Electric range infinite switch test and replacement
Electric coil ranges only. A burner that stays cold with a good coil, or stays red hot on low, points to the switch behind its knob.
- Difficulty
- Moderate
- Time
- 30 min–1 hr
- Typical part cost
- $20–$120Pro: $100–$190
- Tools
- 5See the list
Pull the range out, open the control panel from the back and move four or five wires one at a time. Easy, but fiddly and 240 V.
What it does
What the infinite switch does
Behind each knob is an infinite switch. It does not dim the element; it switches it fully on and off in a repeating cycle. On high it stays on; on low it is on only a small part of the time.
Power comes in on two line terminals and goes out to the element on two others, usually marked L1, L2, H1 and H2.
Why it fails
The contacts inside wear, pit and stick. A switch stuck open leaves the element cold; one stuck closed keeps it red hot on every setting.
Loose or overheated wire connections at the back of the switch burn the terminals.
Symptoms
Signs of a bad infinite switch
Cold burner, good coil
The coil heats fine in another spot, and its receptacle is clean, but it will not heat in its own spot.
Full diagnosisRed hot on every setting
The element glows full on even on low, or will not turn off.
Full diagnosisBurned terminals behind the knob
With the control panel open, the switch's terminals or wires look scorched or melted.
How to test it
Test the infinite switch before you buy
- Unplug the range. Open the control panel from the back (steps below) and photograph the switch's wires.
- Pull the wires off the switch.
- Turn the knob to high; you should hear it click. Probe L1 to H1, then L2 to H2.
A good switch on high typically shows
Continuity across L1 to H1 and L2 to H2
Typical range. Check your part label or manual for the exact spec. A switch can pass this test and still fail under load. If everything else checks out, a technician can test it with power on.
- Good
- Continuity on both pairs on high, and open when turned off. The switch is probably fine; check the wiring between it and the receptacle.
- Bad
- Open on high, or closed when off. Replace the switch.
Safety first
Before you touch anything
- 1
Unplug it or switch off the breaker
The switches carry the full 240 V to the elements. Unplug the range, or turn off its breaker, and check with a voltage tester before you touch any wire.
- 2
Cooktop cool
Let the cooktop cool before you move the range.
Wait about 15 min
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexRemoves the control panel's back cover on many ranges.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareRemoves the switch's mounting screws behind the knob.Typically $10–$25Shop this tool
- Needle-nose pliersPulls the push-on wire connectors off the switch.Typically $8–$20Shop this tool
- Digital multimeterΩ, V, µF, µAChecks the switch contacts for continuity.Typically $25–$60Shop this tool
- Non-contact voltage testerPen styleConfirms the panel is dead before you touch the wiring.Typically $15–$30Shop this tool
Step by step
How to replace the infinite switch
- 1
Power off and pull the range out
Unplug the range or turn off its breaker. Slide it forward onto cardboard to protect the floor.
- 2
Open the control panel
Remove the screws on the back of the control panel and lift or tilt off its rear cover. The switches sit behind the knobs.
- 3
Photograph and label the wires
Take a clear photo of the switch's wires. Label each with tape matching its terminal: L1, L2, H1, H2, and any pilot light terminal.
- 4
Remove the old switch
Pull the knob off the front. Remove the two screws that hold the switch to the panel, usually under where the knob was.
Pull the wires off the old switch.
- 5
Wire the new switch
Move each wire to the same terminal on the new switch, one at a time, checking the labels. Push each connector on firmly.
Mount the switch and refit the knob.
Buy the part
Infinite switch
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your range's model number. Switches differ by element size and terminal layout.
- The part number printed on the old switch.
- For a dual element, a dual switch that matches it.
- 6
Close up and test
Refit the panel cover, restore power and push the range back so the anti-tip bracket engages.
Test the burner on high, then on low: on low it should click on and off.
Buy the part
Get the right replacement
Buy the part
Infinite switch
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your range's model number. Switches differ by element size and terminal layout.
- The part number printed on the old switch.
- For a dual element, a dual switch that matches it.
Know your limits
When to call a pro
Stop and call a pro if
- Wires or terminals behind the panel are burned or melted.
- The switch tests good and the element is good, but the burner still does not heat.
- Your range uses electronic touch controls instead of knobs.
FAQ
Infinite switch questions
Is it the switch or the receptacle?
Look at the receptacle first: it is quicker and scorching is easy to see. If the receptacle is clean and a good coil still will not heat in that spot, it is likely the switch.
Why does my burner click on and off?
That is how an infinite switch works below high. It cycles the element on and off.
Can I swap switches between burners to test?
Only if they are the same part number, and only with the power off. It is usually quicker to test the suspect switch with a meter.
Related
Keep going
- SymptomElectric stove burner not heatingOne coil element on an electric range stays cold, or stays red hot on every setting. The coil itself is the most likely cause, then a burned receptacle, then the infinite switch behind the knob.Open guide
- Range partCoil surface elementElectric coil ranges only. Each coil element plugs into a receptacle under its drip bowl. A dead coil, a burned receptacle or a failed switch all leave one burner cold. The coil itself just unplugs.Open guide
- Range partOven control boardThe control board is the electronic control behind the keypad and display. It reads the temperature sensor and switches the bake and broil elements or the gas igniters. When it fails, the display goes dead or garbled, keys stop responding, or the oven will not heat even with good parts.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
