WhatsBusted
3D model of a circulation pump and motor
Also called dishwasher wash motor, circulation pump

Dishwasher circulation pump replacement

Fills with water but no wash sound, or a loud hum or grind? Clean the filter and the arms first. If the pump really has failed, this is a bigger but doable job.

Difficulty
Hard
Time
1 hr–2.5 hr
Typical part cost
$80–$200Pro: $150–$600

Pull the dishwasher out of its cabinet, lay it down or tilt it, and swap the pump. Not hard work, but a lot of steps.

What it does

What the wash pump does

The circulation pump, sometimes called the wash motor, sits in the base under the sump. It pulls water from the tub floor and pushes it up through the spray arms.

On some dishwashers one motor both washes and drains. On others the drain pump is a separate part.

Why it fails

The motor bearings wear, giving a loud hum or drone, then the motor seizes. On most models that means replacing the pump and motor as one assembly.

A leaking shaft seal lets water into the motor.

Debris past the filter jams or breaks the impeller.

Symptoms

Signs of a bad wash pump

  • Fills, no wash noise

    You hear water come in, but then no spraying sound, and the dishes are barely wet.

    Full diagnosis
  • Loud hum or grind

    A hum, buzz or grind during the wash part of the cycle.

  • Spray arms not turning

    The arms are clean and free but sit in the same place after a cycle.

How to test it

Test the wash pump before you buy

Rule out the easy thingsNo meter needed
  1. Clean the filter and the spray arms.
  2. Check the tub gets water: look for water on the floor of the tub a minute or two into the cycle.
  3. Listen during the wash. A steady whir is normal. Silence, a hum or a grind is not.
Good
If the wash sound is back and dishes come clean, the filter was the problem.
Bad
Water in the tub, clean filter and arms, and still no wash or a loud hum. The pump is the likely cause.

Safety first

Before you touch anything

  1. 1

    Breaker off

    Switch off the dishwasher's breaker. If it is hardwired, check the wires in its connection box with a voltage tester before you touch them.

  2. 2

    Water off

    Close the hot water shutoff under the sink before you disconnect the supply line.

  3. 3

    Empty the sump

    Sponge out the tub floor. Water will still run out of the pump and hoses.

Tools you'll need

Grab these first

Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works

See the full repair tool kit

Step by step

How to replace the wash pump

  1. 1

    Power and water off

    Switch off the breaker and close the hot water shutoff. Sponge out the tub floor.

  2. 2

    Disconnect and pull it out

    Remove the kick plate. Disconnect the supply line from the inlet valve, and the power wires from the connection box or the plug.

    Take the drain hose off the disposal or sink drain. Open the door, remove the screws in the brackets at the top of the tub, and slide the dishwasher out slowly, feeding the hose through.

  3. 3

    Get at the pump

    Tilt the dishwasher onto its back on a towel, or lay it down, so you can reach the base.

    Photograph the pump's wires and hoses, then unplug the wires and release the hose clamps.

  4. 4

    Remove the old pump

    Remove its bracket screws or turn it to release it from the sump, and lift it away. Some come out with the sump attached.

  5. 5

    Fit the new pump

    Seat the new pump with its seal or O-ring aligned, refit the bracket, reconnect the hoses and clamps, and plug in the wires as in your photo.

  6. Buy the part

    Circulation pump and motor

    Opens Amazon in a new tab. Where’s my model number?

    What to look for

    • The pump listed for your dishwasher's model number.
    • Whether it includes the sump, the seals and the impeller.
  7. 6

    Reinstall and test

    Stand it up, slide it back in while feeding the drain hose through, and refit the brackets. Reconnect the drain hose, the supply line and the power.

    Open the water, switch on and run a cycle. Check for leaks under the dishwasher and at the supply line before you refit the kick plate.

Buy the part

Get the right replacement

Buy the part

Circulation pump and motor

Opens Amazon in a new tab. Where’s my model number?

What to look for

  • The pump listed for your dishwasher's model number.
  • Whether it includes the sump, the seals and the impeller.

Know your limits

When to call a pro

Stop and call a pro if

  • The dishwasher is hardwired and you are not comfortable disconnecting the wiring.
  • The pump hums but a new one does not fix it. The control board or the wiring may be at fault.
  • Your dishwasher is older and the pump costs close to half the price of a new dishwasher.

FAQ

Circulation pump and motor questions

How do I know it is the circulation pump?

It fills with water, the filter and arms are clean, and you hear no wash sound, or a loud hum or grind. That combination points to the pump.

Is a new pump worth it?

On a newer dishwasher, often. On an older one, compare the cost with a new dishwasher. The repair or replace calculator can help.

Can I replace just the motor bearings?

Usually not. Most pumps and motors are sold as one assembly, so worn bearings mean a new assembly. A few models sell motor parts separately. Check the parts diagram for yours.

Related

Keep going

Get the next fix before it breaks

A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.

We send it with Kit. Privacy