Dryer blower wheel replacement
Clean vent, clean lint screen, and loads still take forever? A cracked or loose blower wheel may be the reason. Check the cheap stuff first, then dig in.
- Difficulty
- Moderate
- Time
- 45 min–2 hr
- Typical part cost
- $10–$60Pro: $100–$350
- Tools
- 7See the list
Reaching the wheel can mean taking the drum out, and old wheels can be stubborn on the shaft. Not hard, but plan for some wrestling.
What it does
What the blower does
The blower wheel is a plastic or metal fan inside a housing low in the cabinet. It pulls warm, damp air out of the drum, through the lint screen, and pushes it out the exhaust duct to the outside.
On many dryers it threads onto one end of the drive motor shaft, so the same motor turns the drum and the fan. Some dryers clamp it to the shaft instead, and some give it a separate motor.
Gas and electric dryers both use one. Without good airflow, clothes stay damp no matter how hot the dryer runs.
Why it fails
Plastic wheels get brittle with age and heat. Blades crack or break off, and a broken blade throws the wheel off balance.
The wheel can work loose on the motor shaft, or its hub can strip, so it slips or stops turning with the motor.
Lint that gets past the screen can pack the wheel and housing, cutting airflow and loading the motor.
Symptoms
Signs of a bad blower
Loads take two or three cycles
The dryer heats but clothes stay damp. Airflow is down but not gone. Check the vent and lint screen first.
Full diagnosisWeak air at the outside vent, with a clean duct
If the [exhaust vent](/dryer/exhaust-vent) is clean but little air comes out of the hood outside, the wheel may be cracked, broken or loose on the shaft.
Thumping, rattling or rumbling
A broken blade throws the wheel off balance and thumps or rattles. A high squeal or a loud rumble can come from the wheel too.
Full diagnosis
How to test it
Test the blower before you buy
- First make sure the lint screen is clean and the exhaust duct is clear.
- Run the dryer on an air-only or low-heat setting and hold your hand near the vent hood outside.
- Good
- A strong, steady stream of air. The blower is probably fine.
- Bad
- Weak air or none, even with a clean duct and lint screen. Look at the blower wheel next.
- Unplug the dryer and open the blower housing (see the steps below).
- Look at each blade and at the hub where it meets the motor shaft. Try to turn the wheel while you hold the shaft still.
- Good
- No cracked or missing blades, no packed lint, and the wheel is tight on the shaft.
- Bad
- Cracked or missing blades, a stripped hub, or a wheel that turns on the shaft. Replace it. Packed lint alone just needs cleaning.
Safety first
Before you touch anything
- 1
Unplug the dryer
Pull the power cord from the wall. If you cannot reach the plug, turn off the dryer's breaker. Do this before you take off any panel.
- 2
Gas dryers: close the gas shutoff
Turn the shutoff handle on the gas line behind the dryer a quarter turn so it sits crosswise to the pipe. You will not open any gas fittings. If you pull the dryer out, move it gently so you do not kink or strain the gas line.
- 3
Wear gloves
The sheet metal edges inside a dryer cabinet can be sharp.
- 4
Let it cool
If the dryer just ran, let it cool before you reach in.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexMany dryer panel and blower housing screws are 1/4 in. hex heads.Typically $6–$15Shop this tool
- Nut driver5/16 in. hexThe other common panel and housing screw size.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareFor Phillips screws on panels, the lint duct and clamp-style wheels.Typically $10–$25Shop this tool
- Adjustable wrench8–10 in.Holds the flat on the motor shaft still while you turn the wheel.Typically $10–$25Shop this tool
- Socket set1/4 in. drive, with extensionA second wrench for the wheel hub on threaded wheels. Sizes vary by model.Typically $20–$45Shop this tool
- Shop vacuumClears packed lint out of the blower housing while it is open.Typically $40–$90Shop this tool
- Work glovesDryer cabinet edges can be sharp.Typically $8–$20Shop this tool
Step by step
How to replace the blower
- 1
Unplug the dryer and close the gas
Pull the power cord from the wall, or turn off the dryer's breaker if you cannot reach the plug.
On a gas dryer, also turn the gas shutoff handle a quarter turn so it sits crosswise to the pipe.
Careful. If you slide the dryer out, move it gently. Do not kink or strain the gas line, and never disconnect it yourself.
- 2
Get to the blower housing
Where the blower sits depends on the dryer. On many, you open the top, take off the front panel, free the belt and lift the drum out, and the blower is at the front end of the motor. On others, the blower housing comes off without taking the drum or motor out.
Check your dryer's service manual or tech sheet for your model. Label and unplug the door switch wires if the front panel comes off.
