Refrigerator ice maker troubleshooting and replacement
Most ice makers that quit are not broken. Check the arm, the water and the freezer temperature first. If it really has died, the swap is three screws and one plug.
- Difficulty
- Easy
- Time
- 20–45 min
- Typical part cost
- $55–$125Pro: $100–$300
- Tools
- 3See the list
Most fixes are checks, not tools. Replacing the unit is a few screws and a plug, with the water shut off.
What it does
What the ice maker does
When the ice maker is ready for a new batch, the water inlet valve at the back of the refrigerator opens briefly and fills the mold through a fill tube.
Once the water has frozen, the ice maker pushes the cubes out into the bin. A wire shut-off arm or a paddle rests on the ice; when the cubes pile up high enough to lift it, the ice maker stops until you take some out.
Why it fails
Often nothing has failed. The shut-off arm is up or jammed by a clump of ice, the water supply valve is closed, or the freezer is too warm for the ice maker to start a cycle.
The fill tube can freeze solid, so no water reaches the mold.
The ice maker's own motor or control can fail. Then it neither fills nor ejects even with water, the arm down and a cold freezer.
Symptoms
Signs of a bad ice maker
No ice, arm up
The wire arm is raised or the paddle is blocked by a clump of ice. Lower it or clear the clump and wait a few hours.
Full diagnosisSmall or hollow cubes
Not enough water is reaching the mold: a partly closed supply valve or a valve that is failing.
Full diagnosisBuzzing but no water
A buzz from the back every so often with no water in the mold means the ice maker is calling for water and not getting it. Check the supply valve and the line.
Full diagnosisWater overflowing the mold
Ice glued into a block in the bin, or water spilling from the mold, usually points to the water valve or a refrigerator that is not level.
Full diagnosis
How to test it
Test the ice maker before you buy
- Make sure the ice maker is switched on: the wire arm should be down, or the on/off switch or control set to on.
- Check the freezer temperature. It should be close to 0°F. A warm freezer makes ice slowly or not at all.
- Make sure the water supply valve behind or below the refrigerator is fully open, and that the water filter is seated, or the bypass plug is in if you run without one.
- Look at the fill tube where water enters the mold. If it is plugged with ice, that is your problem.
- Good
- All four look right and the ice maker still makes nothing after a day. Move on to the water valve test, then the ice maker itself.
- Bad
- One of these was off. Fix it and give the ice maker up to a day to start producing again.
- Listen near the back of the refrigerator when the ice maker should be filling, or use the water dispenser if you have one.
- If the dispenser works but the ice maker gets no water, the ice maker side of the water valve or the fill tube is the suspect.
- If there is water to the mold but the ice maker never ejects or refills, the ice maker itself has failed.
- Good
- Water reaches the mold and the arm is down, but nothing happens: replace the ice maker.
- Bad
- No water reaches the mold: test the [water inlet valve](/refrigerator/water-inlet-valve) and check the fill tube for ice.
Safety first
Before you touch anything
- 1
Unplug the refrigerator
The ice maker's motor can start on its own. Unplug the refrigerator before you remove it.
- 2
Shut off the water
Close the water supply valve to the refrigerator so the fill tube cannot spill while the ice maker is out.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexMost ice makers are held by 1/4 in. hex screws.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareFor Phillips mounting screws on some models.Typically $10–$25Shop this tool
- HeadlampThe back of the freezer is dark with the power off.Typically $12–$30Shop this tool
Step by step
How to replace the ice maker
- 1
Unplug it and shut off the water
Unplug the refrigerator and close its water supply valve. Remove the ice bin and set it in the sink.
- 2
Remove the mounting screws
Most ice makers hang on two screws at the top and are held by one more at the bottom or front. Remove the lower screw and loosen the upper ones a few turns.
- 3
Lift it off and unplug it
Lift the ice maker up off the upper screws and ease it forward. Unplug its wiring harness from the socket at the back wall of the freezer.
- 4
Move parts over to the new one
Compare the old and new units. On some designs the shut-off arm, the wiring harness or a mounting bracket has to move to the new ice maker. Follow the kit's instructions.
Buy the part
Ice maker
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your refrigerator's model number. Ice makers differ in plug, mounting and mold shape.
- The part number on the old ice maker's label, often under its front cover.
- Whether the kit includes the shut-off arm and wiring harness, or you reuse yours.
Some ice makers have universal replacements that list many models. Make sure yours is on the list.
- 5
Plug in and hang the new one
Plug the harness into the back wall, hang the new ice maker on the upper screws and refit the lower screw. Tighten them all.
Check that the fill tube points into the mold's fill cup. If it misses, water ends up in the bin or on the floor.
- 6
Water on, power on, be patient
Open the water supply valve, plug the refrigerator in, put the bin back and lower the arm.
The first ice takes a few hours. Throw out the first couple of batches.
Buy the part
Get the right replacement
Buy the part
Ice maker
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your refrigerator's model number. Ice makers differ in plug, mounting and mold shape.
- The part number on the old ice maker's label, often under its front cover.
- Whether the kit includes the shut-off arm and wiring harness, or you reuse yours.
Some ice makers have universal replacements that list many models. Make sure yours is on the list.
Know your limits
When to call a pro
Stop and call a pro if
- The freezer will not get down near 0°F. That is a cooling problem, not an ice maker problem.
- The fill tube keeps freezing solid after you thaw it.
- Water leaks inside the wall behind the refrigerator, at the household supply line or valve.
FAQ
Ice maker questions
My new refrigerator makes no ice. Is it broken?
Probably not yet. A new refrigerator needs about a day or two to get cold enough, and the ice maker will not start a cycle until it reaches its own starting temperature.
How do I turn the ice maker off?
Lift the wire arm until it clicks up, or use the on/off switch or control. Do that if you shut off the water, or the ice maker will keep calling for it.
Why is my ice maker making small or hollow cubes?
Too little water is reaching the mold. Check that the supply valve is fully open, replace a clogged water filter, and if that does not help, test the water inlet valve.
Related
Keep going
- SymptomRefrigerator ice maker not making iceThe ice maker makes no ice, or only small, hollow cubes. Check the shut-off arm, the water supply and the freezer temperature first. After that, the water inlet valve and the ice maker itself are the parts that fail.Open guide
- SymptomRefrigerator leaking waterWater under the crisper drawers or on the floor in front usually means a clogged or frozen defrost drain. Water at the back, on models with ice and water, points to the water line, the inlet valve or the filter.Open guide
- Refrigerator partWater inlet valveThe water inlet valve sits at the bottom back of the refrigerator. When the ice maker or the dispenser asks for water, a coil in the valve opens it. A dead coil means no water; a valve that will not close fully can drip or overfill the ice maker.Open guide
- Refrigerator partDefrost heaterThe defrost heater sits under the freezer's evaporator coil and melts off the frost every so often. When it burns out, the coil ices over, airflow stops and the fresh-food section warms up first.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
