WhatsBusted
3D model of an idler pulley
Also called dryer idler pulley, belt tensioner

Dryer idler pulley replacement

That squeal at the start of every load is often a tired idler pulley. It is a small, cheap part, and you reach it the same way you reach the belt.

Difficulty
Moderate
Time
30 min–1.5 hr
Typical part cost
$8–$30Pro: $90–$250

The part is simple. The work is getting to it: opening the cabinet and, on many dryers, taking the belt off and lifting the drum out.

What it does

What the idler does

The idler pulley is a small wheel on a spring-loaded arm, down under the drum near the motor. It pushes on the drum belt to keep it tight so the belt grips the motor pulley instead of slipping.

On many dryers the idler arm pivots on the motor's mounting bracket, and a spring pulls it against the belt.

Gas and electric dryers use the same kind of idler. On many dryers a small belt switch sits right by it and stops the motor if the belt breaks.

Why it fails

The wheel spins on a small bearing every minute the drum turns. Over years the bearing dries out and wears, and it starts to squeal, then grind.

The wheel can also crack, wobble on its axle, or the arm can wear or bind, so the belt slips or comes off.

A seized idler drags on the belt and can wear through even a new belt quickly.

Symptoms

Signs of a bad idler

  • Squealing, worst at start-up

    A high squeal when the dryer starts that may ease as it warms up, and gets louder over weeks, is a classic worn idler sign.

    Full diagnosis
  • Screech or tick from the front

    A screech or a ticking from the front of the dryer can trace back to the idler.

  • Belt slips or comes off

    A weak arm or a wobbling wheel lets the belt slip or ride off the pulleys. The drum may turn slowly, stop, or not turn at all.

    Full diagnosis

How to test it

Test the idler before you buy

1. Spin it by handNo meter needed
  1. Unplug the dryer and open the cabinet so you can reach the idler (see the steps below).
  2. Slip the belt off the idler, or take it off the motor pulley so the idler is free.
  3. Spin the idler wheel with your fingers and rock it side to side.

Do not oil a noisy idler. Oil collects lint and dust and makes it worse. Replace it instead.

Good
Spins freely and quietly, with no wobble, no cracks and a straight axle. It sits in line with the motor pulley.
Bad
Grinds, feels rough, catches, wobbles, or is cracked or chipped. Replace it.
2. Check the arm and springNo meter needed
  1. With the belt off, move the idler arm through its travel by hand.
  2. Look at the spring and the spot where the arm pivots.
Good
The arm pivots smoothly and the spring pulls it back firmly.
Bad
The arm is cracked, worn or binding, or the spring is stretched or broken. Replace the idler assembly and spring.

Safety first

Before you touch anything

  1. 1

    Unplug the dryer

    Pull the power cord from the wall. If you cannot reach the plug, turn off the dryer's breaker. Do this before you take off any panel.

  2. 2

    Gas dryers: close the gas shutoff

    Turn the shutoff handle on the gas line behind the dryer a quarter turn so it sits crosswise to the pipe. You will not open any gas fittings. If you pull the dryer out, move it gently so you do not kink or strain the gas line.

  3. 3

    Wear gloves

    The sheet metal edges inside a dryer cabinet can be sharp.

  4. 4

    Let it cool

    If the dryer just ran, let it cool before you reach in.

Tools you'll need

Grab these first

Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works

See the full repair tool kit

Step by step

How to replace the idler

  1. 1

    Unplug the dryer and close the gas

    Pull the power cord from the wall, or turn off the dryer's breaker if you cannot reach the plug.

    On a gas dryer, also turn the gas shutoff handle a quarter turn so it sits crosswise to the pipe.

    Careful. If you slide the dryer out to reach the back, move it gently. Do not kink or strain the gas line, and never disconnect it yourself.

  2. 2

    Open the cabinet

    How you reach the idler depends on the dryer. On many, you open the top, take off the front panel and work from the front. On some, a rear access panel comes off instead and the idler is right there.

    Check your dryer's service manual or tech sheet for your model. If the front panel comes off, label and unplug the door switch wires first.

    Tip. Take photos at every stage. They make putting it back together much easier.

  3. 3

    Take the belt off the idler

    Photograph how the belt wraps around the idler and the motor pulley. Push the idler to slacken the belt and slip the belt off the motor pulley, then let the idler back slowly.

    If the idler is hard to reach with the drum in place, lift the drum out through the front with the belt still around it.

    Careful. The idler arm is under strong spring tension. Keep hold of it and let it back slowly so it does not snap back on your fingers.

  4. 4

    Remove the old idler

    Unhook the tension spring, noting exactly where each end hooks on. Then lift the idler arm out of its pivot on the motor bracket or the base.

    On some dryers the wheel comes off its axle on its own. On others you replace the whole arm with the wheel. Match what your new part looks like.

  5. 5

    Match the new idler

    Hold the old and new parts side by side. The wheel size, the arm shape and the pivot should match. Check that the part lists your dryer's model number.

    If your kit includes a new spring, use it.

  6. Buy the part

    Idler pulley

    Opens AppliancePartsPros in a new tab. Where’s my model number?

    What to look for

    • An idler listed for your dryer's model number, from the rating plate.
    • The same style as the old one: just the wheel, or the whole arm with the wheel. Some come with a new spring.
    • If the belt and rollers are also worn, a kit with all three can save a second teardown.

    Repair kits that bundle the idler with a belt and drum rollers are common and often cheap. Only buy one that lists your model.

  7. 6

    Install the new idler

    Set the arm into the same pivot and hook the spring back on exactly as the old one was.

    Move the arm by hand. It should swing freely and the spring should pull it back firmly.

  8. 7

    Put the belt back on

    If you took the drum out, set it back on its rear rollers first. Push the idler to make slack, loop the belt around the idler and then the motor pulley as in your photo, and let the idler back slowly.

    Turn the drum by hand a few times. The belt should stay centered on the idler and the motor pulley.

  9. 8

    Close up and test

    Refit the panels and reconnect the door switch wires using your labels.

    On a gas dryer, turn the gas shutoff handle back in line with the pipe. Plug the dryer in and run a short cycle. The squeal should be gone.

Buy the part

Get the right replacement

Buy the part

Idler pulley

Opens AppliancePartsPros in a new tab. Where’s my model number?

What to look for

  • An idler listed for your dryer's model number, from the rating plate.
  • The same style as the old one: just the wheel, or the whole arm with the wheel. Some come with a new spring.
  • If the belt and rollers are also worn, a kit with all three can save a second teardown.

Repair kits that bundle the idler with a belt and drum rollers are common and often cheap. Only buy one that lists your model.

Know your limits

When to call a pro

Stop and call a pro if

  • You smell gas. Do not touch any switches. Leave the house and call your gas utility from outside.
  • Reaching the idler would mean disconnecting or moving the gas line. Leave gas connections to a pro.
  • The squeal or grinding is still there with a new idler and belt. The rollers or the motor may be the cause.
  • You see scorch marks, melted wires or a burnt smell inside the cabinet.

FAQ

Idler pulley questions

Is it the idler pulley or the drum rollers?

A squeal that is loudest at start-up often points to the idler. A steady thump once per drum turn points more to the drum support rollers. With the belt off, spin each by hand. The rough one is your culprit.

Can I just oil the idler pulley?

Not a good idea. Oil collects lint and dust and makes the bearing worse. A new idler is cheap and lasts far longer.

Should I replace the belt at the same time?

If the belt is cracked, frayed or glazed, yes. You already have it off, and parts that wear together are often replaced together.

Related

Keep going