Dryer lint screen cleaning and replacement
Good news: this is the cheapest fix on the whole dryer. A quick wipe every load, a good wash now and then, and your dryer breathes easy.
- Difficulty
- Anyone can do it
- Time
- 5–20 min
- Typical part cost
- $20–$100Pro: $100–$185
- Tools
- 1See the list
No tools to remove it and nothing to wire. The only real job is letting it dry fully after a wash.
What it does
What the lint screen does
The lint screen is a fine mesh filter that slides into a slot, usually in the door opening or on top of the dryer. Gas and electric dryers both have one, and it works the same way in both.
Every bit of air that dries your clothes passes through it on the way to the vent. The mesh catches the loose fibers so they do not pack into the blower and the duct.
That matters for more than drying time. Lint is one of the things most often first ignited in dryer fires, and lint blocking the airflow is what lets a dryer overheat.
Why it fails
Mostly it just fills up. Fire safety groups say to clear it before or after every load, and skipped cleaning is the leading factor in home dryer fires.
Dryer sheets and liquid softener leave a waxy film on the mesh that you cannot see. A screen can look clean and still block air. Running water over it shows the problem: the water pools instead of passing through.
Screens also tear, or the frame warps or cracks. Then lint slips past it into the blower and duct, where it restricts airflow and can blow the thermal fuse.
Symptoms
Signs of a bad lint screen
Clothes take longer to dry
A packed or coated screen chokes the airflow, so loads need an extra cycle. Clean the screen first, then check the vent.
Full diagnosisWater pools on the screen
Run tap water over the clean screen. If it beads up and sits there instead of running through, a film of softener residue is clogging the mesh.
A hole or a bent frame
Hold the screen up to a light. Holes, mesh pulling away from the frame, or a frame that will not sit flush mean lint is getting past it.
The dryer runs hot or stops early
A blocked screen lets heat build up inside the dryer, and its safety devices may cut the heat or stop the cycle.
Full diagnosis
How to test it
Test the lint screen before you buy
- Peel off the loose lint first.
- Hold the screen flat under a running tap, or pour a cup of water onto the mesh.
- Watch where the water goes.
- Good
- The water runs straight through the mesh. The screen is open. A quick lint wipe each load is all it needs.
- Bad
- The water pools or beads on top. Residue is blocking the mesh. Wash it with warm soapy water and a nylon brush, then test again.
- Hold the clean, dry screen up to a window or a lamp.
- Look over the whole mesh and run a finger around the frame.
- Good
- The mesh is whole, tight to the frame, and the frame is straight.
- Bad
- Holes, tears, mesh pulling loose, or a cracked or warped frame. Replace the screen.
Safety first
Before you touch anything
- 1
Stop and unplug the dryer
For a quick lint wipe, just stop the dryer. For a deep clean, where you reach into the slot with a vacuum nozzle, unplug it first. This goes for gas and electric dryers alike.
- 2
Let it cool
If the dryer just ran, give it a few minutes. The screen and the slot can be hot.
Wait about 5 min
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Stiff nylon brushScrubs the softener film out of the mesh without tearing it.Typically $5–$12Shop this tool
- Shop vacuumOptionalA crevice tool pulls loose lint out of the slot the screen sits in.Typically $40–$90Shop this tool
Step by step
How to clean or replace the lint screen
- 1
Stop the dryer and unplug it
Stop the cycle and open the door. If you plan to vacuum the slot, pull the plug as well.
On a gas dryer there is nothing to do with the gas for this job. You are not opening the cabinet.
- 2
Pull out the screen
Find the screen. On many dryers it sits in the bottom of the door opening. On others it is on top, toward the back. Grip the handle and pull it straight out.
- 3
Peel off the lint
Roll the lint off with your fingers. It should come away in a sheet. Throw it in the trash.
Do this dry. Wet lint smears into the mesh and is much harder to get off.
Tip. This is the step to do every single load. The rest is for a deep clean every few months.
- 4
Wash off the residue
Every six months or so, or whenever the water test shows pooling, wash the screen. Wet it with warm water and a little liquid detergent or dish soap. Scrub both sides gently with the nylon brush.
Rinse it and run the water test again. If the water still pools, let it soak in warm soapy water for a while and scrub again.
Careful. Scrub gently. The mesh is fine and tears if you push hard or use anything sharp.
