Gas oven igniter test and replacement
Gas ranges only. If the igniter glows but the oven never lights, or takes ages to, the igniter has probably gone weak. You can swap it without opening any gas fitting.
- Difficulty
- Easy
- Time
- 30 min–1 hr
- Typical part cost
- $15–$40Pro: $150–$250
- Tools
- 3See the list
Remove the oven bottom and a burner cover, two screws and a plug or two wire nuts. The care points are not touching the element and stopping if you would have to remove the burner.
What it does
What the oven igniter does
When you set the oven to bake, power flows through the igniter and the oven safety valve, which are wired in series. The igniter heats up and glows bright orange.
As it heats, it draws more current. Once it draws enough, the safety valve opens and gas flows into the bake burner, where the glowing igniter lights it. If the igniter is broken, no current flows; if it is weak, too little flows. Either way the valve stays shut. That is the safety.
Why it fails
Igniters weaken with age. A weak one still glows, but never draws enough current to open the valve, or only does after a long wait.
The element is fragile. Touching it or bumping it during cleaning can crack it, and a cracked igniter does not glow at all.
Symptoms
Signs of a bad oven igniter
Glows, but no flame
Look through the slots in the oven floor. The igniter glows orange but the burner never lights, and the oven stays cold.
Full diagnosisTakes forever to preheat
The burner lights after a long glow, the oven takes much longer than it used to, or it never reaches the set temperature.
Full diagnosisLights late with a whoomp
The burner lights with a loud whoomp after a long wait. Stop using the oven and replace the igniter.
Full diagnosisNo glow at all
The igniter stays dark when the oven calls for heat. It is cracked or open, or not getting power.
Full diagnosis
How to test it
Test the oven igniter before you buy
- Take out the racks, set the oven to bake and watch the igniter through the slots in the oven floor. On some ovens you may need a flashlight.
- Time how long it glows before the burner lights.
A technician can confirm a weak igniter with a clamp ammeter: a healthy one draws around 3 amps or more, a weak one less.
- Good
- It glows bright and the burner lights smoothly within about a minute. The igniter is fine.
- Bad
- It glows for well over a minute with no flame, lights with a whoomp, or never lights. Replace the igniter.
- Unplug the range and shut off the gas. Reach the igniter (steps below) and disconnect its two wires.
- Probe the two igniter wires.
A good igniter shows
Continuity: a steady reading, not OL
Typical range. Check your part label or manual for the exact spec.
- Good
- A reading means the element is not broken. It can still be weak, so if it glows without lighting, replace it anyway.
- Bad
- OL means it is cracked or open. Replace it.
Safety first
Before you touch anything
- 1
Unplug the range
Pull the plug, or turn off its breaker. The igniter runs on household voltage.
- 2
Close the gas shutoff
Turn the gas valve behind or near the range so the handle sits crosswise to the pipe. You will not open any gas fitting in this job; this is a second layer of safety.
- 3
Let the oven cool
The burner area stays hot for a while after use.
Wait about 30 min
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexThe oven bottom, burner cover and igniter screws are usually 1/4 in. hex.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareSome oven bottoms use Phillips screws.Typically $10–$25Shop this tool
- Wire stripperOptionalNeeded if you splice the new igniter in with ceramic wire nuts.Typically $10–$25Shop this tool
- HeadlampThe igniter sits low at the back of the burner area.Typically $12–$30Shop this tool
- Nitrile glovesOptionalLets you handle the new igniter by its mounting bracket without touching the element.Typically $8–$15Shop this tool
Step by step
How to replace the oven igniter
- 1
Power off and gas off
Unplug the range or turn off its breaker. Close the gas shutoff valve. On many ranges you can reach both through the storage drawer opening.
- 2
Remove the oven bottom
Take out the racks and, if it helps, lift off the oven door. The oven bottom panel is usually held by two screws at the back. Remove them, lift the back of the panel and slide it out.
- 3
Remove the burner cover
A metal cover or heat deflector sits over the bake burner. Remove its screws or nut and lift it off. The igniter is beside the burner.
- 4
Check that you can reach it
The igniter should be held to a bracket by two screws or nuts, reachable without moving the burner.
