Electric range coil element test and replacement
Electric coil ranges only. One burner stays cold? Swap it with a good one from another spot. That single test tells you whether it is the element or what is behind it.
- Difficulty
- Anyone can do it
- Time
- 5–30 min
- Typical part cost
- $40–$80Pro: $110–$240
- Tools
- 2See the list
The coil lifts and unplugs. A receptacle is one screw and two wires under the cooktop.
What it does
What the surface element does
Each coil is a sealed heating element with two prongs that plug into a receptacle under the cooktop. The knob's switch sends it 240 V, cycling on and off to give you low through high.
Many coils made since 2019 have a small limiter built in, which cycles the power to keep the pan from getting hot enough to start a fire. They still test the same way.
Why it fails
The coil can burn open. Look for a blister, a split or a section that never glows.
The receptacle it plugs into wears too. Loose or corroded prongs make heat, and you see scorched, pitted or melted terminals.
Symptoms
Signs of a bad surface element
One burner stays cold
The other burners heat but this one stays dark on every setting.
Full diagnosisBlister, split or dark section
Part of the coil never glows, or you see a bubble or crack in it.
Scorched prongs or sparking
The prongs are pitted or burned, or you see sparking or it cuts in and out on high. Turn it off. Suspect the receptacle as well as the coil.
Full diagnosis
How to test it
Test the surface element before you buy
- With the cooktop cool and the switches off, lift the cold coil and unplug it. Do the same with a working coil of the same size.
- Plug the working coil into the dead spot and turn that knob on.
- Good
- The good coil heats in the dead spot. Your original coil is bad. Replace it.
- Bad
- The good coil stays cold in that spot too. The coil was fine; the problem is the receptacle, the switch or the wiring.
- Unplug the coil from the range.
- Touch one probe to each prong.
A good coil typically reads
About 20–40 Ω
Typical range. Check your part label or manual for the exact spec.
- Good
- A reading in that range means the coil is intact.
- Bad
- OL means it is open. Replace it.
Safety first
Before you touch anything
- 1
Power off for anything under the cooktop
Swapping a coil only needs the knob off and the cooktop cool. Before you touch a receptacle or anything under the cooktop, unplug the range or turn off its breaker.
- 2
Let the coils cool
A coil can stay hot enough to burn for a while after it goes dark.
Wait about 15 min
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Digital multimeterΩ, V, µF, µAA resistance reading settles whether the coil is open.Typically $25–$60Shop this tool
- Multi-bit screwdriverPhillips, flat, squareRemoves the receptacle's mounting screw if you need to replace it.Typically $10–$25Shop this tool
- Needle-nose pliersOptionalHelps with receptacle wire connectors.Typically $8–$20Shop this tool
Step by step
How to replace the surface element
- 1
Knobs off, power off
Turn every knob to off and let the cooktop cool.
If you might need to replace the receptacle, unplug the range or turn off its breaker now.
- 2
Unplug the coil
Lift the edge of the coil opposite the receptacle a few inches and pull it straight out of the receptacle. Lift out the drip bowl.
- 3
Look at the receptacle
Look into the receptacle and at the coil's prongs. Scorched, pitted or melted terminals mean the receptacle should be replaced along with the coil. A new coil in a burned receptacle soon fails again.
- 4
Replace the receptacle, if needed
With the range unplugged, remove the receptacle's mounting screw and pull it up. Move the wires from the old receptacle to the new one one at a time, or use the connectors that came with it, and screw it back in place.
- 5
Plug in the new coil
Set the drip bowl back. Push the new coil's prongs fully into the receptacle and lower the coil so it sits flat.
Buy the part
Coil surface element
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The same diameter and number of turns as the old coil.
- The same prong style as the old coil.
- If your range was made from 2019 on, a coil with the built-in limiter like the original.
Universal coils fit many ranges, as long as the size and prong style match. Your model number confirms it.
- 6
Power on and test
Restore power and turn the knob to high. The coil should glow evenly within a minute or two. Try a low setting to see it cycle.
Buy the part
Get the right replacement
Buy the part
Coil surface element
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The same diameter and number of turns as the old coil.
- The same prong style as the old coil.
- If your range was made from 2019 on, a coil with the built-in limiter like the original.
Universal coils fit many ranges, as long as the size and prong style match. Your model number confirms it.
Know your limits
When to call a pro
Stop and call a pro if
- The wires to the receptacle are burned, melted or hard to reach.
- A good coil and a new receptacle still do not heat. The switch or wiring needs testing with power on.
- The range trips its breaker when the burner is turned on.
FAQ
Coil surface element questions
The coil works in another spot but not in its own. Now what?
Then the coil is fine. Look at the receptacle for scorching first. If it looks good, the infinite switch behind that knob is next.
Why does my new coil turn itself off on high?
Coils with a built-in limiter cycle the power to keep the pan below a set temperature. Some short off periods are normal on those.
Does this apply to smooth glass cooktops?
No. Glass cooktops use radiant elements fastened under the glass, which is a different job. This guide is for plug-in coil elements.
Related
Keep going
- SymptomElectric stove burner not heatingOne coil element on an electric range stays cold, or stays red hot on every setting. The coil itself is the most likely cause, then a burned receptacle, then the infinite switch behind the knob.Open guide
- Range partInfinite switchElectric coil ranges only. The infinite switch behind each knob cycles power to one surface element to give you low through high. When its contacts stick or burn, the element stays off, stays on full, or will not hold a setting.Open guide
- Range partOven control boardThe control board is the electronic control behind the keypad and display. It reads the temperature sensor and switches the bake and broil elements or the gas igniters. When it fails, the display goes dead or garbled, keys stop responding, or the oven will not heat even with good parts.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
