How to drain and flush a water heater
Good news: this is a garden hose job. An hour or so once a year clears out sediment and lets you check the drain valve while you are there.
- Difficulty
- Easy
- Time
- 45 min–2 hr
- Typical part cost
- $0Pro: $75–$200
- Tools
- 4See the list
No parts and no wiring. The care goes into shutting off the heat first, handling hot water safely and refilling before you turn it back on.
What it does
What the drain and flush does
The drain valve sits near the bottom of the tank, on gas and electric heaters alike. It has a threaded spout that takes a garden hose.
Minerals in the water settle to the bottom of the tank as sediment. Flushing means draining the tank through this valve and running fresh water through it until the water comes out clear.
Why it fails
Skip the flush for years and sediment builds up in the bottom of the tank, which can hurt performance.
The valve itself can drip. Sediment can keep it from closing fully, and older plastic valves can get brittle.
Symptoms
Signs of a bad drain and flush
A year or more since the last flush
Manufacturers suggest flushing about once a year, and some say every six months. Hard water calls for the shorter end.
Sediment when you drain
White specks, grit or cloudy water from the drain valve means sediment has built up. Keep flushing until the water runs clear.
The drain valve drips
Water at the drain spout after it is closed. It may just need to seat again, or the valve may need a new washer or a replacement.
Full diagnosis
How to test it
Test the drain and flush before you buy
- After the flush, close the drain valve firmly by hand and take off the hose.
- Dry the spout with a rag and wait a few minutes.
- Look for water forming at the spout.
- Good
- The spout stays dry. You are done.
- Bad
- It keeps dripping. Open the valve a little and close it again to flush out grit. If that does not stop it, the washer or the whole valve needs replacing.
Safety first
Before you touch anything
- 1
Turn off the power or the gas
Electric heater: turn off its breaker, then hold a voltage tester to the power cable where it enters the heater. Try the tester on a live outlet first. Gas heater: turn the gas control to OFF or PILOT as the label or manual says.
- 2
Close the gas shutoff (gas heaters)
Turn the handle on the gas line to the heater so it sits crosswise to the pipe while you work around the tank. You will not open any gas fittings.
- 3
Let the water cool
Drained water can be hot enough to scald, and an insulated tank stays hot for hours. Give it at least a couple of hours with the heat off, still treat the water as hot, and send it to a drain where it cannot splash anyone.
Wait about 120 min
- 4
Shut off the cold water
Close the cold water supply valve to the heater before you open the drain.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Garden hoseCarries the hot, sandy water from the drain valve to a floor drain or outside.Typically $15–$35Shop this tool
- Non-contact voltage testerPen styleConfirms an electric heater has no power before you drain it.Typically $15–$30Shop this tool
- Bucket5 galCatches the first water so you can see how much sediment comes out.Typically $4–$10Shop this tool
- Work glovesThe valve, the hose fitting and the water can all be hot.Typically $8–$20Shop this tool
- Multi-bit screwdriverPhillips, flat, squareOptionalSome drain valves open with a slotted stem instead of a handle.Typically $10–$25Shop this tool
Step by step
How to drain and flush the tank
- 1
Turn off the power, or the gas
Electric heater: turn off the water heater's breaker. Confirm with a voltage tester at the power cable where it enters the heater.
Gas heater: turn the gas control to OFF or PILOT, as the label or manual says. Then turn the gas shutoff handle on the line so it sits crosswise to the pipe.
Careful. An electric heater must stay off until the tank is full again. A heating element that runs dry can burn out.
- 2
Let it cool, then shut off the cold water
Give the tank time to cool so the water you drain is less likely to scald.
Then close the cold water supply valve on the pipe that feeds the heater.
- 3
Hook up the hose
Screw a garden hose onto the drain valve near the bottom of the tank. Run the other end to a floor drain or outside, somewhere lower than the heater that can take gritty water.
Tip. Lay the hose where nobody will walk past the open end. The first water out is the hottest.
- 4
Open a hot tap
Open a hot water faucet somewhere in the house. That lets air into the tank so it can drain.
- 5
Open the drain valve
Turn the drain valve handle counterclockwise to open it, and let the tank drain.
