Water heater leaking? Find where it is coming from
A puddle under the tank does not always mean a dead tank. Many leaks come from a fitting or valve you can fix. Find the source before you decide anything.
Check these first
Five-minute checks, no tools
Power or gas off, then cold water off
Electric: turn off the heater's breaker. Gas: turn the control to OFF per the label. Then close the cold supply valve above the tank. If you smell gas, leave the house and call your gas utility from outside.
Dry it and trace it
Wipe the tank, pipes and floor dry. Check each threaded joint, the valves and the element covers with a dry paper towel to find where the water starts.
Drain valve fully closed
A drain valve that was left slightly open will drip. Turn it closed by hand. Do not force it.
New gas heater? It may be condensation
A gas heater full of cold water can drip and sizzle on the burner while it heats. That is condensation, and it should stop once the tank is hot.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Loose or leaking pipe connections
Water at the hot or cold pipe fittings on top of the tank. A gentle snugging can stop a drip, but do not overtighten. A threaded joint that keeps dripping usually has to come apart and be resealed.
- 2DIY fix
Drain valve
Drips from the spout or the stem of the valve near the bottom. It may be slightly open, or worn. A valve that will not close properly needs replacing.
Fix the drain and flush45 min–2 hr$0 - 3DIY fix
Relief valve or its discharge pipe
Water from the valve near the top, or from the pipe that runs down from it. The tank may be too hot or under too much pressure, often from water expanding in a closed system, or the valve itself is worn. Never cap or plug it. If it keeps dripping, a pro replaces the valve and finds the cause.
Fix the t&p relief valve5–15 min$0 - 4DIY fix
Heating element gasket (electric)
Water behind an element access cover, where the element threads into the tank. The element has worked loose or its gasket has failed. With the power off, snugging the element can stop it. If not, drain the tank below the element and fit a new gasket or element.
Fix the element1 hr–3 hr$10–$60 - 5Call a pro
Leaking tank
Every fitting and valve is dry, but water still pools under the tank, often with rust. The steel tank has corroded through. It cannot be repaired, so the heater needs replacing.
- 6DIY fix
Condensation (gas)
A new gas heater, or one refilled with cold water, drips or sizzles while it heats, then stops once the tank is hot. Nothing is broken. If it keeps happening on a hot tank, have a pro look at it.
What's happening
What your water heater is doing
First, stop the water and cut the power or gas. On an electric heater, turn off its breaker. On a gas heater, turn the control knob to OFF as the label describes. Then close the cold water valve on the pipe going into the top of the tank.
Water runs downhill, so a leak at the top can look like a leak at the bottom. Dry the tank, the floor and every fitting, then watch, or wipe each joint with a dry paper towel, to see where the water shows up first.
Most leaks come from connections and valves, not from the tank. The usual places are the hot and cold pipe connections on top, the temperature and pressure relief valve and its discharge pipe, and the drain valve near the bottom. On an electric heater, also check around the element covers.
If water is coming out of the steel tank itself, usually from rust at the bottom, it cannot be repaired. The heater needs to be replaced.
Know your limits
When to call a pro
Stop and call a pro if
- The relief valve keeps releasing water. Do not cap or plug it.
- The tank itself is leaking. Plan on a replacement.
- A gas heater is leaking near the burner or the gas line.
- You smell gas. Leave the house and call your gas utility from outside.
- A gas heater keeps dripping long after the tank is hot.
FAQ
Common questions
Can a leaking water heater tank be repaired?
Not if the water is coming from the tank itself. Once the steel has corroded through, the heater needs replacing. Check every fitting and valve first, because those leaks are usually fixable and often look like a tank leak.
Why is my new gas water heater dripping?
When the tank is full of cold water, moisture in the burner's exhaust condenses on the cold tank and drips, sometimes sizzling on the burner. It should stop once the water is hot. If it does not, call a pro.
Why is my relief valve leaking?
Either the tank is getting too hot or the pressure is too high, often from water expanding with no room to go, or the valve itself is worn. High house water pressure can cause it too. Have a pro find the cause, and never cap the valve.
Is it safe to use the water heater while it leaks?
Shut it down while you find the leak: power or gas off, and the cold supply closed. A slow drip from a fitting is not an emergency, but water near an electric heater's wiring or a gas burner is a reason to stop.
Related
Keep going
- SymptomWater heater making water too hotHot water comes out hotter than it should. Check the setting and measure at a tap. If it stays too hot after you turn it down, a thermostat or gas control has likely failed.Open guide
- SymptomWater heater rumbling or poppingA rumbling, popping or crackling tank usually means sediment has built up on the bottom. On electric heaters, scale on the lower element can do it too. Flushing the tank is the usual fix.Open guide
- SymptomWater heater not heating: no hot waterEvery hot tap runs cold. On an electric heater it is usually power, a tripped high-limit reset, an element or a thermostat. On a gas heater, start with the gas supply and the pilot.Open guide
- Water heater partDrain valve and tank flushThe drain valve near the bottom of the tank lets you empty it and flush out sediment. Manufacturers suggest flushing gas and electric tanks about once a year, more often with hard water.Open guide
- Water heater partTemperature and pressure relief valveThe T&P relief valve opens to let water out if the tank gets too hot or the pressure gets too high. Gas and electric heaters both have one. Test it once a year by lifting its lever.Open guide
- Water heater partHeating elementElectric water heaters only. Two heating elements, one upper and one lower, heat the water. A burned-out element is the most common reason an electric water heater stops making hot water, and both test and replace the same way.Open guide
- Water heater partAnode rodThe anode rod wears away on purpose so the steel tank does not rust. Gas and electric tank heaters both have one. Check it every few years and replace it before it is down to the wire.Open guide