Water heater rumbling or popping
That gravelly rumble is usually not a sign of doom. It is most often mineral sediment on the bottom of the tank, and a flush often quiets it.
Check these first
Five-minute checks, no tools
Listen while it heats
Run some hot water so the heater starts heating, then listen. Sediment noise comes while the burner or elements are on and fades when they shut off.
Look for water at the base
Check the floor and the base of the tank for water. A hiss with a puddle is a leak, not sediment. See [water heater leaking](/water-heater/symptoms/leaking).
Check the relief valve pipe
Look at the end of the pipe that runs down from the valve near the top of the tank. If it is dripping or spraying hot water, the tank may be overheating or over pressure. Call a pro.
Gas heater just filled?
A new gas heater, or one just refilled with cold water, often sizzles as condensation drips onto the burner. That is normal and stops once the tank is hot.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Sediment on the tank bottom
The most common cause on both gas and electric heaters. A drain valve flush clears loose sediment and, in many cases, the noise with it.
Fix the drain and flush45 min–2 hr$0 - 2DIY fix
Scale on the lower element
Electric heaters only. Scale on the element makes it rumble, hiss or sizzle while it heats. A scaled element can be removed and cleaned, or replaced. See heating element.
Fix the element1 hr–3 hr$10–$60 - 3DIY fix
Condensation on a cold tank
Gas heaters only. Burning gas makes water vapor that condenses on a cold tank and drips onto the burner with a sizzle. It is common on a new heater filled with cold water, and fades once the tank is hot.
- 4Call a pro
Hardened scale a flush will not clear
After years without flushing, some deposits are too hard or stubborn for a flush to move, and the rumbling stays. A pro can delime the tank with a product made for drinking water systems, or tell you it is time to replace it.
What's happening
What your water heater is doing
Hard water carries dissolved minerals. As the water heats, some of them settle out and collect on the bottom of the tank as sediment and scale.
On a gas heater, the burner heats the tank from underneath. Water trapped under the sediment layer flashes to steam and bubbles up through it. That is the popping and rumbling you hear while the burner runs.
On an electric heater, the lower element sits near the bottom where sediment collects. Scale on the element, or sediment around it, can make it rumble, hiss or sizzle while it heats.
The noise itself does no harm, but the sediment behind it does. Heat has to pass through the layer, so the heater works harder. On electric models, sediment that reaches the lower element can make it fail early.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas. Do not touch any switches. Leave the house and call your gas utility from outside.
- The relief valve or its pipe is dripping or spraying hot water. Never cap or plug it.
- The noise is still there after a full flush.
- Water is pooling around the base of the tank, or dripping keeps going after the tank is hot.
FAQ
Common questions
Is a rumbling water heater dangerous?
Usually not on its own. Sediment noise is a maintenance warning. It costs you efficiency, and on electric models it can shorten element life. The time to worry is if the relief valve starts discharging or water appears at the base. Then call a pro.
Will flushing stop the noise?
In many cases, yes. A flush clears loose sediment. Years of hardened scale may not budge, though. If the noise is the same after a good flush, a pro can delime the tank or help you decide whether it is time to replace it.
How often should I flush my water heater?
Follow your manual first. Without other advice, about once a year is a common rule of thumb, and more often if you have hard water. See drain valve and tank flush for how.
Why does my new gas water heater sizzle?
Burning gas makes water vapor. When the tank is full of cold water, that vapor condenses on the tank and drips onto the burner. It stops once the water is hot. If the dripping keeps going, check for a leak.
Related
Keep going
- SymptomWater heater not making enough hot waterThe shower starts hot and goes cold too soon, or the water is never more than warm. Check the temperature setting first, then the lower element and thermostat on electric units, the dip tube and sediment.Open guide
- SymptomWater heater leakingWater on the floor or dripping down the tank. Shut off the power or gas and the cold supply, dry everything, then trace the water to its source: a valve, a fitting, an element gasket, or the tank itself.Open guide
- Water heater partDrain valve and tank flushThe drain valve near the bottom of the tank lets you empty it and flush out sediment. Manufacturers suggest flushing gas and electric tanks about once a year, more often with hard water.Open guide
- Water heater partHeating elementElectric water heaters only. Two heating elements, one upper and one lower, heat the water. A burned-out element is the most common reason an electric water heater stops making hot water, and both test and replace the same way.Open guide
- Water heater partTemperature and pressure relief valveThe T&P relief valve opens to let water out if the tank gets too hot or the pressure gets too high. Gas and electric heaters both have one. Test it once a year by lifting its lever.Open guide