WhatsBusted
3D model of a defrost thermostat
Also called bimetal thermostat, defrost limit switch

Refrigerator defrost thermostat test and replacement

A small switch clipped to the freezer coil, and one of the cheapest parts in the refrigerator. The trick is testing it while it is cold.

Difficulty
Easy
Time
30 min–1 hr
Typical part cost
$15–$90Pro: $105–$200

Behind the same freezer panel as the defrost heater. Usually one clip and two wires, though some are spliced or built into the heater.

What it does

What the defrost thermostat does

The defrost thermostat, often called a bimetal, clips onto one of the tubes of the evaporator coil behind the freezer's rear panel. It is wired in series with the defrost heater.

While the coil is below freezing, the switch inside is closed, so the heater can run when defrost starts. Once the coil warms up enough to be clear of frost, the switch opens and cuts the heater off. That stops the defrost from heating the freezer.

Why it fails

The switch can stick open. Then the heater gets nothing, even when the defrost cycle calls for it, and frost piles up on the coil.

It can be hard to judge. A good one reads open at room temperature, which is exactly what a bad one reads too. It has to be cold to test properly.

Symptoms

Signs of a bad defrost thermostat

  • Coil iced over, heater tests good

    The evaporator coil is packed with ice, but the defrost heater shows a normal resistance. The thermostat is the next suspect.

    Full diagnosis
  • Fridge warm, freezer cold

    Ice on the coil blocks the cold air from reaching the fresh-food section first.

    Full diagnosis
  • Frost keeps coming back

    You defrost the freezer by hand, it works for a while, and the ice comes back.

    Full diagnosis

How to test it

Test the defrost thermostat before you buy

Cold continuity testMeter on Ω (continuity)
  1. Unplug the refrigerator and take off the freezer's rear panel while the coil is still cold. Do not let it warm up first.
  2. Disconnect the thermostat's two wires at its plug or terminals.
  3. Touch one probe to each wire.

A good thermostat, still cold, typically reads

Continuity (near 0 Ω) when cold, open when warm

Typical range. Check your part label or manual for the exact spec. Some need to be well below freezing to close, around 20°F. If yours warmed up, put it in the freezer for an hour or two, or in a cup of ice water with salt, and test again.

Good
Continuity while it is cold means the switch closes as it should. Test the heater and the defrost timer or control next.
Bad
Open (OL) while it is still frosty cold means it is stuck open. Replace it.

Safety first

Before you touch anything

  1. 1

    Unplug the refrigerator

    Pull the plug at the wall, or switch off its breaker, before you open the freezer panel.

  2. 2

    Gloves near the coil

    The evaporator fins are sharp and the tubes are thin. Wear gloves and never pry at ice with a tool.

Tools you'll need

Grab these first

Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works

See the full repair tool kit

Step by step

How to replace the defrost thermostat

  1. 1

    Unplug it and empty the freezer

    Unplug the refrigerator. Move frozen food into a cooler and take out the freezer shelves and baskets.

  2. 2

    Remove the rear panel

    Take out the freezer's rear panel screws, unplug any light or sensor wire, and lift the panel out.

  3. 3

    Find the thermostat

    Look along the top tubes of the coil for a small round or oval disc, about the size of a coin, clipped onto a tube. Two wires run from it, usually to the heater or a plug.

    Test it now, while it is cold.

    Tip. Photograph the wires and which tube it sits on. The new one goes back on the same tube.

  4. 4

    Disconnect and unclip it

    Unplug its wires. If they are spliced, cut them close to the old thermostat so you keep as much wire as possible.

    Unhook the spring clip and lift the thermostat off the tube.

  5. 5

    Match the new one

    Check the new thermostat against the old one: the same connector or wire ends, and the same clip. If yours was spliced, the kit should include sealed connectors made for the freezer.

  6. Buy the part

    Defrost thermostat

    Opens Amazon in a new tab. Where’s my model number?

    What to look for

    • The part number on the old thermostat, or the one in your model's parts list.
    • The same connector. Some come with a plug, others with bare leads for splicing.
    • Some models use a defrost heater with the thermostat built in. If yours does, buy the whole assembly.

    Universal bimetal thermostats exist, but their opening and closing temperatures differ. Use the one listed for your model.

  7. 6

    Clip it on and connect it

    Clip the new thermostat to the same tube, flat side against the tube, so it reads the coil temperature.

    Reconnect the plug, or join spliced wires with the sealed connectors from the kit. Keep the wires clear of the fan blade.

  8. 7

    Close up and power on

    Refit the rear panel, the shelves and the food, then plug the refrigerator back in.

Buy the part

Get the right replacement

Buy the part

Defrost thermostat

Opens Amazon in a new tab. Where’s my model number?

What to look for

  • The part number on the old thermostat, or the one in your model's parts list.
  • The same connector. Some come with a plug, others with bare leads for splicing.
  • Some models use a defrost heater with the thermostat built in. If yours does, buy the whole assembly.

Universal bimetal thermostats exist, but their opening and closing temperatures differ. Use the one listed for your model.

Know your limits

When to call a pro

Stop and call a pro if

  • New heater and thermostat, and the coil still ices over. The defrost control or the sealed system may be at fault.
  • You see oily spots on the coil or damaged tubing.
  • You are not comfortable splicing wires inside the freezer.

FAQ

Defrost thermostat questions

My new defrost thermostat reads open on the bench. Is it bad?

Probably not. They are supposed to read open at room temperature and close only when cold. Chill it in the freezer for an hour or two and test again.

Is it the defrost thermostat or the heater?

Test the defrost heater first: it gives a clear reading at any temperature. If the heater is fine, test this thermostat while it is cold. If both are good, look at the defrost timer or the control board.

Is it the same as the temperature control dial?

No. The dial or the keypad sets how cold the compartments are. The defrost thermostat only controls the defrost heater.

Related

Keep going

Get the next fix before it breaks

A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.

We send it with Kit. Privacy