WhatsBusted
3D model of a pilot assembly
Call a proAlso called water heater pilot, pilot light

Water heater pilot assembly: signs of trouble and when to call a pro

The pilot is the small flame that lights the main burner. If it is weak, yellow or keeps going out, the pilot assembly may need a pro's attention.

Who fixes it
A licensed pro
Typical pro cost
$100–$400
Typical estimate: about a thermocouple job plus a pricier part. Get a local quote

Gas and combustion work. The pilot sits in a sealed burner chamber on most modern heaters. Reaching it means disconnecting gas tubes, removing the burner and replacing the door gasket. Pros only.

What it does

What the pilot does

Gas water heaters only. The pilot assembly sits next to the main burner, inside the combustion chamber under the tank. It burns a small flame that lights the main burner every time the heater calls for heat.

On most newer heaters it is one unit: the pilot burner, the spark electrode from the push-button igniter, and the thermocouple that proves the flame is there.

A thin gas tube feeds it from the gas control valve. The assembly is matched to the heater model, the gas type and sometimes the altitude.

Why it fails

The pilot has a tiny gas opening that can clog with dust or debris. Then the flame gets small or yellow and may not heat the thermocouple enough to stay lit.

The thermocouple built into the assembly wears out with time in the flame. It is the most common reason a pilot will not stay lit.

On newer heaters, a pilot that goes out can also mean the heater is short on combustion air, often from lint clogging the screen at its base. A safety switch then shuts the pilot down on purpose.

Symptoms

Signs the pilot is failing

  • Pilot will not stay lit

    You follow the lighting instructions on the label and the pilot lights, but it goes out when you release the knob or soon after. If it fails after several tries, turn the control to OFF and call a pro.

    Full diagnosis
  • Small or mostly yellow pilot flame

    A healthy pilot flame is mostly blue. A tiny, weak or mostly yellow flame points to a dirty pilot opening.

  • Igniter clicks but no pilot

    You press the igniter button as the label says and see sparks or hear clicks, but no pilot flame appears. The pilot opening may be blocked, or gas may not be reaching it. Stop after a few tries and call a pro.

  • Pilot goes out while the burner runs

    The pilot holds, then drops out a few minutes after the main burner lights. That can be a worn pilot assembly or a heater short on combustion air.

    Full diagnosis

Safety first

Stay safe until it is fixed

  1. 1

    Smell gas? Leave first

    Do not try to light the pilot, touch electrical switches or use a phone inside. Leave the house right away and call your gas utility from outside or a neighbor's phone.

  2. 2

    CO alarm going off? Get out

    Get everyone, pets included, outside into fresh air and call 911. Do not go back in until emergency responders say it is safe.

  3. 3

    Turn the control to OFF and leave it

    If the pilot will not light or stay lit after a few tries per the label, turn the gas control knob to OFF as the label shows and call for service. Do not open the burner chamber.

What a pro does

What to expect from the service call

  • Look at the pilot flame and check that the heater is getting enough combustion air, including the screen at the base.
  • Check whether the problem is the pilot opening, the igniter, the thermocouple or the gas control behind them.
  • If the pilot is at fault, shut off the gas and clean it or fit a new pilot assembly matched to the heater, its gas type and altitude, following the heater maker's service instructions.
  • Check every gas connection they touched for leaks, relight per the label and watch the pilot and burner through a full cycle.

Know your limits

When to call a pro

Stop and call a pro if

  • You smell gas at any point. Leave the house and call your gas utility from outside.
  • The pilot will not light or will not stay lit after following the label instructions a few times.
  • The pilot flame is small, weak or mostly yellow.
  • The pilot keeps going out, or goes out while the burner runs.
  • The area around the burner or the screen at the base of the heater looks scorched or discolored. Leave it off; a pro decides whether the heater can be repaired.

FAQ

Pilot assembly questions

Can I relight my water heater pilot myself?

Yes. Relighting is normal owner operation. Follow the lighting instructions on the label on your heater exactly, and only if you do not smell gas. If the pilot will not stay lit after a few tries, turn the control to OFF and call a pro.

Can I clean or replace the pilot assembly myself?

Not on most modern heaters. The pilot sits in a sealed chamber, and getting to it means disconnecting gas tubes and removing the burner. The replacement kit even comes with a new door gasket because the old one cannot be reused. That is pro work.

Why does my pilot keep going out?

The usual causes are a worn thermocouple, a dirty pilot opening, or a heater that is short on combustion air. Lint at the base can trip a safety switch that shuts the pilot down. See pilot won't stay lit for the full list.

How much does a pilot assembly replacement cost?

On most newer heaters the thermocouple is part of the pilot assembly, so it is about the same job with a pricier part. Expect a few hundred dollars with a pro, part included. We found no published price for this exact job, so get a quote for your area.

Related

Keep going