Careful. If you free the belt, keep hold of the spring-loaded idler so it does not snap back on your fingers.
- 3
Open the blower housing
Remove the screws that hold the blower housing cover or the lint duct over the wheel, and set them aside.
Take a photo of how the housing and any seals fit.
- 4
Take the wheel off the shaft
Threaded wheel: hold the motor shaft still with a wrench on the flat at the pulley end, and turn the wheel hub with a second wrench. It is usually reverse threaded, so it loosens clockwise. Many wheels have an arrow. Follow it or your manual.
Clamp-style wheel: remove the clamp screw and the front half of the clamp, then slide the wheel off the shaft.
Tip. Old plastic wheels can be brittle and stuck to the shaft. Use steady pressure. If the old wheel cracks coming off, that is fine, you are replacing it anyway.
- 5
Clean out the housing
Vacuum the lint out of the blower housing and the duct leading into it. While you are there, look at the motor shaft for scoring or damage.
Tip. A scored shaft, or a motor that grinds when you turn it, points to a bad motor, not just a bad wheel.
- 6
Match the new wheel
Hold the old and new wheels side by side. The diameter, the blade shape and the hub (threaded or clamp style) should match. Check that it lists your dryer's model number.
Buy the part
Blower wheel
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- A wheel listed for your dryer's model number, from the rating plate.
- The same hub type as the old one: threaded onto the shaft, or held with a clamp.
- The same diameter and blade shape.
If you are also replacing the drive motor and the old wheel is stuck on the shaft, buy a new wheel with the motor.
- 7
Fit the new wheel
Threaded wheel: thread it on the opposite way to how the old one came off, hold the shaft and snug it with the wrenches. Clamp-style wheel: slide it on, line up the clamp and tighten the screw.
Spin the wheel by hand a few times. It should be tight on the shaft and turn without rubbing the housing.
- 8
Close everything up
Refit the housing cover or lint duct and its seals. If you took the drum out, set it back on its rear rollers and route the belt around the idler and motor pulley as in your photo.
Refit the front panel, reconnect the door switch wires and close the top.
- 9
Power up and check the airflow
On a gas dryer, turn the gas shutoff handle back in line with the pipe. Plug the dryer in and run a heated cycle.
Feel the vent hood outside. You should get a strong, steady stream of warm air.
Buy the part
Get the right replacement
Buy the part
Blower wheel
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- A wheel listed for your dryer's model number, from the rating plate.
- The same hub type as the old one: threaded onto the shaft, or held with a clamp.
- The same diameter and blade shape.
If you are also replacing the drive motor and the old wheel is stuck on the shaft, buy a new wheel with the motor.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas. Do not touch any switches. Leave the house and call your gas utility from outside.
- The job would mean disconnecting or moving the gas line. Leave gas connections to a pro.
- The motor shaft is scored, or the motor grinds or will not turn. That is a drive motor job.
- You see scorch marks, melted plastic or a burnt smell inside the cabinet.
FAQ
Blower wheel questions
How do I know it is the blower wheel and not the vent?
Check the vent first. It is the easier fix. Clean the lint screen and the exhaust vent. If airflow at the outside hood is still weak, the blower wheel is the next suspect.
Which way does the blower wheel unscrew?
On many dryers it is reverse threaded, so it loosens clockwise while you hold the motor shaft still. Many wheels have an arrow marking the direction. When in doubt, follow your service manual.
Can I just clean the blower wheel?
If it is only packed with lint and the blades and hub are sound, yes. Cleaning it restores airflow. A cracked, broken or loose wheel needs replacing.
Related
Keep going
- SymptomDryer takes too long to dryLoads need two cycles, or come out damp. On gas and electric dryers alike, the usual cause is restricted airflow: a clogged lint screen, a blocked vent or a crushed duct. Load size matters too.Open guide
- SymptomDryer squealing, squeaking or thumpingA squeal or squeak usually comes from the idler pulley or a motor bearing. A rhythmic thump usually comes from worn drum rollers, drum glides or a damaged belt. A rattle or knock can be the blower wheel.Open guide
- Dryer partExhaust vent and ductThe exhaust duct carries hot, damp air and lint from the back of the dryer to a hood outside. When lint packs into it, drying slows and the dryer runs hot. Gas and electric dryers both need it cleaned about once a year.Open guide
- Dryer partLint screenThe lint screen catches fluff before it reaches the vent. A clogged or coated screen slows drying and makes the dryer run hot. Gas and electric dryers both have one, and cleaning it takes a minute.Open guide
- Dryer partDrive motorThe drive motor turns the drum through the belt and, on many dryers, spins the blower fan too. It is one of the bigger dryer repairs. Gas and electric dryers both have one.Open guide
