Dryer door switch test and replacement
Good news: if your dryer will not start, this cheap little switch is one of the first things to check, and it usually swaps in under an hour.
- Difficulty
- Easy
- Time
- 20 min–1 hr
- Typical part cost
- $5–$35Pro: $55–$180
- Tools
- 3See the list
A few panel clips or screws, two or three wires and a clip. Reaching it is the hardest part.
What it does
What the door switch does
The door switch sits just inside the door opening. When you close the door, it presses a small plunger or lever on the switch, and the switch closes a circuit that lets the dryer start.
Open the door and the circuit breaks, so the drum stops. That keeps the drum from turning while your hands are inside.
On some dryers the same switch also turns on the drum light when the door is open.
Gas and electric dryers use the same kind of switch. Where it mounts can differ from one dryer to the next.
Why it fails
The switch opens and closes every time you use the door. Over the years its contacts can wear out and stop closing.
The plastic actuator tab on the door, or the lever on the switch, can break off. Then the door no longer presses the switch.
The switch can work loose in its mount, so the door misses it.
Symptoms
Signs of a bad door switch
Will not start with the door shut
You close the door, set a cycle and press start. Nothing happens, or you hear a click and the drum does not turn.
Full diagnosisBroken actuator tab
Look at the door and the door opening. If the small plastic tab that presses the switch is cracked or missing, the switch never gets pressed.
Starts only if you push the door
The dryer runs only while you lean on the door, or it stops when the door is bumped. The switch may be loose or worn.
Full diagnosis
How to test it
Test the door switch before you buy
- Unplug the dryer.
- Open the door and look at the switch plunger or lever in the door opening, and the tab on the door that presses it.
- Press the plunger with a finger. It should move freely and click. Wiggle the switch to see if it is loose.
- Good
- The tab is whole, the plunger clicks and the switch is tight. Move on to the meter test.
- Bad
- A broken tab or a loose switch. Replace the tab or tighten the switch, then try the door again.
- With the dryer unplugged and the switch reachable, take a photo, then pull the wires off the switch.
- Find the common terminal and the one that closes when the door shuts. They are often marked COM and NO. Check your wiring diagram if they are not.
- Touch one probe to each of those two terminals. Press and hold the plunger, then let it go.
A good switch with the plunger pressed typically reads
Near 0 Ω (continuity)
Typical range. Check your part label or manual for the exact spec. Some switches have a third terminal for the drum light. Terminal labels and wire colors vary by model.
- Good
- Continuity with the plunger pressed and open when you let go. The switch is fine. Look at the other [won't start causes](/dryer/symptoms/wont-start).
- Bad
- No continuity with the plunger pressed, or continuity that never breaks. Replace the switch.
Safety first
Before you touch anything
- 1
Unplug the dryer
Pull the dryer's plug from the wall before you remove any panel. Turning the dial to off is not enough.
- 2
Gas dryer? Close the gas shutoff too
This job is nowhere near the burner, but closing the gas shutoff behind the dryer is a cheap second layer of safety. Turn the handle a quarter turn so it sits crosswise to the pipe.
- 3
Watch the sheet metal edges
Panel edges inside a dryer can be sharp. Move slowly when you reach in.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Multi-bit screwdriverPhillips, flat, squarePanel screws and any switch mounting screw.Typically $10–$25Shop this tool
- Putty knifeStiff, 1-1/2 in.Releases the spring clips that hold the top panel on many dryers.Typically $5–$12Shop this tool
- Digital multimeterΩ, V, µF, µAConfirms the switch is dead before you buy a new one.Typically $25–$60Shop this tool
- Needle-nose pliersOptionalPulls push-on terminals straight off without bending them.Typically $8–$20Shop this tool
- Painter's tape and markerOptionalLabel the wires before you take them off.Typically $5–$12Shop this tool
Step by step
How to replace the door switch
- 1
Unplug the dryer
Pull the dryer out far enough to reach the plug and unplug it.
On a gas dryer, also turn the gas shutoff handle crosswise to the pipe.
- 2
Get to the switch
On some dryers the switch sits in the door opening and pops out from the front, after you remove one screw or ease it out with a putty knife. If yours does, skip ahead to unplugging it.
