How to clean a heat pump water heater air filter
Good news: this is the easiest job on a heat pump water heater. Ten minutes, a vacuum or a sink, and the filter light goes out.
- Difficulty
- Anyone can do it
- Time
- 10–30 min
- Typical part cost
- $0Pro: $100–$250
- Tools
- 1See the list
No parts and usually no tools. The only things to get right are turning the power off first and letting the filter dry before it goes back in.
What it does
What the air filter does
A heat pump water heater does not make heat, it moves it. A fan in the top section pulls room air across a cold coil filled with refrigerant. The coil takes heat out of that air, and the compressor moves it into the water in the tank.
The air filter sits where that air comes in. It catches dust and lint so they do not coat the coil. Where it is varies by model: often on the top of the unit or in a slot on the air intake.
Why it fails
A filter does not break, it fills up. A dusty filter restricts the airflow, and the heat pump has a harder time doing its job efficiently.
Many units watch for this. When the filter gets too dirty they light a filter alert, and some switch to electric mode, heating with the elements only. You still get hot water, but the energy savings are gone.
Filters do not seal tightly in their slots, so some air always slips past. A filter left dirty for a long time lets more dust through to the coil.
Symptoms
Signs of a bad air filter
Filter light or alarm
Many units show a filter alert on the display when the filter needs cleaning. Clean it, then reset the alert.
It switched to electric mode
Some units drop to electric only when the filter is too dirty. Hot water keeps coming, but your electric bill goes up.
Full diagnosisDust you can see
Pull the filter and look. A gray layer of dust and lint on it means it is due.
How to test it
Test the air filter before you buy
- Turn the water heater off as in step 1 below.
- Take the filter out of its slot or from under its grille.
- Look at both sides of the mesh.
- Good
- The mesh is clean and you can see through it. Put it back and check again next month.
- Bad
- Dust and lint coat the mesh. Clean it with the steps below.
Safety first
Before you touch anything
- 1
Standby, then power off
Put the water heater in standby with its power button if it has one, then turn off its breaker at the panel, or unplug it if it plugs into a wall outlet. The fan can start on its own while the power is on.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Shop vacuumA vacuum with a dust brush attachment lifts the dust off the filter. A household vacuum works too.Typically $40–$90Shop this tool
- HeadlampOptionalHelps you find the filter and its latch in a dark garage or basement.Typically $12–$30Shop this tool
Step by step
How to clean the air filter
- 1
Turn off the power
Press the power button to put the water heater in standby, if it has one. Then turn off its breaker at the main panel. It is usually a double breaker labeled water heater. If your heater plugs into a wall outlet, unplug it instead.
- 2
Find the filter
Look on the top of the heat pump section first. On other models the filter slides into a slot on the air intake grille. Your manual's maintenance page shows exactly where.
- 3
Take the filter out
Release any latch or tab and lift or slide the filter out. Go slowly so the dust stays on the filter.
Note which way it faces so it goes back the same way.
- 4
Clean it
For light dust, run a vacuum's dust brush over both sides.
For heavier dirt, wash it gently in a sink with mild soap and water, then rinse it clean.
- 5
Let it dry completely
Shake off the water and let the filter air dry before it goes back in.
While it dries, look it over. If the mesh is torn or the frame is cracked, order the filter your manual lists for your model number.
Buy the part
Heat pump air filter
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Most filters are washable and reusable, so you only need a new one if yours is torn, cracked or lost.
- The part number your manual's parts list gives for your model. Where the filter sits and its shape vary by model.
- 6
Put the filter back
Slide or set the dry filter back in its place, facing the same way it came out, and close any latch.
- 7
Power on and reset the filter alert
Turn the breaker back on, or plug it back in, and take the heater out of standby.
If the display still shows a filter alert, reset it. On many units you press and hold the filter button for a few seconds. Check your manual for yours.
If it had dropped to electric mode, it goes back to the mode you had set. Some units finish the heating cycle they are in on the elements first.
Buy the part
Get the right replacement
Buy the part
Heat pump air filter
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Most filters are washable and reusable, so you only need a new one if yours is torn, cracked or lost.
- The part number your manual's parts list gives for your model. Where the filter sits and its shape vary by model.
Know your limits
When to call a pro
Stop and call a pro if
- The filter alert comes back within a few days of a cleaning and reset. That can point to a different problem.
- The filter is clean but the heater keeps running in electric mode or shows a fault code.
- Dust has got past the filter onto the evaporator coil behind it. The coil is part of the sealed refrigerant system, so leave the fins alone and have a pro look.
- The fan is loud, knocking or not running. See the evaporator fan guide.
FAQ
Heat pump air filter questions
How often should I clean the filter?
Check it every month or two and clean it whenever it looks dusty or the filter light comes on. Guidance runs from every few months to at least once a year, so follow your manual.
Should I vacuum it or wash it?
Either works. A vacuum's dust brush handles light dust. For heavier dirt, wash it gently with mild soap and water. Always let it dry completely before you put it back.
Why did my heat pump water heater switch to electric mode?
A dirty filter is one of the usual reasons. Many units sense the clogged filter and heat with the elements only, which uses a lot more electricity. Clean the filter and reset the alert, and it goes back to the mode you had set.
If the filter is clean and it still runs on electric only, the heat pump section may have a fault. Check the display for a code and see your manual.
The filter light came back right after I cleaned it. Why?
Some manufacturers say a filter alarm that returns within a few days of cleaning and resetting can mean a separate problem. Make sure the filter is fully seated and the alert was reset, then call for service if it comes back.
Related
Keep going
- SymptomHeat pump water heater slow to recoverHeat pump water heaters only. The hot water runs out and takes a long time to come back. Check the operating mode, the air filter, the room's size and temperature, and the backup heating elements.Open guide
- Water heater partHeat pump condensate drainHeat pump (hybrid) water heaters only. The coil in the top pulls water out of the air, and the condensate drain carries it away through fittings on the unit and a line to a drain. When it clogs, water spills down the unit and the heat pump stops.Open guide
- Water heater partHeat pump evaporator fan motorHeat pump (hybrid) water heaters only. The evaporator fan in the top section pulls room air across the coil so the heat pump can take heat from it. When the fan fails, the heat pump cannot run. Most of these heaters run on 240 V, so the power goes off and stays off, verified with a tester.Open guide
- Water heater partHeat pump sealed systemHeat pump (hybrid) water heaters only. The sealed system is the closed refrigerant loop that moves heat from the room air into the tank: the evaporator coil, the compressor and the tubing. A leak or a failed compressor stops the heat pump, and any repair means opening the loop, which is certified work.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
