Dryer runs but won't heat
The drum turns, so the motor and the controls are fine. The problem is somewhere in the heat path, and that is a short list.
Check these first
Five-minute checks, no tools
Both halves of the breaker on
Electric dryers use a double breaker. One half can trip while the other stays on. Switch it fully off, then fully back on. If it is a fuse box, check both fuses.
Gas shutoff open
Gas dryers only. The handle on the gas line behind the dryer should sit in line with the pipe. Crosswise means closed, and the drum still turns with the gas off.
Lint screen clean
Pull the [lint screen](/dryer/lint-screen) and clear it. A clogged screen makes the dryer overheat and trip its safety parts.
Air coming out outside
Run the dryer and check the outside hood. Weak air or a flap that stays shut points to a blocked [exhaust vent](/dryer/exhaust-vent).
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Thermal fuse
Gas and electric. A one-time safety fuse that blows when the dryer overheats. On many gas dryers a blown fuse just stops the heat. On many electric dryers it stops the dryer running at all. Find out why it blew before you replace it.
Fix the thermal fuse30 min–1 hr$5–$60 - 2DIY fix
Heating element
Electric only. The coil can break or burn through, and then it cannot heat at all. A continuity test with the dryer unplugged tells you.
Fix the element45 min–2 hr$30–$90 - 3DIY fix
Igniter
Gas only. If you never see the igniter glow when the dryer calls for heat, the igniter itself may be burned out. Check the thermal fuse and thermostats too, since they sit ahead of it.
Fix the igniter30 min–1 hr$15–$85 - 4DIY fix
One side of the breaker tripped
Electric only. Half the double breaker is off, so the dryer gets enough power to tumble but not to heat. If it keeps tripping, call an electrician.
- 5DIY fix
Cycling thermostat
Gas and electric. It switches the heat on and off to hold the temperature. If it fails open, the heat never comes on.
Fix the cycling thermostat20–45 min$5–$60 - 6Call a pro
Gas valve coils
Gas only. The igniter glows, then goes out, and no flame follows. The coils that open the gas valve may be weak. This is gas valve work, so it is for a pro.
- 7DIY fix
Gas shutoff closed
Gas only. A closed shutoff, often after the dryer was moved or installed, means no gas reaches the burner. The drum still turns.
- 8DIY fix
Flame sensor
Gas only. The igniter glows and keeps glowing for a long time, but the gas never lights. The flame sensor may not be letting the valve open.
Fix the flame sensor20–45 min$10–$40 - 9DIY fix
High-limit thermostat
Gas and electric. A backup safety switch that cuts the heat if the dryer overheats. Restricted airflow is the usual reason it trips, so check the vent too.
Fix the high limit20–45 min$5–$35 - 10Call a pro
Burner problem
Gas only, and rare. A corroded burner tube or the wrong orifice can stop the gas lighting or staying lit. Burner work is gas work and is for a pro.
What's happening
What your dryer is doing
An electric dryer runs on 240 V. The motor and controls need only half of that, but the heating element needs the full 240 V. So when one side of the double breaker trips, the dryer can tumble happily and never get warm.
Power to the element passes through a chain of safety parts on the way: the thermal fuse, the high-limit thermostat and the cycling thermostat. If any link opens, the heating element gets nothing.
A gas dryer uses a burner instead of an element. When it calls for heat, the igniter glows, the gas valve coils open the valve, and the gas lights. A flame sensor near the burner tells the dryer when the flame is lit. A closed gas shutoff stops all of it.
On both kinds, the link that breaks most often is the thermal fuse. It blows when the dryer gets too hot, and that usually means a blocked lint screen or vent. Fix the airflow, or the new fuse blows too.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas. Do not touch any switches or the plug. Leave the house and call your gas utility from outside.
- Gas dryer: the igniter glows, then goes out, and no flame follows. Gas valve coil work is for a pro.
- Gas dryer: the flame looks yellow, lazy or sputtering instead of steady and mostly blue.
- Electric dryer: the breaker trips again after you reset it, or the outlet or plug looks scorched. Call an electrician.
- A new thermal fuse blows again soon after you fit it, and the vent is clear.
- Your gas dryer's gas line and connection have not been checked in years. Fire safety agencies suggest a professional inspection.
FAQ
Common questions
Why does my dryer spin but not heat?
Turning the drum and making heat are separate jobs. On an electric dryer, a half-tripped breaker or a break in the heat circuit stops the heat while the motor keeps going. On a gas dryer, a closed gas shutoff or a fault at the igniter, flame sensor or gas valve does the same.
Should I just replace the thermal fuse?
Test it first, and if it has blown, find out why. A fuse blows when the dryer overheats, usually from a clogged lint screen or vent. Clean the exhaust vent before you fit a new one, or it will blow again.
Never bypass the fuse to get the dryer going. It is what stops an overheating dryer from catching fire.
Can I fix a gas dryer that won't heat myself?
Some of it. Opening the gas shutoff, and testing or replacing the thermal fuse, the thermostats, the igniter or the flame sensor with the dryer unplugged, are owner jobs. The gas valve coils, the gas valve and the burner are gas work, and those go to a pro.
The breaker looks on. Can it still be the problem?
Yes. One half of a double breaker can trip while the handle barely moves. Switch it fully off, then fully on. If the dryer still will not heat and you want to check the supply voltage, that is a job for an electrician.
Related
Keep going
- SymptomDryer takes too long to dryLoads need two cycles, or come out damp. On gas and electric dryers alike, the usual cause is restricted airflow: a clogged lint screen, a blocked vent or a crushed duct. Load size matters too.Open guide
- SymptomDryer shuts off earlyThe cycle ends, or the dryer stops mid-cycle, and the clothes are still damp. On gas and electric dryers, the usual causes are a blocked vent making it overheat, a coated moisture sensor, or a door that will not stay shut.Open guide
- SymptomDryer won't startThe dryer is dead, the lights come on but the drum never turns, or it hums without starting. Start with the breaker and the door, then the thermal fuse, the door switch and the start switch.Open guide
- Dryer partThermal fuseThe thermal fuse is a one-time safety fuse that blows when the dryer overheats. Gas and electric dryers both have one. A blown fuse is a warning about airflow, so clean the vent before you replace it.Open guide
- Dryer partHeating elementElectric dryers only. The heating element is a coil of resistance wire that heats the air on its way into the drum. A broken coil means no heat. A quick ohm test confirms it.Open guide
- Dryer partGas dryer igniterGas dryers only. The igniter is a small ceramic element that glows hot enough to light the gas. When it fails, the drum turns but the dryer never heats. You can test it with a meter and, on many dryers, swap it without touching any gas fittings.Open guide
- Dryer partExhaust vent and ductThe exhaust duct carries hot, damp air and lint from the back of the dryer to a hood outside. When lint packs into it, drying slows and the dryer runs hot. Gas and electric dryers both need it cleaned about once a year.Open guide