Hot water runs out fast, or is only lukewarm
Some hot water is good news. The heater is working, just not at full strength, and the reason is usually one of a short list.
Check these first
Five-minute checks, no tools
Check the temperature setting
A setting that is too low is a common cause. On a gas heater, look at the dial on the control at the front. On an electric heater the dials are behind the access panels, so turn the breaker off first. Around 120°F suits most homes.
Notice how it fails
Hot for a few minutes, then cold, points one way. Never more than lukewarm, even first thing in the morning, points another. The questions below use this.
Count the hot water use
Back-to-back showers, laundry and the dishwasher all at once can drain any tank. Spread them out for a day and see if the problem goes away.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Failed lower heating element (electric)
You get some hot water, but it runs out quickly. The upper element still heats the top of the tank while the bottom stays cold. A meter test with the power off tells you.
Fix the element1 hr–3 hr$10–$60 - 2DIY fix
Failed lower thermostat (electric)
Same pattern as a bad lower element, but the element tests good. The lower thermostat is not passing power to it.
Fix the thermostat30 min–1 hr$15–$60 - 3DIY fix
Temperature set too low
Someone turned the dial down, or it was set low from the start. Raise it a little at a time, and do not go past what is safe for your household.
- 4DIY fix
Sediment in the tank
Hard water leaves a layer on the tank bottom that cuts capacity and slows heating. Rumbling or popping while it heats is a common clue. A flush through the drain valve clears it.
Fix the drain and flush45 min–2 hr$0 - 5DIY fix
Broken dip tube
The water is warm but never really hot, even after the heater has had all night. Cold water is mixing in at the top instead of being piped to the bottom.
Fix the dip tube1 hr–2 hr$10–$60 - 6DIY fix
Tank too small for your use
More people, a bigger tub, or a heater replaced with a smaller one can leave the tank undersized. Nothing is broken. A larger tank, or spreading out hot water use, is the answer.
- 7Call a pro
Crossed hot and cold plumbing
A faulty mixing faucet or valve somewhere in the house lets cold water leak into the hot lines. A plumber can find and fix it.
What's happening
What your water heater is doing
Cold water enters through a dip tube that carries it to the bottom of the tank. Hot water leaves from the top. The heater keeps the two apart so you draw hot water first.
On an electric heater, the upper element heats the top of the tank and the lower element heats the rest. If the lower element or lower thermostat fails, the top still gets hot, so you get a short burst of hot water that runs out quickly.
If the dip tube cracks or breaks off, incoming cold water mixes with the hot water at the top. Then the water is warm instead of hot, on gas and electric heaters alike.
Sediment from hard water settles on the bottom of the tank. It takes up space and slows the heat getting into the water, so the heater recovers more slowly.
Sometimes nothing is broken. A household that grew, a new big tub or several showers in a row can outrun a tank that was sized for less.
Know your limits
When to call a pro
Stop and call a pro if
- The crossed-plumbing check shows cold water still flowing from a hot tap with the heater's cold supply closed.
- Your heater is gas and raising the dial does not help.
- You think the tank is too small and want help sizing a replacement.
- You are not comfortable testing a 240 V circuit with a meter.
FAQ
Common questions
Why does my hot water run out so fast?
On an electric heater, a failed lower element or lower thermostat is a likely cause: only the top of the tank heats. On any heater, sediment, a broken dip tube or simply more demand than the tank can handle will do it too.
What temperature should my water heater be set to?
About 120°F suits most homes. It is hot enough for showers and dishes and lowers the risk of scalds. See water too hot for how to check it at the tap.
How do I know if my dip tube is broken?
There is no simple outside test. The classic sign is water that is warm but never hot. Checking it means shutting off the water, relieving pressure and pulling the tube out of the cold inlet to look for cracks.
Will flushing the tank help?
If sediment is the cause, yes. A flush through the drain valve clears the layer on the bottom. One manufacturer suggests flushing about once a year, or more often with hard water.
Related
Keep going
- SymptomWater heater not heating: no hot waterEvery hot tap runs cold. On an electric heater it is usually power, a tripped high-limit reset, an element or a thermostat. On a gas heater, start with the gas supply and the pilot.Open guide
- SymptomWater heater rumbling or poppingA rumbling, popping or crackling tank usually means sediment has built up on the bottom. On electric heaters, scale on the lower element can do it too. Flushing the tank is the usual fix.Open guide
- SymptomWater heater making water too hotHot water comes out hotter than it should. Check the setting and measure at a tap. If it stays too hot after you turn it down, a thermostat or gas control has likely failed.Open guide
- Water heater partHeating elementElectric water heaters only. Two heating elements, one upper and one lower, heat the water. A burned-out element is the most common reason an electric water heater stops making hot water, and both test and replace the same way.Open guide
- Water heater partWater heater thermostatElectric water heaters only. Two thermostats decide which element heats and when. The upper one also carries the red reset button, a safety cutoff that shuts everything off if the water gets too hot.Open guide
- Water heater partDip tubeThe dip tube carries cold water to the bottom of the tank. When it cracks or breaks, cold water mixes with the hot at the top and you run out fast. Gas and electric tanks both have one.Open guide
- Water heater partDrain valve and tank flushThe drain valve near the bottom of the tank lets you empty it and flush out sediment. Manufacturers suggest flushing gas and electric tanks about once a year, more often with hard water.Open guide