Dryer cycling thermostat: test and replace
This small round switch decides when your dryer heats. It is cheap, it is held by two screws, and testing it takes a minute.
- Difficulty
- Easy
- Time
- 20–45 min
- Typical part cost
- $5–$60Pro: $80–$200
- Tools
- 5See the list
Two screws and two or more wires once you can see it. Getting to it usually means taking off a back or front panel.
What it does
What the cycling thermostat does
The cycling thermostat is a small round switch that sits in the air path leaving the drum, often on the blower housing or the exhaust duct. It senses how hot the exhaust air is.
When the air is cool, its contacts are closed and the heat runs. When the air reaches the set temperature, the contacts open and the heat shuts off. As the air cools, they close again. That on and off cycle is what holds the dryer at a steady temperature.
Gas and electric dryers both have one. On an electric dryer it switches the heating element. On a gas dryer it switches the burner circuit.
Some newer dryers with electronic controls use a temperature sensor called a thermistor instead. If you cannot find a round thermostat on the blower housing, check your manual.
Why it fails
The contacts open and close many times every load. Over the years they can wear or burn and stay open. An open thermostat means no heat.
Less often, the contacts stick closed. Then nothing switches the heat off, the dryer runs too hot and the safety parts take over. A thermal fuse that keeps blowing on a clean vent can be a sign of this.
Symptoms
Signs of a bad cycling thermostat
Tumbles, but no heat
A thermostat stuck open never lets the heat come on. The drum turns, the clothes stay cold.
Full diagnosisRuns too hot, or keeps blowing fuses
Clothes come out very hot, the cabinet is hot to the touch, or new thermal fuses keep blowing on a clean vent. A thermostat stuck closed can do that.
Full diagnosis
How to test it
Test the cycling thermostat before you buy
- Unplug the dryer. On a gas dryer, also close the gas shutoff. Let it cool to room temperature.
- Take off the panel that gets you to the blower housing and find the round thermostat in the air path.
- Check the wires with a voltage tester, take a photo, then pull the wires off its two main terminals.
- Touch one probe to each of those terminals.
A good thermostat at room temperature shows
Continuity (near 0 Ω)
Typical range. Check your part label or manual for the exact spec. A pass does not prove the thermostat opens at the right temperature. If the dryer runs too hot and this test passes, the thermostat can still be the cause. Fix any airflow problem first, then consider replacing it.
- Good
- Near zero, or a beep, means the contacts are closed as they should be when cool.
- Bad
- OL, or no beep, at room temperature means the thermostat is stuck open. Replace it.
Safety first
Before you touch anything
- 1
Unplug the dryer
Pull the plug from the wall. If you cannot reach it, turn off the dryer's breaker. Check the thermostat wires with a voltage tester before you touch them.
- 2
Gas dryer: close the gas shutoff
Turn the handle on the dryer's gas line a quarter turn so it sits crosswise to the pipe. You will not open any gas fittings. This is just a second layer of safety.
- 3
Let it cool
A warm thermostat can read open and still be fine. Let the dryer sit until the housing is at room temperature.
Wait about 20 min
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexPanel and thermostat screws are often 1/4 in. hex heads.Typically $6–$15Shop this tool
- Nut driver5/16 in. hexThe other common dryer screw size.Typically $6–$15Shop this tool
- Digital multimeterΩ, V, µF, µAA continuity test shows whether the thermostat is stuck open.Typically $25–$60Shop this tool
- Non-contact voltage testerPen styleConfirms the dryer is dead before you touch the thermostat wires.Typically $15–$30Shop this tool
- Needle-nose pliersPulls tight spade connectors straight off the terminals.Typically $8–$20Shop this tool
- Painter's tape and markerOptionalLabel each wire before you pull it.Typically $5–$12Shop this tool
Step by step
How to replace the cycling thermostat
- 1
Unplug the dryer and close the gas
Pull the dryer out and unplug it. On a gas dryer, turn the gas shutoff handle a quarter turn so it sits crosswise to the pipe. Move the dryer gently so you do not strain the gas line.
