Dryer drum roller replacement
A thump-thump-thump that keeps time with the drum is usually a worn roller. New rollers are cheap and the job is mostly lifting the drum out.
- Difficulty
- Moderate
- Time
- 45 min–3 hr
- Typical part cost
- $15–$60Pro: $50–$250
- Tools
- 4See the list
The rollers come off with a clip. Most of the job is opening the cabinet, freeing the belt and lifting the drum out and back.
What it does
What the rollers does
The drum is heavy, and it has to turn smoothly for hours. Small rubber or plastic wheels on short shafts hold it up while it turns. Many dryers have two of them at the back of the drum.
The front of the drum is held up in different ways. Many dryers use felt or plastic glides on the front panel. Others have a second pair of rollers at the front. Your service manual or tech sheet shows which you have.
Gas and electric dryers use the same kind of rollers.
Why it fails
Every turn of the drum rolls on these wheels. Over the years the bearing inside wears, and the wheel squeaks, scrapes or rumbles.
The wheels can also wear flat spots. Each flat spot makes a thump once per drum turn. A dryer that sits unused for a long time can flat-spot its rollers too.
A badly worn roller can drag or seize, which makes the drum hard to turn.
Symptoms
Signs of a bad rollers
A rhythmic thump
A steady thump-thump that speeds up and slows down with the drum usually means a roller with a flat spot.
Full diagnosisSqueaking or scraping from the back
A worn roller bearing squeaks, scrapes or rumbles, often from the rear of the dryer.
Full diagnosisDrum is hard to turn
A dragging or seized roller makes the drum stiff or bumpy to turn by hand, and can stall it.
Full diagnosis
How to test it
Test the rollers before you buy
- Unplug the dryer.
- Open the door and turn the drum slowly by hand through a few full turns. Listen and feel.
The belt adds a little drag. That is normal. Bumps or a thump at the same spot each turn are not.
- Good
- Smooth, quiet and even all the way around.
- Bad
- Bumps, thumps, rumbling or squeaking with the motor off. The rollers are likely worn.
- With the dryer unplugged and the drum out (see the steps below), find the rollers.
- Spin each one with your fingers and rock it on its shaft. Look closely at the rolling surface.
- Good
- Each roller spins freely and quietly, with no wobble, cracks or flat spots.
- Bad
- Rough, noisy, wobbly, cracked or flat-spotted. Replace the rollers as a set.
Safety first
Before you touch anything
- 1
Unplug the dryer
Pull the power cord from the wall. If you cannot reach the plug, turn off the dryer's breaker. Do this before you take off any panel.
- 2
Gas dryers: close the gas shutoff
Turn the shutoff handle on the gas line behind the dryer a quarter turn so it sits crosswise to the pipe. You will not open any gas fittings. If you pull the dryer out, move it gently so you do not kink or strain the gas line.
- 3
Wear gloves
The sheet metal edges inside a dryer cabinet can be sharp, and the drum is bulky to lift.
- 4
Let it cool
If the dryer just ran, let it cool before you reach in.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexMany dryer panel screws are 1/4 in. hex heads.Typically $6–$15Shop this tool
- Nut driver5/16 in. hexThe other common panel screw size. Your dryer may use one or both.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareA flat blade pries the roller's retaining clip off its shaft.Typically $10–$25Shop this tool
- Socket set1/4 in. drive, with extensionOptionalFor the nut that holds a roller shaft, if you replace the shafts too. Sizes vary by model.Typically $20–$45Shop this tool
- Work glovesDryer cabinet edges can be sharp.Typically $8–$20Shop this tool
- Shop vacuumOptionalClears the lint that piles up inside the cabinet once the drum is out.Typically $40–$90Shop this tool
Step by step
How to replace the rollers
- 1
Unplug the dryer and close the gas
Pull the power cord from the wall, or turn off the dryer's breaker if you cannot reach the plug.
On a gas dryer, also turn the gas shutoff handle a quarter turn so it sits crosswise to the pipe.
Careful. If you slide the dryer out, move it gently. Do not kink or strain the gas line, and never disconnect it yourself.
- 2
Open the cabinet
On many dryers you open or remove the top, then take off the front panel. Label and unplug the door switch wires before the front panel comes away.
Dryers differ, so check your dryer's service manual or tech sheet for the order on your model.
Tip. Take photos at every stage. They make putting it back together much easier.