Watch the water coming out of the hose. White specks and grit are sediment.
Careful. The water can be hot enough to scald, even after cooling. Keep hands and feet clear of the hose end.
- 6
Flush with fresh water
With the drain valve still open, turn the cold supply back on. Fresh water rushes through the tank and carries sediment out of the hose.
Turning the cold supply on and off a few times helps stir up the sediment. Keep going until the water from the hose runs clear.
- 7
If the flow stops
Sediment can plug the drain valve and slow it to a trickle. Close the valve, then open it again to see if the clog clears.
Careful. Do not force a stuck or brittle valve. If it will not move, or looks like it could crack, stop and call a plumber.
- 8
Close the drain valve
Turn the cold supply off, close the drain valve firmly, and take off the hose.
If the spout drips, open the valve a little and close it again to flush out any grit caught in it.
- 9
Refill the tank
Leave the hot faucet open and turn the cold supply back on.
The faucet sputters while air is pushed out. When it runs in a steady stream, the tank is full. Close the faucet.
- 10
Turn the heat back on
Electric heater: only once the tank is full, turn the breaker back on.
Gas heater: open the gas shutoff so the handle lines up with the pipe, then follow the lighting instructions on the heater's label.
Check the drain valve one more time for drips.
Buy the part
Get the right replacement
Buy the part
Drain valve and tank flush
Opens AppliancePartsPros in a new tab. Where’s my model number?
What to look for
- The same thread size and connection type as the old valve. Your heater's parts list has it.
- A valve with a standard garden hose outlet.
Only needed if your drain valve keeps dripping after a flush. Replacement valves are a common part. The tank has to be fully drained before the old one comes out.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas near a gas water heater. Do not touch any switches. Leave the house and call your gas utility from outside.
- The drain valve is stuck, brittle or cracked and will not open or close without force.
- Water keeps leaking from the drain valve or the tank after the flush.
- The drain valve fitting on the tank leaks after you replace the valve.
FAQ
Drain valve and tank flush questions
How often should I flush my water heater?
Manufacturers suggest about once a year for most homes, and every six months if you have hard water. Your heater's manual has its own schedule.
Is the flush the same on gas and electric water heaters?
Yes. The only difference is how you shut the heat off first. Turn off the breaker on an electric heater. On a gas heater, set the gas control as the label or manual says and close the gas shutoff.
My drain valve drips after flushing. What now?
Open it a little and close it again firmly. Grit caught in the seat is a common cause. Some drain valves have a washer behind a hex cap that you can replace after draining the tank.
If it still drips, replacing the valve is a reasonable DIY job. You have to drain the tank completely first.
Why does my electric water heater have to be full before I turn it on?
Electric heating elements need to be under water. Powered in an empty or half-empty tank, they can burn out. Refill until a hot tap runs steady, then turn the breaker on.
Related
Keep going
- SymptomWater heater rumbling or poppingA rumbling, popping or crackling tank usually means sediment has built up on the bottom. On electric heaters, scale on the lower element can do it too. Flushing the tank is the usual fix.Open guide
- SymptomWater heater leakingWater on the floor or dripping down the tank. Shut off the power or gas and the cold supply, dry everything, then trace the water to its source: a valve, a fitting, an element gasket, or the tank itself.Open guide
- SymptomWater heater not making enough hot waterThe shower starts hot and goes cold too soon, or the water is never more than warm. Check the temperature setting first, then the lower element and thermostat on electric units, the dip tube and sediment.Open guide
- Water heater partAnode rodThe anode rod wears away on purpose so the steel tank does not rust. Gas and electric tank heaters both have one. Check it every few years and replace it before it is down to the wire.Open guide
- Water heater partDip tubeThe dip tube carries cold water to the bottom of the tank. When it cracks or breaks, cold water mixes with the hot at the top and you run out fast. Gas and electric tanks both have one.Open guide
- Water heater partTemperature and pressure relief valveThe T&P relief valve opens to let water out if the tank gets too hot or the pressure gets too high. Gas and electric heaters both have one. Test it once a year by lifting its lever.Open guide
