Refrigerator evaporator fan motor test and replacement
Freezer cold, fresh food warm? This little fan is the usual suspect, and it sits behind one panel in the freezer.
- Difficulty
- Easy
- Time
- 30 min–1 hr
- Typical part cost
- $25–$150Pro: $200–$400
- Tools
- 5See the list
Empty the freezer, take off one panel, swap a motor held by a few screws and one plug. The fiddly part is the panel, not the fan.
What it does
What the evaporator fan does
The evaporator coil behind the freezer's rear panel is the only cold spot in the refrigerator. The evaporator fan sits next to it, pulls air across the coil, and pushes that cold air around the freezer and through a vent into the fresh-food section.
It usually runs whenever the compressor runs. On most models it also stops whenever a door is open, so it does not blow cold air into the kitchen. A door switch tells it when.
Top-freezer and side-by-side refrigerators both work this way. The fan is in the freezer in both, behind the rear panel: at the top of a top-freezer, and in the left column of a side by side.
Why it fails
The motor's bearings wear out. A worn motor often squeals or chirps for a while, then slows down or stops.
Ice can grab the blade. If the defrost system stops working, frost builds up on the coil until it reaches the fan. A fan that is frozen in place is a sign of a defrost problem, not a bad motor.
Symptoms
Signs of a bad evaporator fan
Freezer cold, fridge warm
The freezer still freezes, but the fresh-food section creeps up toward room temperature. With no fan, the cold stays near the coil.
Full diagnosisSqueal or chirp from the freezer
A high squeal or chirp from behind the freezer's rear panel that stops when you open the door points straight at this fan.
Full diagnosisNo air from the freezer vent
With the freezer door open and the compressor running, press the door switch in and hold a hand near the freezer vent. You should feel air moving. Nothing means the fan is not turning.
Both sections warm
On some models the fan has to run for the freezer to stay cold too. If both sections are warm and the compressor runs, the fan is still worth a look, after the condenser coil.
Full diagnosis
How to test it
Test the evaporator fan before you buy
- Wait until you hear the compressor running.
- Open the freezer door and press and hold the door switch with your finger.
- Listen and feel for air at the vents in the freezer. On a side by side, also check the vent between the sections.
Some newer refrigerators run the fan at different speeds or pause it on purpose. A short pause is normal.
- Good
- You hear the fan spin up and feel steady air. The fan is working. Look at the defrost system or the condenser fan next.
- Bad
- Silence, a buzz with no air, or a squeal. Unplug the refrigerator and move on to the hands-on check.
- Unplug the refrigerator and take off the freezer's rear panel (steps below).
- Look for ice around the blade and the coil. Then turn the blade gently by hand.
- Good
- The blade turns freely with no ice around it. Do the continuity test next.
- Bad
- The blade is stiff, grinds or wobbles: replace the motor. If it is locked in ice, the motor may be fine and the defrost system is the real problem.
- With the refrigerator unplugged, disconnect the fan motor's plug.
- Touch one probe to each terminal on the motor side of the plug.
A good motor typically shows
Continuity: a steady reading, not OL
Typical range. Check your part label or manual for the exact spec. Many newer fans are electronic motors that a resistance check cannot judge. For those, the listen-and-feel test and the spin test are the better checks.
- Good
- A steady reading means the windings are intact. If the motor still will not run, check for power at its plug and the door switch.
- Bad
- OL (open) means the motor is dead. Replace it.
Safety first
Before you touch anything
- 1
Unplug the refrigerator
Pull the plug at the wall, or switch off its breaker if you cannot reach the outlet. Setting the control to off does not cut power to the fan.
- 2
Gloves on near the coil
The aluminum fins on the evaporator coil are thin and sharp. Wear gloves, and do not chip or pry at ice with a tool. You can puncture a refrigerant tube.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexMost freezer rear panels and fan brackets use 1/4 in. hex screws.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareSome panels use Phillips or Torx screws instead.Typically $10–$25Shop this tool
- Digital multimeterΩ, V, µF, µAA quick continuity check confirms the motor windings are open before you buy one.Typically $25–$60Shop this tool
- Work glovesThe evaporator fins behind the panel are sharp.Typically $8–$20Shop this tool
- HeadlampThe freezer light goes out when you unplug the refrigerator.Typically $12–$30Shop this tool
Step by step
How to replace the evaporator fan
- 1
Unplug it and empty the freezer
Unplug the refrigerator. Move frozen food into a cooler so it stays frozen while you work.
Take out the freezer shelves and baskets so you can reach the back wall.
- 2
Take off the rear panel
The panel at the back of the freezer covers the coil and the fan. Remove its screws. On some models you first have to lift out the ice maker or unclip a light cover.
Tip the panel forward and lift it out. If it has a wire for a light or a sensor, unplug that first.
Tip. Take a photo before you pull anything. It saves guesswork when it goes back together.
