Range oven control board replacement
The control board is the last suspect, not the first. Test the elements, the igniter and the sensor before you spend money here.
- Difficulty
- Moderate
- Time
- 30 min–1 hr
- Typical part cost
- $90–$400Pro: $150–$600
- Tools
- 4See the list
Not hard, but many wires. A clear photo of every connector, and matching wires to terminal labels, is what makes it go right.
What it does
What the control board does
Behind the keypad and display, the control board runs the clock, the timers and the oven. On an electric range it sends power to the bake and broil elements; on a gas range, to the igniters and through them to the safety valve.
It reads the oven temperature sensor and switches the heat on and off to hold your setting.
Why it fails
Relays on the board that switch the heating elements can wear out, so a good element never gets power. The display or keypad can also fail.
Heat, power surges and spills on the keypad shorten its life.
Symptoms
Signs of a bad control board
Dead or garbled display
The clock and display are blank or show nonsense, with the range plugged in and the breaker on.
Full diagnosisGood parts, no heat
The elements or igniter and the sensor all test good, but the oven never heats.
Full diagnosisKeys do nothing
Some or all of the touch pads stop responding.
Error code that will not clear
An error code comes back after a power reset, and the part it points to tests good.
Full diagnosis
How to test it
Test the control board before you buy
- Check the breaker. An electric range needs both halves of its double breaker on.
- Turn the breaker off for a minute and back on to reset the control.
- Test the bake element or the oven igniter, and the temperature sensor.
- Good
- Everything tests good and the board still does not heat or respond. Replace the board.
- Bad
- One of the other parts failed. Fix that first; the board is probably fine.
Safety first
Before you touch anything
- 1
Unplug it or switch off the breaker
Unplug the range or turn off its breaker. On an electric range the control panel carries 240 V. Check with a voltage tester before you touch any wire.
- 2
Gas off on a gas range
On a gas range, close the gas shutoff before you pull the range out.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexMost control panel back covers use 1/4 in. hex screws.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareRemoves the board's mounting screws and any front trim screws.Typically $10–$25Shop this tool
- Needle-nose pliersHelps release tight connectors.Typically $8–$20Shop this tool
- Non-contact voltage testerPen styleConfirms the panel is dead before you touch any wire.Typically $15–$30Shop this tool
Step by step
How to replace the control board
- 1
Power off, gas off, pull it out
Unplug the range or turn off its breaker. On a gas range, close the gas shutoff. Slide the range forward onto cardboard to protect the floor.
- 2
Open the control panel
Remove the screws holding the control panel's back cover, or the console's trim, and take it off to expose the board.
- 3
Photograph every connector
Take clear photos of every wire and connector on the board. Note the wire colors against the terminal labels printed on the board.
Tip. Replacement boards sometimes put the connectors in different places. Match by the printed labels, not just by position.
- 4
Disconnect and remove the board
Unplug the connectors, pressing any locking tabs. Remove the board's mounting screws and lift it out.
- 5
Fit the new board
Transfer the overlay or any brackets if your new board needs them. Mount the board, then plug in each connector to match your photos and the terminal labels.
Buy the part
Oven control board
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your range's exact model number. Boards are model specific, and the wrong one can look identical.
- The part number on the old board's label.
- Whether the keypad overlay comes with it or has to be moved over.
- 6
Close up and test
Refit the panel cover. Open the gas, restore power and push the range back so the anti-tip bracket engages.
Set the clock, then test bake and broil.
Buy the part
Get the right replacement
Buy the part
Oven control board
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your range's exact model number. Boards are model specific, and the wrong one can look identical.
- The part number on the old board's label.
- Whether the keypad overlay comes with it or has to be moved over.
Know your limits
When to call a pro
Stop and call a pro if
- Wires or connectors on the board are burned or melted.
- The new board does not fix it. The wiring or a relay board needs testing with power on.
- Your range has a separate relay board and you are not sure which one failed.
FAQ
Oven control board questions
How do I reset my oven's control?
Turn off the range's breaker, or unplug it, for a minute or so, then turn it back on. That clears many temporary faults.
Is it the board or the sensor?
Test the temperature sensor first. If it reads about 1,080 Ω at room temperature, the sensor is fine and the board becomes the suspect.
Is a new control board worth it on an older range?
It depends. A board can cost a good share of a basic new range. On an older, inexpensive range, compare the cost against replacing it with the repair or replace calculator.
Related
Keep going
- SymptomOven not heatingThe oven will not heat, or barely warms. On an electric range the bake element is the usual cause, after the breaker. On a gas range a weak igniter is the most likely, after the gas supply. The sensor and the control come later.Open guide
- SymptomOven temperature wrongFood burns, stays raw or browns unevenly. Measure the real temperature first. A small, steady offset is often fixed in the settings. A big swing usually means a temperature sensor, an element or igniter that is failing, or a door that does not seal.Open guide
- Range partOven temperature sensorThe temperature sensor is the thin probe on the oven's back wall. It tells the control how hot the oven is. When it drifts or fails, the oven runs too hot or too cool, or the control shows an error and stops heating.Open guide
- Range partBake elementElectric ranges only. The bake element is the heating loop along the bottom of the oven. When it burns out, the oven heats slowly, unevenly or not at all on bake. It is usually two screws and two wires.Open guide
- Range partGas oven igniterGas ranges only. The oven igniter glows to light the bake burner and, at the same time, opens the oven safety valve. A weak igniter still glows but cannot draw enough current to open the valve, so the oven heats slowly or not at all.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
