WhatsBusted
3D model of an oven door hinges
Also called oven door hinge, oven hinge spring

Oven door hinge replacement

A door that drops open, will not close flat or lets heat pour out the top usually has a bent hinge or a broken spring. Replace them as a pair and the door shuts like new.

Difficulty
Easy
Time
15–45 min
Typical part cost
$80–$300Pro: $100–$350

Lift the door off, pull the drawer, unhook two springs and swap a few screws. The springs are strong, so keep your fingers clear.

What it does

What the door hinges does

Two hinges carry the oven door, one on each side. Each has a strong spring that pulls the door closed and controls how fast it opens.

On many ranges the springs are anchored low in the body, behind the storage drawer, so you reach them from the drawer opening.

Why it fails

Springs and the rollers or pins they work on wear and break with age.

Symptoms

Signs of a bad door hinges

  • Door drops open

    The door falls open on its own instead of easing down.

  • Will not close or stay closed

    The door does not close flat, springs back open, or sits higher on one side.

    Full diagnosis
  • Heat escaping around the door

    You feel heat at the top of the door, or the oven takes longer to heat because the door does not seal.

    Full diagnosis

How to test it

Test the door hinges before you buy

Look and feelNo meter needed
  1. With the oven cool, open and close the door slowly a few times. Watch both sides.
  2. Pull out the storage drawer and look at the springs on each side of the drawer opening, if your range has them there.
Good
Both sides move evenly and the door closes flat and stays shut. The hinges are fine; check the door gasket instead.
Bad
One side drops faster or sits crooked, a hinge arm is bent, or a spring is broken or unhooked. Replace both hinges.

Safety first

Before you touch anything

  1. 1

    Oven off and cool

    Unplug the range or turn off its breaker, and let the oven cool completely before you lift the door off.

  2. 2

    Mind the springs and the weight

    Oven doors are heavy and the hinge springs are strong. Wear gloves, keep fingers out of the hinge, and never lift the door by its handle.

Tools you'll need

Grab these first

Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works

See the full repair tool kit

Step by step

How to replace the door hinges

  1. 1

    Power off

    Unplug the range or turn off its breaker. Let the oven cool.

  2. 2

    Lift the door off

    Open the door fully. Flip the hinge locks or latches on each side toward the door. Close the door partway until it stops, grip it by the sides and lift it up and off. Never lift it by the handle.

    Lay it on a towel or blanket, handle side down.

  3. 3

    Unhook the springs

    Pull out the storage drawer. On many ranges each hinge's spring hooks to a tab low in the body. Note where each end attaches, then unhook it with pliers.

  4. 4

    Remove the old hinges

    Remove the screws that hold each hinge to the front frame and pull the hinges out through their slots.

  5. 5

    Fit the new hinges

    Replace both hinges, even if only one failed, so they match. Slide each new hinge into its slot, refit the screws and rehook the springs where the old ones attached.

  6. Buy the part

    Oven door hinges

    Opens Amazon in a new tab. Where’s my model number?

    What to look for

    • Your range's model number. Hinges are specific to the door and body.
    • A pair, or two of the same hinge. Some kits include new springs.
  7. 6

    Hang the door and test

    Slide the door's slots back onto the hinge arms, open it fully, and flip the hinge locks back to the locked position. Close it and check it sits flat and stays shut.

    Refit the drawer and restore power.

Buy the part

Get the right replacement

Buy the part

Oven door hinges

Opens Amazon in a new tab. Where’s my model number?

What to look for

  • Your range's model number. Hinges are specific to the door and body.
  • A pair, or two of the same hinge. Some kits include new springs.

Know your limits

When to call a pro

Stop and call a pro if

  • The front frame or the slots the hinges fit into are bent or torn.
  • The door glass is cracked or the door itself is warped.
  • On your model the springs are inside the side panels and the sides have to come off.

FAQ

Oven door hinges questions

Do I really need to replace both hinges?

Yes, usually. Repair guides replace them in pairs so the hinges and springs match, and some hinge kits say the two must be replaced together to work properly.

My door is fine but heat leaks out. Is it the hinges?

If the door closes flat and the hinges move evenly, look at the door gasket instead. A torn or flattened gasket lets heat out around the edge.

How do I take the oven door off without hinge locks?

Some doors have no hinge locks and come off a different way. Your owner's manual shows how for your model.

Related

Keep going

Get the next fix before it breaks

A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.

We send it with Kit. Privacy