Ice maker not making ice
Most of the time nothing is broken: the arm is up, the water is off or the freezer is too warm. Three minutes of checks come before any parts.
Check these first
Five-minute checks, no tools
Ice maker on, arm down
Lower the wire arm or switch the ice maker on. Break up any clump of ice that is holding the arm up.
Water valve open
Make sure the supply valve behind or below the refrigerator is fully open and the line is not kinked.
Freezer near 0°F
Set the freezer to 0°F and check it with a thermometer. A warm freezer makes ice slowly or not at all.
Filter or bypass plug in
Replace a clogged water filter. If you removed the filter, the bypass plug has to be in its place.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Shut-off arm or ice maker
Water reaches the mold but the ice maker never ejects or refills, or the arm is up or jammed.
Fix the ice maker20–45 min$55–$125 - 2DIY fix
Water inlet valve
No water reaches the mold even with the supply open, or the cubes are small and hollow. A coil may be open.
Fix the water valve30 min–1 hr$20–$200 - 3DIY fix
Freezer too warm
The freezer will not get down near 0°F, so the ice maker never starts. Fix the cooling first: see refrigerator not cooling.
What's happening
What your refrigerator is doing
To make ice, the ice maker needs three things: power and its shut-off arm down, water from the inlet valve at the back of the refrigerator, and a freezer cold enough to start a cycle.
If the freezer is too warm, the ice maker waits. If the arm is raised or jammed by a clump of ice, it thinks the bin is full. If the water valve is closed or the filter is clogged, it fills with little or nothing.
A fill tube frozen solid also stops water from reaching the mold.
Know your limits
When to call a pro
Stop and call a pro if
- The freezer will not get down near 0°F. That is a cooling problem.
- The leak or shutoff problem is in the household water line, not the refrigerator.
- The fill tube keeps freezing solid after you thaw it.
FAQ
Common questions
How long does a new ice maker take to make ice?
A new refrigerator needs about a day or two to get cold enough. After you replace an ice maker, the first ice usually takes a few hours. Throw out the first couple of batches.
Why does my ice maker buzz?
A short buzz while it fills is normal. A buzz about every 15 minutes with no water means it is calling for water and not getting it: check that the supply is turned on.
Can I reset my ice maker?
Many have a reset or test button, or reset when you raise and lower the arm or turn the ice maker off and on. Your owner's manual will say which. Unplugging the refrigerator for a minute is a safe general reset.
Related
Keep going
- SymptomRefrigerator leaking waterWater under the crisper drawers or on the floor in front usually means a clogged or frozen defrost drain. Water at the back, on models with ice and water, points to the water line, the inlet valve or the filter.Open guide
- SymptomRefrigerator not coolingThe freezer and the fresh-food section are both too warm. The usual causes are a dirty condenser coil, a stopped condenser fan, a failed start relay or an iced-over evaporator coil. The sealed system is the last thing to suspect, not the first.Open guide
- Refrigerator partIce makerThe ice maker fills a mold with water, freezes it, drops the cubes into the bin and stops when the bin is full. A raised shut-off arm, a closed water valve or a warm freezer stop it just as surely as a failed unit.Open guide
- Refrigerator partWater inlet valveThe water inlet valve sits at the bottom back of the refrigerator. When the ice maker or the dispenser asks for water, a coil in the valve opens it. A dead coil means no water; a valve that will not close fully can drip or overfill the ice maker.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