Careful. If you would have to remove the burner, or loosen any gas tube or fitting, to reach the igniter, stop here and call a pro.
- 5
Disconnect the wires
Follow the igniter's two wires. Some end in a plug, reached behind a small cover in the oven corner or from the storage drawer opening. Others are joined with ceramic wire nuts. Unplug the plug, or untwist the wire nuts.
Photograph the routing first. The new wires should follow the same path, clear of the burner.
- 6
Remove the old igniter
Remove the two mounting screws or nuts and lift the igniter out.
- 7
Fit the new igniter
Mount it in the same position on the same bracket. Handle it only by its ceramic base or bracket.
Connect it with its plug. If the plug does not match, cut both plugs off, strip about 1/2 in. of each wire and join them with the ceramic wire nuts that come with the igniter. Plastic wire nuts melt here.
Careful. Do not touch the igniter's element. It is brittle.
Buy the part
Gas oven igniter
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your range's model number. Igniters come flat or round, and the bracket, plug and wire length differ.
- The part number on the old igniter's ceramic base, if you can read it.
- Whether it is the bake or the broil igniter. Some gas ranges have both.
Universal oven igniters with ceramic wire nuts fit many ranges. Match the shape and current rating to your model's part.
- 8
Reassemble and test
Refit the burner cover, the oven bottom, the door and the racks. Open the gas valve, restore power, and push the range back so the anti-tip bracket engages.
Set bake and watch: the igniter should glow and the burner light smoothly within about a minute.
Buy the part
Get the right replacement
Buy the part
Gas oven igniter
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your range's model number. Igniters come flat or round, and the bracket, plug and wire length differ.
- The part number on the old igniter's ceramic base, if you can read it.
- Whether it is the bake or the broil igniter. Some gas ranges have both.
Universal oven igniters with ceramic wire nuts fit many ranges. Match the shape and current rating to your model's part.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas at any point. Leave the house and call your gas supplier from outside.
- Reaching the igniter means removing the burner or loosening any gas tube or fitting.
- A new igniter glows bright but the burner still never lights. The oven safety valve or the gas supply is the next suspect.
- The burner lights with flames rolling out, or the flame is yellow and lazy.
FAQ
Gas oven igniter questions
The igniter glows. How can it be bad?
Because glowing is not enough. The safety valve only opens once the igniter draws its full current. A weak igniter can glow orange all day without reaching that, so the burner never lights.
Do I need to turn off the gas?
The safety valve should not let gas flow without a working igniter, but closing the shutoff is cheap insurance. You will not open any gas fitting in this job.
Is it the igniter or the oven safety valve?
Usually the igniter. It is much more often the igniter than the valve. If a new igniter glows and the burner still never lights, call a pro to check the oven safety valve.
My gas oven has a broil igniter too. Is it the same?
It works the same way. Check your manual for how to reach it, and make sure you buy the one listed for the broil position.
Related
Keep going
- SymptomOven not heatingThe oven will not heat, or barely warms. On an electric range the bake element is the usual cause, after the breaker. On a gas range a weak igniter is the most likely, after the gas supply. The sensor and the control come later.Open guide
- SymptomOven temperature wrongFood burns, stays raw or browns unevenly. Measure the real temperature first. A small, steady offset is often fixed in the settings. A big swing usually means a temperature sensor, an element or igniter that is failing, or a door that does not seal.Open guide
- Range partOven safety valveGas ranges only. The oven safety valve opens only when the igniter is hot and drawing enough current, then lets gas into the bake burner. A weak igniter causes the same symptoms, so it is checked first. Replacing the valve means opening gas fittings, which is licensed work.Open guide
- Range partOven temperature sensorThe temperature sensor is the thin probe on the oven's back wall. It tells the control how hot the oven is. When it drifts or fails, the oven runs too hot or too cool, or the control shows an error and stops heating.Open guide
- Range partOven control boardThe control board is the electronic control behind the keypad and display. It reads the temperature sensor and switches the bake and broil elements or the gas igniters. When it fails, the display goes dead or garbled, keys stop responding, or the oven will not heat even with good parts.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
