Dishwasher spray arms: clean or replace
Clogged holes in a spray arm leave whole sections of the rack dirty. A toothpick and five minutes usually sorts it out.
- Difficulty
- Anyone can do it
- Time
- 10–45 min
- Typical part cost
- $30–$100Pro: $75–$160
- Tools
- 1See the list
The arms snap or unscrew off by hand on most dishwashers.
What it does
What the spray arms does
Water from the wash pump comes up through the spray arms and out of rows of small holes. The force of the jets is what spins the arms.
Most dishwashers have a lower arm under the bottom rack and a second arm under the upper rack. Some have a third at the top.
Why it fails
Food, seeds, labels and hard-water scale block the holes, so the arm sprays weakly or not at all in places.
An arm can crack, warp or come loose on its hub and stop turning.
A tall pan or utensil that hangs down can stop an arm from turning.
Symptoms
Signs of a bad spray arms
One area stays dirty
Dishes on one rack, or in one corner, come out dirty while the rest are clean.
Full diagnosisArm does not turn
Spin each arm by hand. It should turn freely without catching.
Holes look dark
Hold the arm up to a light. Clear holes let light through; clogged ones look dark.
How to test it
Test the spray arms before you buy
- Switch off the breaker, or unplug the dishwasher. Spin each arm by hand. It should turn freely and not wobble or hit anything.
- Look along the arm for cracks and warping, and at the holes for debris and white scale.
- Good
- Arms spin freely, are straight, and the holes are clear.
- Bad
- An arm catches, wobbles, or has clogged holes. Clean it. A cracked or warped arm needs replacing.
Safety first
Before you touch anything
- 1
Switch it off
Switch off the breaker, or unplug the dishwasher, and let it cool before you reach into the tub.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Stiff nylon brushScrubs scale and grease off the arm.Typically $5–$12Shop this tool
- Needle-nose pliersOptionalPulls seeds and debris out of the holes and the hub.Typically $8–$20Shop this tool
Step by step
How to clean the spray arms
- 1
Switch off and pull the racks
Switch off the dishwasher's breaker, or unplug it under the sink. Pull out the lower rack. For the upper arm, pull out the upper rack too.
- 2
Take the arms off
The lower arm usually pulls straight up, or unscrews from a cap at its center.
The upper arm is often held under the upper rack by a nut or clips. Unscrew the nut by hand, or squeeze the clips, and lower the arm off. Your manual shows which way the nut turns.
- 3
Clear the holes
Rinse each arm under running water. Push a toothpick or a piece of wire into every hole to free debris, then shake and rinse it out.
Soak a scaled-up arm in warm water with a cup of white vinegar for 15 to 30 minutes, then clear the holes again and scrub it with a soft brush.
- 4
Check the hub
Look in the hub the arm sits on. Pick out seeds or glass so the arm can turn freely.
- 5
Refit or replace
Push each arm back on its hub until it clicks, or refit its nut. Spin it by hand to check it turns freely.
If an arm is cracked or warped, fit a new one matched to your model.
Buy the part
Spray arms
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The arm listed for your dishwasher's model number. Upper and lower arms are different parts.
- Any hub nut or bearing ring that goes with it.
- 6
Racks in and run it
Slide the racks back in. Make sure nothing tall hangs down into an arm's path. Switch on and run a cycle.
Buy the part
Get the right replacement
Buy the part
Spray arms
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The arm listed for your dishwasher's model number. Upper and lower arms are different parts.
- Any hub nut or bearing ring that goes with it.
Know your limits
When to call a pro
Stop and call a pro if
- The arms are clean and free but barely turn during a wash. The wash pump may be weak.
- The tube that feeds the upper arm is cracked or disconnected inside the tub.
FAQ
Spray arms questions
Why do my spray arm holes keep clogging?
Food that gets past a dirty or cracked filter ends up in the arms. Clean the filter at the same time.
How do I know if the arms are spinning?
Note where each arm points before a cycle. If it sits in exactly the same spot after the cycle, it may not be turning. Opening the door mid-cycle stops the arms, so you cannot watch them run.
Should I clean the spray arms regularly?
Several dishwasher manuals say to check the nozzles from time to time. Do it whenever you clean the filter or see dirty spots.
Related
Keep going
- SymptomDishwasher not cleaning dishesDishes come out gritty, filmy or with food still on them. A clogged filter or spray arms cause most of it. Low water, cool water, or a weak wash pump are next.Open guide
- Dishwasher partDishwasher filterMost dishwashers have a filter in the tub floor that catches food before the water goes around again. A clogged one leaves dishes dirty and the tub smelling. Twist it out, rinse it, twist it back.Open guide
- Dishwasher partCirculation pump and motorThe circulation pump pushes water through the spray arms. When its motor or bearings fail, the dishwasher fills but does not wash. It usually means pulling the dishwasher out to replace it.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
