Garbage disposal splash guard replacement
A torn or slimy splash guard lets food fly up, makes the sink smell, and can leak at the top. A new one is cheap.
- Difficulty
- Easy
- Time
- 10–45 min
- Typical part cost
- $10–$15Pro: $100–$250
- Tools
- 3See the list
On some units it pulls out from above. On others, the disposal has to come down to reach it.
What it does
What the splash guard does
The splash guard is the rubber flap you see when you look down the sink drain. It lets food in and keeps it from spraying back up while the disposal runs.
On many disposals it is molded into the main gasket that seals the top of the unit to the sink flange.
Why it fails
The rubber flaps tear, stretch or stiffen with age.
Food and grease build up under the flaps and smell.
A damaged guard can let water leak between the disposal and the flange.
Symptoms
Signs of a bad splash guard
Torn or missing flaps
Look down the drain with a light. Gaps or ragged rubber mean it is worn.
Sink smells
A sour smell from the drain that cleaning the sink does not fix.
Leaks at the top
Water between the disposal and the sink flange can come from a damaged guard.
Full diagnosis
How to test it
Test the splash guard before you buy
- Switch off and unplug the disposal.
- Shine a light down the drain and lift each flap with a spoon handle. Look for tears and buildup underneath.
- Scrub under the flaps with an old toothbrush and dish soap.
- Good
- Whole flaps that spring back. Cleaning may have fixed the smell.
- Bad
- Torn, stretched or stiff flaps. Replace the guard.
Safety first
Before you touch anything
- 1
Switch off and unplug
Turn off the wall switch and unplug the disposal, or switch off its breaker. Never reach past the guard.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Multi-bit screwdriverPhillips, flat, squareHelps lift the old guard and works the mount ring.Typically $10–$25Shop this tool
- Tongue-and-groove pliers10 in.Loosens the trap if the disposal has to come down.Typically $12–$28Shop this tool
- Nitrile glovesOld guards are slimy.Typically $8–$15Shop this tool
Step by step
How to replace the splash guard
- 1
Power off
Turn off the wall switch and unplug the disposal, or switch off its breaker.
- 2
Try lifting it out from above
On some disposals the guard is a separate piece that pulls straight up out of the flange. With the power off, grip its top edge from the sink and pull. Do not reach down past it.
If it will not budge, it may be part of the mounting gasket, and the disposal has to come down. Your manual will say which kind you have.
- 3
If needed, take the disposal down
Put a bucket under it. Loosen the trap and take off the dishwasher hose. Support the disposal and twist its lower ring to unhook it from the mount.
Peel the old guard off the top of the disposal. Wipe the opening clean.
- 4
Fit the new guard
Stretch the new guard over the top rim of the disposal, or press it into the flange, until it sits flush all the way around and the flaps move freely.
Buy the part
Splash guard
Opens Amazon in a new tab. Where’s my model number?
What to look for
- A guard made for your disposal's brand and mount. Sizes and rims differ.
- 5
Rehang and test
Lift the disposal, hook it onto the mount and twist until it locks. Reconnect the trap and the dishwasher hose.
Power on, run water and the disposal, and check for drips at the top.
Buy the part
Get the right replacement
Buy the part
Splash guard
Opens Amazon in a new tab. Where’s my model number?
What to look for
- A guard made for your disposal's brand and mount. Sizes and rims differ.
Know your limits
When to call a pro
Stop and call a pro if
- The leak at the top continues with a new guard and a tight flange.
- You cannot safely support the disposal while it comes down.
FAQ
Splash guard questions
How do I clean a smelly splash guard?
Power off, then scrub under each flap with an old toothbrush and dish soap. Run cold water afterward.
Does the splash guard stop leaks?
On many disposals, yes, because it doubles as the top gasket. A torn one can leak at the flange.
Do I need to take the disposal down to change it?
It depends on the model. Some pull straight up from the sink, others need the unit down. Check your manual, or try pulling it straight up first with the power off.
Related
Keep going
- SymptomGarbage disposal leakingWater under the sink, traced to the disposal. Top leaks are the sink flange. Side leaks are the discharge elbow or the dishwasher hose. Bottom leaks mean the unit has failed inside.Open guide
- SymptomGarbage disposal making loud noisesRattles, clanks or harsh grinding from the disposal. A spoon, a bottle cap or a knockout plug in the chamber is the usual cause. Loose mounting or worn parts come next.Open guide
- Garbage disposal partSink flange and mounting ringThe sink flange is the metal drain ring in the sink. Plumber's putty seals it, and the mounting ring underneath clamps it and holds the disposal. When the putty dries out or the bolts loosen, it leaks from the top.Open guide
- Garbage disposal partWhole disposal unitWhen the body cracks, it leaks from the bottom or the reset button, or the motor is dead, the disposal gets replaced as a unit. Unhook it, move the cord, hang the new one and reconnect the drains.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