- 2
Take off the access panel
The thermostat is in the air path from the drum, often on the blower housing. On many dryers that means taking off the back panel. Your manual or parts diagram shows the way in for your model.
- 3
Label and disconnect the wires
Find the round thermostat on the blower housing. Hold the voltage tester to its wires. It should stay quiet.
Take a photo and tag each wire. Some cycling thermostats have more than two terminals, and every wire has to go back where it came from.
Pull the wires straight off. Grip the connector, not the wire.
- 4
Remove the old thermostat
Back out the screws that hold it to the housing and lift it off. Keep the screws.
- 5
Match the new thermostat
Compare the new part with the old one. The part number, the terminals and the mounting flange should match, or the new part should list your dryer's model number. Cycling thermostats look alike but are made for different temperatures.
Buy the part
Cycling thermostat
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- The part number stamped on the old thermostat, or the dryer's model number from the rating plate inside the door.
- The same number of terminals and the same mounting flange.
- The same temperature rating. Thermostats that look identical can open at different temperatures.
- 6
Install it and reconnect the wires
Set the new thermostat flat against the housing and drive the screws in snug. Push each wire back onto its terminal, matching your photo.
- 7
Close up and run a heat cycle
Refit the panel. On a gas dryer, turn the gas handle back in line with the pipe. Plug the dryer in and run a timed heat cycle.
The air should get warm, and the clothes should come out warm but not scorching.
Buy the part
Get the right replacement
Buy the part
Cycling thermostat
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- The part number stamped on the old thermostat, or the dryer's model number from the rating plate inside the door.
- The same number of terminals and the same mounting flange.
- The same temperature rating. Thermostats that look identical can open at different temperatures.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas at any point. Do not touch any switches. Leave the house and call your gas utility from outside.
- The dryer still runs too hot with a new thermostat and a clean vent.
- You see melted wires or scorched terminals near the thermostat.
- Your dryer uses a thermistor and an electronic control, and the fault points to the control board.
FAQ
Cycling thermostat questions
What is the difference between the cycling and the high-limit thermostat?
The cycling thermostat does the everyday work. It switches the heat on and off every load to hold the temperature.
The high-limit thermostat is a safety backup. It should only open if the dryer overheats.
My thermostat passes the continuity test. Can it still be bad?
Yes. The test only shows it is closed when cold. It cannot show whether it opens at the right temperature. If the dryer runs too hot and the vent is clean, the thermostat is still a suspect.
Do gas dryers have a cycling thermostat?
Yes. Gas and electric dryers both use one in the exhaust air path. On a gas dryer it switches the burner circuit instead of an element.
Related
Keep going
- SymptomDryer runs but won't heatThe drum tumbles but the air stays cold. On an electric dryer, start with the breaker and the thermal fuse. On a gas dryer, start with the gas shutoff and watch the igniter.Open guide
- SymptomDryer shuts off earlyThe cycle ends, or the dryer stops mid-cycle, and the clothes are still damp. On gas and electric dryers, the usual causes are a blocked vent making it overheat, a coated moisture sensor, or a door that will not stay shut.Open guide
- Dryer partHigh-limit thermostatThe high-limit thermostat cuts the heat if the dryer overheats. Gas and electric dryers both have one, at the heat source. If it fails open, the dryer tumbles with no heat.Open guide
- Dryer partThermal fuseThe thermal fuse is a one-time safety fuse that blows when the dryer overheats. Gas and electric dryers both have one. A blown fuse is a warning about airflow, so clean the vent before you replace it.Open guide
- Dryer partHeating elementElectric dryers only. The heating element is a coil of resistance wire that heats the air on its way into the drum. A broken coil means no heat. A quick ohm test confirms it.Open guide
- Dryer partExhaust vent and ductThe exhaust duct carries hot, damp air and lint from the back of the dryer to a hood outside. When lint packs into it, drying slows and the dryer runs hot. Gas and electric dryers both need it cleaned about once a year.Open guide
