt breaks. Why?
Some dryers have a belt switch on the idler. When the belt breaks, the idler drops and opens the switch, so the motor will not start. Replace the belt instead of bypassing the switch. See dryer won't start.
Related
Keep going
- SymptomDryer won't startThe dryer is dead, the lights come on but the drum never turns, or it hums without starting. Start with the breaker and the door, then the thermal fuse, the door switch and the start switch.Open guide
- SymptomDryer squealing, squeaking or thumpingA squeal or squeak usually comes from the idler pulley or a motor bearing. A rhythmic thump usually comes from worn drum rollers, drum glides or a damaged belt. A rattle or knock can be the blower wheel.Open guide
- Dryer partDrum beltThe drum belt wraps around the drum and the motor pulley and turns the drum. When it breaks, the drum stops tumbling. Gas and electric dryers both have one, and the swap is the same on both.Open guide
- Dryer partIdler pulleyThe idler pulley is a small spring-loaded wheel that keeps the drum belt tight. When its bearing wears, it squeals. Gas and electric dryers both have one.Open guide
- Dryer partDrum support rollersDrum support rollers are small wheels the drum rides on. When they wear flat or their bearings dry out, the dryer thumps, rumbles or squeaks. Gas and electric dryers both have them.Open guide
- Dryer partDrive motorThe drive motor turns the drum through the belt and, on many dryers, spins the blower fan too. It is one of the bigger dryer repairs. Gas and electric dryers both have one.Open guide