- 3
Check the coil for frost
Look at the coil before you go further. A thin, even layer of frost is normal. A coil packed solid with white ice means the defrost system has failed.
If it is packed with ice, the fan may be fine. Let the ice melt with the doors open and towels down, then test the defrost heater and the defrost thermostat.
- 4
Unplug the fan motor
Follow the motor's wires to its plug and pull the two halves apart. Squeeze the locking tab if there is one. Pull on the plug, not the wires.
- 5
Remove the motor
The motor sits in a bracket or a plastic shroud held by two to four screws. Remove them and lift the motor and blade out together.
Pull the blade straight off the shaft. Some blades have a clip or a nut on the front.
- 6
Match the new motor
Compare the old and new motors: the shaft, the mounting holes and the plug should match. Move the blade, any rubber mounts and the bracket over from the old motor, in the same positions.
Push the blade on the same distance as the old one. If it sits too far forward or back it can hit the shroud.
Buy the part
Evaporator fan motor
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part number on the old motor's label, or the one your model's parts list gives.
- The same plug and mounting. Some kits include a new bracket or wiring adapter.
- Whether yours is a plain motor or an electronic one with a small circuit board. They are not interchangeable.
Universal fan kits exist, but fit and wiring vary a lot. The part matched to your model number is the safer buy.
- 7
Install it and plug it in
Set the motor back in place, replace the screws and reconnect the plug until it clicks.
Spin the blade by hand. It should turn freely without touching the shroud or any wires.
- 8
Refit the panel and power up
Reconnect any light or sensor wire, refit the rear panel and its screws, and put the shelves back.
Plug the refrigerator in. When the compressor starts, press the door switch and listen for the fan.
Tip. Give it up to 24 hours to pull back down to temperature before you judge the repair.
Buy the part
Get the right replacement
Buy the part
Evaporator fan motor
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part number on the old motor's label, or the one your model's parts list gives.
- The same plug and mounting. Some kits include a new bracket or wiring adapter.
- Whether yours is a plain motor or an electronic one with a small circuit board. They are not interchangeable.
Universal fan kits exist, but fit and wiring vary a lot. The part matched to your model number is the safer buy.
Know your limits
When to call a pro
Stop and call a pro if
- The new fan runs but the refrigerator still does not cool. The problem is likely in the sealed system or the controls.
- The coil keeps icing over solid after you have replaced the defrost parts.
- You see oily residue on the coil or tubing, or a refrigerant tube is damaged.
- The fan has power at its plug but a new motor still will not run, and you are not comfortable tracing wiring.
FAQ
Evaporator fan motor questions
How do I know it is the evaporator fan and not the condenser fan?
Listen in the right place. The evaporator fan is inside the freezer, behind the rear panel. The condenser fan is in the machine compartment at the bottom back. A freezer that stays cold with a warm fresh-food section usually points to the evaporator fan or the defrost system. Both sections warm points more to the condenser fan or the condenser coils.
Why does the fan stop when I open the door?
That is normal on most refrigerators. The door switch stops the fan so it does not blow cold air into the room. Press the switch with your finger and the fan should start again.
The blade was frozen in ice. Do I still need a new motor?
Maybe not. Ice reaching the fan usually means the defrost system failed. Melt the ice, then test the fan. If it spins and tests good, replace the failed defrost part instead, starting with the defrost heater and the defrost thermostat.
Can I run the refrigerator while I wait for the part?
It will not cool the fresh-food section properly without the fan. Keep perishables in a cooler with ice and check the temperatures with a thermometer.
Related
Keep going
- SymptomFreezer cold but fridge warmThe freezer still freezes but the fresh-food section warms up. All the cold comes from one coil in the freezer, so this usually means air is not moving: a stopped evaporator fan, an iced-over coil, or a blocked vent.Open guide
- SymptomRefrigerator making noiseClicks, pops, gurgles, hums and sizzles are usually normal. A squeal or chirp from the freezer points to the evaporator fan. A rattle or squeal from the bottom back points to the condenser fan. Repeated clicking with no cooling points to the start relay.Open guide
- SymptomRefrigerator freezer frosting upA frost-free freezer should never need defrosting by hand. Frost near the door usually means a leaking gasket. Thick ice behind the rear panel, on the coil, means the defrost heater, the defrost thermostat or the defrost timer has failed.Open guide
- Refrigerator partDefrost heaterThe defrost heater sits under the freezer's evaporator coil and melts off the frost every so often. When it burns out, the coil ices over, airflow stops and the fresh-food section warms up first.Open guide
- Refrigerator partDefrost thermostatThe defrost thermostat is a small temperature switch on the evaporator coil. It lets the defrost heater run only while the coil is cold. If it sticks open, the heater never gets power and the coil ices over.Open guide
- Refrigerator partDoor switchThe door switch is the small plunger the door presses when it closes. It turns the light off and, on many models, lets the evaporator fan run. A stuck switch can leave the light burning in a closed refrigerator or keep the fan off.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