On many others you lift the top panel. Slide a putty knife into the seam between the top and front panels, a couple of inches in from each corner, and push to release the spring clips. Older models may have two screws at the back edge instead.
Tip. Lay a towel on the top before you prop it up so it does not scratch the wall.
- 3
Find the switch
Look on the inside of the front panel, at the door opening. The switch is a small plastic box with two or three wires, lined up with the tab on the door.
On some models you need to remove the front panel to reach it. That is usually two screws along its top edge.
Tip. Take a photo of the wires now.
- 4
Unplug the wires
Pull the connector or the push-on terminals off the switch. Grip the connector, not the wires. Label each wire if they come off one at a time.
- 5
Release the switch
Many switches snap in with two tabs. Pinch the tabs toward the switch body and push it out of its hole. If yours has a screw, take it out first.
- 6
Match the new switch
Hold the old and new switches side by side. The shape, the plunger and the terminals should match.
Buy the part
Door switch
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- Your dryer's model number from the rating plate inside the door. Search by that.
- The same shape, mounting tabs and plunger as the old switch.
- The same number of terminals. A switch that also runs the drum light usually has three.
- 7
Snap in the new switch
Line the new switch up the same way as the old one, with the plunger facing the door. Push it into the hole until the tabs click, or refit its screw.
- 8
Reconnect the wires
Push the connector or terminals back on, matching your photo and labels.
- 9
Close it up
Refit the front panel if you took it off. Lower the top panel and press down at the front corners until the clips snap, or refit its screws.
- 10
Plug in and test
Open the gas shutoff on a gas dryer, then plug the dryer in.
Close the door and start a cycle. The drum should turn. Open the door and it should stop.
Buy the part
Get the right replacement
Buy the part
Door switch
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- Your dryer's model number from the rating plate inside the door. Search by that.
- The same shape, mounting tabs and plunger as the old switch.
- The same number of terminals. A switch that also runs the drum light usually has three.
Know your limits
When to call a pro
Stop and call a pro if
- Gas dryer and you smell gas at any point. Do not touch any switches. Leave the house and call your gas supplier from outside.
- A new door switch does not fix it and you have already checked the thermal fuse and the start button.
- You see melted plastic, scorch marks or burned wires at the switch.
- The dryer starts with the door open. That is a safety problem. Unplug it and do not use it until it is fixed.
FAQ
Door switch questions
My dryer will not start. Is it the door switch?
It is one of the first things to check, because it is cheap and easy to test. Other common causes are a blown thermal fuse, a broken drum belt on dryers with a belt switch, and the start button. Our won't start guide walks through the order.
Can I bypass the door switch to test the dryer?
No. The switch stops the drum when the door opens. Running a dryer with it bypassed is unsafe. Test the switch with a meter instead.
Do gas and electric dryers use the same door switch?
They work the same way, and the steps on this page apply to both. The exact part varies by model, so always buy by your model number.
Why does my drum light not work?
On some dryers the door switch also runs the drum light, so a bad switch can kill both. Check the bulb first. If the dryer will not start either, test the switch.
Related
Keep going
- SymptomDryer won't startThe dryer is dead, the lights come on but the drum never turns, or it hums without starting. Start with the breaker and the door, then the thermal fuse, the door switch and the start switch.Open guide
- SymptomDryer runs but won't tumbleThe dryer starts and the motor runs, but the drum stays still or barely moves. The usual cause is a broken drum belt, then the idler pulley that keeps it tight, then worn drum rollers.Open guide
- Dryer partThermal fuseThe thermal fuse is a one-time safety fuse that blows when the dryer overheats. Gas and electric dryers both have one. A blown fuse is a warning about airflow, so clean the vent before you replace it.Open guide
- Dryer partDrum beltThe drum belt wraps around the drum and the motor pulley and turns the drum. When it breaks, the drum stops tumbling. Gas and electric dryers both have one, and the swap is the same on both.Open guide
- Dryer partTimer or control boardGas and electric dryers both have one. Older dryers use a mechanical timer with a dial. Newer ones use an electronic control board with buttons and a display. Either can fail, but they cost more than most dryer parts, so rule out the cheaper causes before you buy one.Open guide
