Dryer shuts off before the clothes are dry
A dryer that quits early is usually either protecting itself from heat or being fooled into thinking the load is dry. Both are easy to check.
Check these first
Five-minute checks, no tools
Lint screen clear
Clear the [lint screen](/dryer/lint-screen) and make sure it is seated. A clogged screen is the quickest overheating fix there is.
Air coming out outside
Run the dryer and check the outside hood. Weak air or a flap that stays shut means the [exhaust vent](/dryer/exhaust-vent) needs cleaning.
Try a timed cycle
Run the same kind of load on a timed dry setting instead of auto-dry. If timed dry works and auto-dry quits early, the moisture sensor is the suspect.
Door shuts firmly
Close the door and press gently. It should latch and stay shut. A worn latch can let it pop open a little during the cycle.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Blocked vent, dryer overheating
Lint in the duct or a crushed hose traps the heat, and the dryer shuts off to protect itself. Clothes or the top of the dryer feel unusually hot.
Fix the exhaust vent30 min–1.5 hr$15–$30 - 2DIY fix
Moisture sensor coated
Auto-dry ends early but timed dry works. Softener residue on the sensor bars inside the drum makes damp clothes read as dry. With the dryer unplugged, wipe the bars with a soft cloth and warm, mildly soapy water, then dry them.
- 3DIY fix
Door switch or latch
The dryer stops as if the door opened. A worn latch lets the door ease open, or a failing switch loses contact.
Fix the door switch20 min–1 hr$5–$35 - 4DIY fix
Lint screen clogged
A full or coated screen chokes the airflow and lets the dryer overheat. Clear it every load.
Fix the lint screen5–20 min$20–$100 - 5DIY fix
Thermal fuse blown
The dryer stopped mid-load and now will not run, or runs with no heat. The fuse blows when the dryer overheats. Fix the airflow before you replace it.
Fix the thermal fuse30 min–1 hr$5–$60 - 6DIY fix
Drive motor overheating
The dryer stops, sits for a while, then starts again once it cools. Many dryer motors have a built-in overload protector that shuts the motor off when it overheats and resets once it cools. A worn motor can trip it again and again.
Fix the motor1 hr–3 hr$60–$200
What's happening
What your dryer is doing
When hot air cannot leave through the vent, heat builds up inside the dryer. Its safety devices react by cutting the heat or stopping the dryer. That protects the dryer and your home, but it leaves you with damp clothes.
Auto-dry cycles end when two metal bars inside the drum sense the clothes are dry. Dryer sheet and softener residue coats those bars, so the dryer reads damp clothes as dry and ends the cycle too soon.
Some dryers stop because the door switch thinks the door opened, or because the motor got too hot and its overload protector shut it off. That protector resets once the motor cools, so the dryer may start again later.
If the dryer stopped and now will not start at all, the thermal fuse may have blown. See dryer won't start.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas near a gas dryer. Leave the house and call your gas utility from outside.
- You smell burning, see smoke, or the cabinet is too hot to touch. Unplug the dryer and do not use it until it has been checked.
- It still stops early after you clean the lint screen, the vent and the sensor bars.
- A new thermal fuse blows again soon after you fit it.
- The motor keeps shutting off and restarting after it cools. Stop using the dryer and have the motor checked.
- The vent runs to the roof, is very long, or you cannot reach the outside hood safely.
FAQ
Common questions
Why does my dryer stop before the clothes are dry?
The two big reasons are overheating and the moisture sensor. A blocked vent makes the dryer cut out to protect itself. A coated moisture sensor makes auto-dry think damp clothes are dry. Try a timed cycle to tell them apart.
How do I clean the moisture sensor?
Unplug the dryer. Find the two metal strips inside the drum. Your manual shows where they are. Wipe them with a soft cloth and warm water with a little mild soap, then dry them with a clean cloth. No sandpaper or scouring pads. Your manual may name a different cleaner, so follow it. Clean them more often if you use dryer sheets.
Is it safe to keep running a dryer that keeps shutting off?
If it is overheating, no. The dryer is telling you the heat cannot get out, and lint that traps heat is fuel for a fire. Clean the lint screen and the exhaust vent before you run more loads, and do not run it while you are out or asleep.
Related
Keep going
- SymptomDryer takes too long to dryLoads need two cycles, or come out damp. On gas and electric dryers alike, the usual cause is restricted airflow: a clogged lint screen, a blocked vent or a crushed duct. Load size matters too.Open guide
- SymptomDryer runs but won't heatThe drum tumbles but the air stays cold. On an electric dryer, start with the breaker and the thermal fuse. On a gas dryer, start with the gas shutoff and watch the igniter.Open guide
- SymptomDryer won't startThe dryer is dead, the lights come on but the drum never turns, or it hums without starting. Start with the breaker and the door, then the thermal fuse, the door switch and the start switch.Open guide
- Dryer partExhaust vent and ductThe exhaust duct carries hot, damp air and lint from the back of the dryer to a hood outside. When lint packs into it, drying slows and the dryer runs hot. Gas and electric dryers both need it cleaned about once a year.Open guide
- Dryer partLint screenThe lint screen catches fluff before it reaches the vent. A clogged or coated screen slows drying and makes the dryer run hot. Gas and electric dryers both have one, and cleaning it takes a minute.Open guide
- Dryer partDoor switchGas and electric dryers both have one. The door switch tells the dryer the door is shut. If it fails, the dryer will not start, even with the door closed. It is cheap, easy to test, and usually comes out with a plug and a clip or one screw.Open guide
- Dryer partThermal fuseThe thermal fuse is a one-time safety fuse that blows when the dryer overheats. Gas and electric dryers both have one. A blown fuse is a warning about airflow, so clean the vent before you replace it.Open guide