Dryer won't start
You press Start and nothing happens, or the dryer just hums. Power has to pass a short chain of switches to reach the motor, and one of them is open.
Check these first
Five-minute checks, no tools
Reset the breaker fully
Find the dryer's breaker and switch it all the way off, then back on. A breaker can look on while it is partly tripped. Electric dryers use a double breaker or two breakers side by side: reset both.
Plug pushed all the way in
Check the cord is fully seated in the outlet. Electric dryers use a large 240 V outlet; gas dryers use a normal grounded 120 V outlet. Never run a dryer on an adapter or extension cord.
Door shut all the way
Close the door firmly until it latches. The dryer will not run with the door even slightly open.
Hold Start for a second
Press Start firmly and hold it for about a second. Check that a control lock or delay start setting is not on. Your manual shows the lock light and how to clear it.
Did it quit mid-load?
If the dryer stopped during a long or hot load and now will not start, suspect the thermal fuse. Check the vent hood outside: weak airflow or a stuck flap is the usual reason a fuse blows.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Blown thermal fuse
On many dryers this one-time safety fuse cuts the motor when it blows, so nothing happens when you press Start. It usually blows because the vent is clogged, so clean the exhaust vent before you fit a new one.
Fix the thermal fuse30 min–1 hr$5–$60 - 2DIY fix
Broken drum belt (belt switch models)
On dryers with a belt switch, a snapped belt stops the dryer from starting at all. Unplug the dryer, open the door and turn the drum by hand. If it spins with almost no drag, the belt is likely broken.
Fix the belt30 min–2 hr$10–$70 - 3DIY fix
Door switch
The door switch only lets the dryer run with the door closed. If it fails, the dryer acts as if the door is always open.
Fix the door switch20 min–1 hr$5–$35 - 4DIY fix
Start switch
When pressed, the start switch sends power to the motor. If the lights and display work but pressing Start does nothing, the switch may have failed. It sits behind the control panel.
- 5DIY fix
Drive motor
The dryer hums but the drum never turns, even though the drum and belt move freely by hand. The motor's internal start switch or winding has likely failed, which usually means a new motor.
Fix the motor1 hr–3 hr$60–$200 - 6DIY fix
Timer or control board
If power reaches the dryer and the fuse, door switch and start switch all test good, the timer or electronic control may not be sending power to the motor. Rule out the cheaper parts first.
Fix the timer / board15 min–2 hr$50–$300
What's happening
What your dryer is doing
To start, power runs through a chain: the house breaker, the cord, the door switch, the start switch or control, and on many dryers the thermal fuse, before it reaches the drive motor. Any open link in that chain stops the motor.
On many dryers, electric ones especially, the thermal fuse sits in the motor circuit. When it blows from overheating, the whole dryer stops. On some designs, gas dryers in particular, a blown fuse only cuts the heat. Then the dryer runs cold instead: see dryer not heating.
A hum with no tumbling is different. The motor is getting power but cannot get turning. Either something is jamming the drum or belt, or the motor's own start switch or winding has failed.
Some dryers have a belt switch. If the belt snaps, that switch opens and the dryer will not start at all, so a broken belt can look like a dead dryer.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas near a gas dryer. Do not touch switches or light anything. Get everyone out and call your gas supplier from outside or a neighbor's phone.
- The breaker trips again as soon as you reset it, or the outlet or cord looks scorched or melted. Call an electrician.
- You smell burning, or see scorch marks inside the cabinet.
- The new thermal fuse blows again soon, even after you cleaned the vent.
- You are not comfortable testing parts on a 240 V appliance.
FAQ
Common questions
Can I reset a dryer thermal fuse?
No. A thermal fuse is one-time only. Once it blows it has to be replaced. Never bypass it to get the dryer going: it is the backstop that stops an overheating dryer. See the thermal fuse guide.
Why does my dryer hum but not start?
The motor is getting power but cannot start turning. Unplug the dryer and check that the drum turns and nothing is jammed in it or around the belt. If the drum turns freely and the belt is intact, the motor's start switch or winding has likely failed. See the drive motor guide.
My gas dryer runs but will not heat. Is that this page?
Probably not. On many gas dryers a blown thermal fuse only cuts the heat, so the drum keeps tumbling but stays cold. It depends on the model. See dryer not heating instead.
The lights work, so it can't be the power, right?
Not always. On an electric dryer, one half of a double breaker can trip while the other half keeps the lights and controls alive. Reset the breaker fully first. If it still will not start, the fault is in the door switch, start switch, thermal fuse or motor chain.
Related
Keep going
- SymptomDryer runs but won't tumbleThe dryer starts and the motor runs, but the drum stays still or barely moves. The usual cause is a broken drum belt, then the idler pulley that keeps it tight, then worn drum rollers.Open guide
- SymptomDryer runs but won't heatThe drum tumbles but the air stays cold. On an electric dryer, start with the breaker and the thermal fuse. On a gas dryer, start with the gas shutoff and watch the igniter.Open guide
- SymptomDryer shuts off earlyThe cycle ends, or the dryer stops mid-cycle, and the clothes are still damp. On gas and electric dryers, the usual causes are a blocked vent making it overheat, a coated moisture sensor, or a door that will not stay shut.Open guide
- Dryer partThermal fuseThe thermal fuse is a one-time safety fuse that blows when the dryer overheats. Gas and electric dryers both have one. A blown fuse is a warning about airflow, so clean the vent before you replace it.Open guide
- Dryer partDoor switchGas and electric dryers both have one. The door switch tells the dryer the door is shut. If it fails, the dryer will not start, even with the door closed. It is cheap, easy to test, and usually comes out with a plug and a clip or one screw.Open guide
- Dryer partDrive motorThe drive motor turns the drum through the belt and, on many dryers, spins the blower fan too. It is one of the bigger dryer repairs. Gas and electric dryers both have one.Open guide
- Dryer partExhaust vent and ductThe exhaust duct carries hot, damp air and lint from the back of the dryer to a hood outside. When lint packs into it, drying slows and the dryer runs hot. Gas and electric dryers both need it cleaned about once a year.Open guide