Dishwasher drain pump: test and replace
Clean the filter and check the hose first. If water still sits in the tub and the pump is silent or just hums, the pump is next. On some models it comes out from the front. On others the dishwasher has to come out.
- Difficulty
- Moderate
- Time
- 30 min–1.5 hr
- Typical part cost
- $50–$150Pro: $125–$400
- Tools
- 5See the list
On some models: kick plate off, then a plug, a clamp and a bracket. On many others the dishwasher has to be pulled out and laid on its back to reach the pump.
What it does
What the drain pump does
The drain pump is a small motor and impeller in the base of the dishwasher, beside or attached to the sump. At the end of each wash and rinse it pushes the water up the drain hose.
Some dishwashers use one motor that both washes and drains. Others have a separate, smaller drain pump. This guide is for the separate kind.
Why it fails
Glass, bones, seeds or a label get past the filter and jam the impeller.
The motor winding burns out, and the pump goes silent.
Symptoms
Signs of a bad drain pump
Water left after every cycle
The filter is clean and the hose is clear, but water still sits in the tub.
Full diagnosisHum but no drain
You hear a hum at the end of the cycle but no water leaves. Something is jamming the impeller.
Full diagnosisSilent at drain time
No pump sound at all when it should drain.
How to test it
Test the drain pump before you buy
- Switch off at the breaker. Bail or sponge out the standing water.
- Take out the filter and look into the sump below it for glass, bones or seeds.
- Pick out anything you find with pliers. Do not use your fingers on broken glass.
- Good
- Something was jamming it. Refit the filter and run a rinse. If it drains, you are done.
- Bad
- Nothing there and it still will not drain. Check the hose, then test the pump.
- Switch off at the breaker and reach the pump (steps 1 and 2 below).
- Unplug the wires from the drain pump. Touch one probe to each of its two terminals.
A good drain pump typically reads
Often about 5–60 Ω. Some pumps read much higher, about 160–260 Ω
Typical range. Check your part label or manual for the exact spec. Readings vary a lot by maker and design. Check the value for your exact part, often on its label or in the tech sheet, before you decide it is bad.
- Good
- A steady reading that is not OL and not near 0 Ω usually means the motor winding is intact. Look for a jam or a blocked hose.
- Bad
- OL (open) or near 0 Ω means the motor has failed. Replace the pump.
Safety first
Before you touch anything
- 1
Breaker off
Switch off the dishwasher's breaker, or unplug it under the sink. Hardwired dishwashers have no plug, so use the breaker and check with a voltage tester that the power is off before you touch any wires.
- 2
Water off
Close the hot water shutoff under the sink.
- 3
Remove standing water
Bail and sponge out the tub before you open the pump. Water will still come out of the pump and hose.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Non-contact voltage testerPen styleOn a hardwired dishwasher, confirms the power is really off before you touch any wires.Typically $15–$30Shop this tool
- Multi-bit screwdriverPhillips, flat, squareRemoves the kick plate screws.Typically $10–$25Shop this tool
- Nut driver1/4 in. hexOptionalMany kick plates and pump brackets use 1/4 in. hex screws.Typically $6–$15Shop this tool
- Torx driver bitsT15, T20, T25OptionalSome dishwashers use Torx screws.Typically $6–$15Shop this tool
- Hose clamp pliersReleases the clamp on the drain hose at the pump.Typically $10–$25Shop this tool
- Shallow pan and towelsCatches the water still in the pump and hose.Typically $5–$15Shop this tool
- Digital multimeterΩ, V, µF, µATests the pump motor before you buy one.Typically $25–$60Shop this tool
Step by step
How to replace the drain pump
- 1
Power and water off
Switch off the breaker, close the shutoff under the sink, and sponge out any standing water.
- 2
Remove the kick plate
Take out the screws along the bottom of the door frame and pull off the kick plate and any panel behind it.
If you cannot reach the pump from the front, pull the dishwasher out as in the circulation pump guide and lay it on its back on a towel.
- 3
Unplug and unclamp
Photograph the wires, then pull them off the pump.
Set the pan underneath. Release the clamp on the drain hose at the pump and pull the hose off.
- 4
Remove the pump
Take out any screw or bracket that holds the pump, then twist or pull it out of the sump.
Many pumps turn a quarter turn counterclockwise to release. Others use screws. Check a parts diagram for yours.
- 5
Fit the new pump
Check the seal on the new pump is seated. Push or twist it into the sump the same way the old one came out, and refit the bracket.
Push the hose on, refit the clamp and reconnect the wires as in your photo.
Buy the part
Drain pump
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The pump listed for your dishwasher's model number.
- The same mounting, seal and connector. Some come with a new seal or a new impeller.
- 6
Test before you close up
Open the water, switch the power on, and run a short rinse. Watch under the pump for drips.
When it drains cleanly and stays dry, switch off and refit the kick plate.
Buy the part
Get the right replacement
Buy the part
Drain pump
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The pump listed for your dishwasher's model number.
- The same mounting, seal and connector. Some come with a new seal or a new impeller.
Know your limits
When to call a pro
Stop and call a pro if
- Your dishwasher uses one motor to wash and drain, and that motor has failed. It is a bigger job.
- The pump is new, the hose is clear and it still will not drain. The control board may not be powering it.
- Water leaks from the base and you cannot find the source.
FAQ
Drain pump questions
How do I know if the drain pump is bad?
Rule out the cheap things first: clean the filter and check the drain hose. If it is still silent or only hums at drain time, test the pump.
Can I clear a jammed pump without replacing it?
Often, yes. Most jams are glass, bones or seeds in the sump. Pick them out and test again before you buy a pump.
Is it normal to hear the pump hum?
A hum with water draining is normal. A hum with no water moving means a jam.
Related
Keep going
- SymptomDishwasher won't drainWater sits in the tub after a cycle. A packed filter, a clogged disposal or drain hose, or a disposal knockout plug causes most of it. A jammed or failed drain pump is next.Open guide
- Dishwasher partDishwasher filterMost dishwashers have a filter in the tub floor that catches food before the water goes around again. A clogged one leaves dishes dirty and the tub smelling. Twist it out, rinse it, twist it back.Open guide
- Dishwasher partDrain hose, high loop and air gapThe drain hose carries water from the drain pump to the disposal or sink drain, over a high loop or through an air gap. A kink, a clog, a missing loop or a disposal knockout plug stops it. Check and clear it.Open guide
- Dishwasher partCirculation pump and motorThe circulation pump pushes water through the spray arms. When its motor or bearings fail, the dishwasher fills but does not wash. It usually means pulling the dishwasher out to replace it.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