- 3
Free the belt and lift the drum out
Photograph the belt path. Reach under the drum, push the idler pulley to slacken the belt and slip the belt off the motor pulley. Let the idler back slowly.
Lift the drum slightly and slide it out through the front, with the belt still around it.
Careful. The idler is under spring tension. Keep hold of it so it does not snap back on your fingers.
- 4
Take the old rollers off
Each roller is held on its shaft by a small retaining clip or washer. Pry it off with a flat screwdriver, then slide the roller off the shaft.
If your kit includes new shafts, or a shaft is worn or loose, it comes out by removing the nut that holds it to the cabinet. Where that nut sits and its size depend on the model, so check your service manual.
Tip. The clips like to fly. Hold a gloved finger over the clip as you pry it.
- 5
Match the new rollers
Replace all the rollers as a set, not just the noisy one, so the drum sits evenly. Check that they list your dryer's model number.
If your dryer has front glides and they are worn thin, now is a good time to replace them too.
Buy the part
Drum support rollers
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- Rollers listed for your dryer's model number, from the rating plate.
- Enough for every roller your dryer has. Many kits include two rollers, shafts and clips.
- If the idler and belt are also worn, a kit with all of them saves a second teardown.
Repair kits that bundle rollers with an idler pulley and belt are common and often cheap. Only buy one that lists your model.
- 6
Fit the new rollers
Slide each new roller onto its shaft and push it fully home. Fit a new retaining clip so it seats firmly in the groove.
Spin each roller. It should turn freely without wobbling.
Careful. A roller that is not pushed fully onto its shaft will keep thumping. Check each one.
- 7
Set the drum back and route the belt
Slide the drum back in and set its back edge onto the rollers. Reach under, push the idler to make slack, and loop the belt around the idler and the motor pulley as in your photo.
Turn the drum by hand a few times. It should feel smooth, and the belt should stay centered.
- 8
Close up and test
Refit the front panel and reconnect the door switch wires using your labels. Close the top.
On a gas dryer, turn the gas shutoff handle back in line with the pipe. Plug the dryer in and run a short cycle. The thumping should be gone.
Buy the part
Get the right replacement
Buy the part
Drum support rollers
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- Rollers listed for your dryer's model number, from the rating plate.
- Enough for every roller your dryer has. Many kits include two rollers, shafts and clips.
- If the idler and belt are also worn, a kit with all of them saves a second teardown.
Repair kits that bundle rollers with an idler pulley and belt are common and often cheap. Only buy one that lists your model.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas. Do not touch any switches. Leave the house and call your gas utility from outside.
- The job would mean disconnecting or moving the gas line. Leave gas connections to a pro.
- A roller shaft is broken off or its mount in the cabinet is cracked.
- The noise is still there with new rollers, idler and belt. The motor or blower may be the cause.
- You see scorch marks, melted wires or a burnt smell inside the cabinet.
FAQ
Drum support rollers questions
Should I replace all the rollers or just the bad one?
All of them. Replacing them as a set keeps the drum sitting evenly, and the others are usually close behind.
Is the thump the rollers or the belt?
Usually the rollers. A flat-spotted roller thumps once per drum turn. A belt with a flat spot can thump too, but it is less common. Spin the drum by hand to tell. Worn rollers feel bumpy even with the motor off.
Should I replace the idler pulley while I am in there?
It is worth it if it is rough or noisy. The idler pulley and rollers wear together, and the drum is already out.
Related
Keep going
- SymptomDryer squealing, squeaking or thumpingA squeal or squeak usually comes from the idler pulley or a motor bearing. A rhythmic thump usually comes from worn drum rollers, drum glides or a damaged belt. A rattle or knock can be the blower wheel.Open guide
- SymptomDryer runs but won't tumbleThe dryer starts and the motor runs, but the drum stays still or barely moves. The usual cause is a broken drum belt, then the idler pulley that keeps it tight, then worn drum rollers.Open guide
- Dryer partIdler pulleyThe idler pulley is a small spring-loaded wheel that keeps the drum belt tight. When its bearing wears, it squeals. Gas and electric dryers both have one.Open guide
- Dryer partDrum beltThe drum belt wraps around the drum and the motor pulley and turns the drum. When it breaks, the drum stops tumbling. Gas and electric dryers both have one, and the swap is the same on both.Open guide
- Dryer partBlower wheelThe blower wheel is the fan that pulls air through the drum and pushes it out the vent. A cracked, loose or lint-packed wheel means slow drying and odd noises. Gas and electric dryers both have one.Open guide
