Hot water too hot? Turn it down, then find out why
Water that is too hot is a burn risk, not just an annoyance. The fix is often a dial, but if the water stays hot after you turn it down, a control has failed.
Check these first
Five-minute checks, no tools
Measure at the tap
Hold a kitchen thermometer in the stream at the tap nearest the heater. Check first thing in the morning, or at least two hours after anyone used hot water.
Check the setting
On a gas heater, look at the dial on the front control. On an electric heater, turn the breaker off before you open the access panels to see the thermostats. The dial is a rough guide, so trust the thermometer.
Turn it down and recheck
Lower the setting per the manual, give the heater a full heating cycle, then measure again. Repeat until the tap reads about 120°F.
Look at the relief valve pipe
Check the pipe running down from the valve near the top of the tank. If water or steam is coming out, do not cap or plug it. Call a pro.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Temperature set too high
The water got hotter after someone turned the dial up, or it has always been hot. Turning it down and rechecking with a thermometer fixes it.
- 2DIY fix
Stuck or failed thermostat (electric)
The water stays too hot after you turn the dial down, or the high-limit reset keeps tripping. A thermostat that sticks on keeps the element heating past the setting.
Fix the thermostat30 min–1 hr$15–$60 - 3Call a pro
Gas control valve (gas)
On a gas heater the thermostat is built into the gas control valve. If turning the dial down does not bring the temperature down, the valve needs a pro.
What's happening
What your water heater is doing
Hot water burns fast. Most adults get a third-degree burn from 150°F water in about two seconds. Even at 120°F, a long exposure can burn. Young children and older adults are hurt most often.
Safety and energy agencies recommend about 120°F for most homes. Some manufacturers set heaters higher at the factory.
A thermostat switches the heat off when the water reaches the setting. If it sticks on, the heat keeps going. On an electric heater, the high-limit switch above the upper thermostat should then cut the power, so overheating often shows up as the reset tripping. On a gas heater, the thermostat is built into the gas control valve near the bottom of the tank.
Last in line is the temperature and pressure relief valve near the top of the tank. It opens and dumps water when the tank gets dangerously hot or the pressure climbs too high. If it is releasing water, treat that as a warning, not a nuisance.
Know your limits
When to call a pro
Stop and call a pro if
- The temperature and pressure relief valve is releasing water or steam. Do not cap or plug it.
- The water stays too hot after you turn the setting down.
- An electric heater's high-limit reset keeps tripping.
- You hear boiling or loud rumbling from the tank.
- You smell gas. Leave the house and call your gas utility from outside.
FAQ
Common questions
What temperature should a water heater be set at?
About 120°F for most homes. That cuts the risk of scalds and saves energy compared with higher settings. Check your manual, since some households have reasons to run hotter.
Why is my water so hot even on a low setting?
The dial is only a rough guide, so measure at a tap first. If the water is still well above the setting after a full heating cycle, the thermostat, or the gas control valve on a gas heater, is likely not shutting off.
Is water coming out of the relief valve dangerous?
It means the tank went over a safe temperature or pressure, or the valve itself is faulty. High pressure from water expanding in a closed system is one common reason. Do not cap the pipe. Have a pro find the cause.
Related
Keep going
- SymptomWater heater not heating: no hot waterEvery hot tap runs cold. On an electric heater it is usually power, a tripped high-limit reset, an element or a thermostat. On a gas heater, start with the gas supply and the pilot.Open guide
- SymptomWater heater not making enough hot waterThe shower starts hot and goes cold too soon, or the water is never more than warm. Check the temperature setting first, then the lower element and thermostat on electric units, the dip tube and sediment.Open guide
- SymptomWater heater leakingWater on the floor or dripping down the tank. Shut off the power or gas and the cold supply, dry everything, then trace the water to its source: a valve, a fitting, an element gasket, or the tank itself.Open guide
- Water heater partWater heater thermostatElectric water heaters only. Two thermostats decide which element heats and when. The upper one also carries the red reset button, a safety cutoff that shuts everything off if the water gets too hot.Open guide
- Water heater partTemperature and pressure relief valveThe T&P relief valve opens to let water out if the tank gets too hot or the pressure gets too high. Gas and electric heaters both have one. Test it once a year by lifting its lever.Open guide
- Water heater partGas control valveGas water heaters only. The gas control valve is the heater's thermostat and gas valve in one. It decides when gas reaches the burner and shuts it off if something is wrong. Testing or replacing it is pro work.Open guide