- 5
Check it, and replace it if it is damaged
Hold it up to a light. A torn mesh, mesh pulling off the frame, or a warped or cracked frame means it needs replacing.
Match the new one by your dryer's model number. It is on the rating plate, usually inside the door frame.
Buy the part
Lint screen
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- Your dryer's model number, from the rating plate inside the door frame. Screens are shaped to fit one slot.
- The same length, width and handle style as the old one.
- A frame that seats flush, with no gap where lint can slip around it.
Screens are made to fit a specific slot, so buy by model number. A screen that does not seat snugly lets lint past, which defeats the point.
- 6
Vacuum the slot
With the dryer unplugged, run a vacuum crevice tool down into the slot where the screen sits. Lint collects there and around the opening.
Only go as far as the nozzle reaches easily. Lint packed deep inside the dryer is a job for when the cabinet is open, or for a pro.
- 7
Dry it fully and slide it back in
Pat the screen dry with a towel and let it air dry until it is completely dry. Then slide it back into its slot until it seats flush.
Never run the dryer with the screen out, loose or damaged, even for one load. That is how lint reaches the blower and the vent.
- 8
Plug it back in
Plug the dryer back in and run your next load as normal. Make clearing the screen part of every load from now on.
Buy the part
Get the right replacement
Buy the part
Lint screen
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- Your dryer's model number, from the rating plate inside the door frame. Screens are shaped to fit one slot.
- The same length, width and handle style as the old one.
- A frame that seats flush, with no gap where lint can slip around it.
Screens are made to fit a specific slot, so buy by model number. A screen that does not seat snugly lets lint past, which defeats the point.
Know your limits
When to call a pro
Stop and call a pro if
- You smell burning or see scorch marks near the screen slot. Stop using the dryer until it has been looked at.
- You smell gas near a gas dryer. Leave the house and call your gas utility from outside.
- A damaged screen let lint through for a while. Lint may be packed in the blower or the duct, and a vent cleaning service can clear it.
- Clothes still take too long after a clean screen and a clear vent.
FAQ
Lint screen questions
How often should I clean the lint screen?
Every load, before or after. That is the advice from fire safety groups. Give it a wash with warm soapy water about every six months, or sooner if you use dryer sheets and the water test shows pooling.
Can I run the dryer without the lint screen for one load?
No. Without it, lint goes straight into the blower and the vent duct. That slows drying, makes the dryer run hot and builds up the fuel for a dryer fire. Wait until the screen is back in and dry.
My screen looks clean. Why does water sit on it?
Dryer sheets and liquid softener leave a thin, waxy film on the mesh. You cannot see it, but it blocks air. Wash the screen with warm water, a little detergent and a soft brush until water runs straight through.
Is a clean lint screen enough to prevent dryer fires?
It is the big one, but not the only one. Lint still gets past the screen into the vent duct. Clean the exhaust vent about once a year, or sooner if drying times creep up.
Related
Keep going
- SymptomDryer takes too long to dryLoads need two cycles, or come out damp. On gas and electric dryers alike, the usual cause is restricted airflow: a clogged lint screen, a blocked vent or a crushed duct. Load size matters too.Open guide
- SymptomDryer shuts off earlyThe cycle ends, or the dryer stops mid-cycle, and the clothes are still damp. On gas and electric dryers, the usual causes are a blocked vent making it overheat, a coated moisture sensor, or a door that will not stay shut.Open guide
- SymptomDryer runs but won't heatThe drum tumbles but the air stays cold. On an electric dryer, start with the breaker and the thermal fuse. On a gas dryer, start with the gas shutoff and watch the igniter.Open guide
- Dryer partExhaust vent and ductThe exhaust duct carries hot, damp air and lint from the back of the dryer to a hood outside. When lint packs into it, drying slows and the dryer runs hot. Gas and electric dryers both need it cleaned about once a year.Open guide
- Dryer partThermal fuseThe thermal fuse is a one-time safety fuse that blows when the dryer overheats. Gas and electric dryers both have one. A blown fuse is a warning about airflow, so clean the vent before you replace it.Open guide
- Dryer partBlower wheelThe blower wheel is the fan that pulls air through the drum and pushes it out the vent. A cracked, loose or lint-packed wheel means slow drying and odd noises. Gas and electric dryers both have one.Open guide
