WhatsBusted
Symptom

No hot water from your water heater

Stone cold at every tap usually means one thing upstream has stopped, not that the whole tank is done. Start with the easy checks.

Check these first

Five-minute checks, no tools

  • Cold at every hot tap

    Run the hot water at two or three faucets. If only one is cold, the problem is that faucet or its valve, not the water heater.

  • Breaker on (electric)

    Find the water heater's breaker in the panel. If it has tripped, switch it fully off, then back on. If it trips again right away, leave it off and see [breaker keeps tripping](/water-heater/symptoms/tripping-breaker).

  • High-limit reset (electric)

    With the breaker off, remove the upper access panel and press the red reset button firmly. Close the panel before you turn the power back on. Do this once. If it trips again, something is making the water overheat.

  • Gas shutoff open (gas)

    The handle on the gas line to the heater should sit in line with the pipe. Crosswise means closed. Check that another gas appliance, like the stove, works.

  • Pilot lit (gas)

    Look through the small window near the bottom of the tank for the pilot flame. If it is out and you do not smell gas, relight it by following the lighting instructions on the heater's label exactly.

Likely causes

Ranked by how often they are the problem

  1. 1

    Burned-out heating element (electric)

    DIY fix

    Power is on and the reset has not tripped, but the water stays cold. A failed upper element leaves the whole tank cold. Elements can be tested with a multimeter once the power is off.

    Fix the element1 hr–3 hr$10–$60
  2. 2

    Tripped high-limit reset (electric)

    DIY fix

    The red button above the upper thermostat cut the power because the water got too hot. Resetting it once, with the breaker off, is fine. If it trips again, something is making the water overheat, often a thermostat or element, and a pro should find the cause.

    Fix the thermostat30 min–1 hr$15–$60
  3. 3

    Failed upper thermostat (electric)

    DIY fix

    The elements test good but never get power, or the reset keeps tripping. The upper thermostat controls both elements, so when it fails nothing heats.

    Fix the thermostat30 min–1 hr$15–$60
  4. 4

    No power to the heater (electric)

    DIY fix

    A tripped breaker is one of the most common reasons an electric heater stops heating. A breaker that trips again right after you reset it points to a short, so leave it off.

  5. 5

    Thermocouple (gas)

    Call a pro

    The pilot lights but goes out as soon as you let go of the control knob. The thermocouple is not sensing the flame, so the gas valve shuts. This is gas work for a pro.

  6. 6

    Pilot out (gas)

    Call a pro

    No pilot flame. Relight it once by following the lighting instructions on the label. If it will not light or will not stay lit, see pilot won't stay lit and call a pro.

  7. 7

    Gas control valve (gas)

    Call a pro

    The pilot stays lit but the burner never comes on, or a tech has already ruled out the thermocouple. The valve may not be opening. Gas valve work is for a pro.

  8. 8

    Gas supply off or interrupted (gas)

    Call a pro

    The shutoff on the heater's gas line is closed, or other gas appliances in the house have stopped too. If you know it was closed by mistake, open it and relight the pilot by the label. If you are not sure why it was closed, or the whole house has no gas, call your gas utility.

What's happening

What your water heater is doing

An electric water heater has two elements and two thermostats. The upper thermostat heats the top of the tank first, then hands power to the lower one. Above the upper thermostat sits a high-limit switch with a red reset button that cuts all power if the water gets too hot.

Cold water at every tap on an electric heater means power is not getting to the elements, the high limit has tripped, or the upper element or upper thermostat has failed. When the upper side fails, the whole tank goes cold, because the lower side never gets its turn.

A gas water heater burns gas under the tank. A small pilot flame lights the burner, and the gas control valve near the bottom of the tank only opens the main gas while it senses that pilot. If the pilot is out or gas is not reaching the heater, the burner never comes on.

Not sure which kind you have? A gas heater has a vent pipe on top and a control knob with a dial on the front, low down. An electric heater has a thick cable running into the top and two small covered panels on the side.

If you get some hot water but it runs out fast, see not enough hot water instead.

Know your limits

When to call a pro

Stop and call a pro if

  • You smell gas. Do not light anything or touch any switches. Leave the house and call your gas utility from outside.
  • A gas heater's pilot will not light, or will not stay lit after you follow the label instructions.
  • The high-limit reset trips again after you reset it.
  • The breaker trips again as soon as you turn it back on.
  • You are not comfortable testing a 240 V circuit with a meter.

FAQ

Common questions

Where is the reset button on an electric water heater?

Behind the upper access panel on the side of the tank, at the top of the upper thermostat. It is usually red. Turn the breaker off first, take off the panel, and press it firmly until it clicks.

Why does my water heater reset button keep tripping?

The high limit trips when the water gets hotter than it should. Common causes are a thermostat stuck on, a shorted element or a faulty high-limit switch. Manuals say to call a technician if it trips again after a reset, and never to tamper with the button to keep the heater running.

How do I relight the pilot on a gas water heater?

Follow the lighting instructions printed on the label on the front of the heater, step by step. They differ between models. Do not try to light it if you smell gas.

How long does it take to get hot water back?

A tank that went fully cold has to reheat from the start, so give it time before you judge the fix. Check one tap after a while rather than running every faucet at once.

Related

Keep going