Tankless water heater condensate neutralizer and drain hose
Good news: refilling the neutralizer is a yearly 30-minute job that happens outside the heater's cabinet. While you are there, a quick look at the drain hose heads off most condensate codes.
- Difficulty
- Easy
- Time
- 20–45 min
- Typical part cost
- $30–$105Pro: $150–$350
- Tools
- 4See the list
Two hose connections and a canister, all outside the cabinet. The only fiddly parts are matching your neutralizer's style and priming it before the heater runs.
What it does
What the neutralizer does
A condensing tankless heater pulls so much heat out of its exhaust that water vapor in it turns back to liquid. That condensate is acidic, typically around pH 3 to 5, and it can eat away at drain and sewer pipes.
It leaves the heater through a trap and a drain hose and runs through the neutralizer: a plastic canister or cartridge filled with limestone chips. The limestone raises the pH before the water reaches the drain.
Many local plumbing codes require condensate to be neutralized before it goes down the drain. Your local code office has the rule for your area.
Why it fails
The media is used up as it works. The more condensate runs through it, the faster it goes, and once it is spent the water leaves as acidic as it came in.
The drain hose can clog, kink, sag or end up with its outlet under water. Condensate then backs up, and the heater shows a condensate code or shuts down.
A neutralizer packed with old, crusted media can slow the flow until the overflow fitting starts to spill.
Symptoms
Signs of a bad neutralizer
A condensate code
Many condensing heaters show a code when condensate cannot drain. Look it up in your manual, then check the hose and the neutralizer first.
Full diagnosisWater spilling at the neutralizer
Water coming out of the overflow fitting or dripping around the canister means the flow through it is blocked.
A low pH reading
A test strip in the water leaving the neutralizer reads below about 6, or below the number in its instructions. The media is spent.
A year since the last refill
Most makers want fresh media once a year. Some neutralizers have a float that rises when it is time.
How to test it
Test the neutralizer before you buy
- Run the heater for a while with a hot tap open so condensate flows.
- Catch a little of the water coming out of the neutralizer's outlet in a clean cup.
- Dip a pH test strip in it and compare the color to the chart.
- Good
- About 6 or higher, or above the number in your neutralizer's instructions. The media is still working.
- Bad
- Below that. The media is used up. Refill or replace it.
- Follow the hose from the bottom of the heater, through the neutralizer, to the drain.
- Look for kinks, low spots where water sits, cracks, and an outlet that ends under water.
- Good
- It runs downhill the whole way, with no kinks or sags, and the end sits above the water in the drain.
- Bad
- Kinked, sagging, cracked or submerged. Fix the route or replace the hose with the same type and size.
Safety first
Before you touch anything
- 1
Power off
Unplug the heater or turn off its breaker, so it cannot fire and send condensate down the line while it is apart.
- 2
Close the gas shutoff
Turn the quarter-turn shutoff on the gas line to the heater so the handle sits across the pipe. It is the only gas part you touch.
- 3
Gloves and glasses
Condensate is acidic. Wear gloves and eye protection, and rinse any off your skin with water.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Multi-bit screwdriverPhillips, flat, squareLoosens hose clamps on the neutralizer's inlet and outlet.Typically $10–$25Shop this tool
- Adjustable wrench8–10 in.OptionalSome neutralizers have unions at each end that need a wrench to start.Typically $10–$25Shop this tool
- Bucket5 galCatches the condensate in the hose and canister when you take them apart.Typically $4–$10Shop this tool
- Nitrile glovesCondensate is acidic. Keep it and the old media off your skin.Typically $8–$15Shop this tool
- Safety glassesKeeps a splash of condensate out of your eyes.Typically $5–$15Shop this tool
- pH test stripsOptionalTells you whether the media is still working by testing the water coming out.Typically $5–$20Shop this tool
Step by step
How to refill the neutralizer and check the drain hose
- 1
Turn off the power
Unplug the heater, or turn off its breaker if it is wired in.
- 2
Close the gas shutoff
Turn the quarter-turn handle on the gas line under the heater so it sits across the pipe.
Careful. That handle is the only gas part you touch. Never loosen a gas fitting.
- 3
Find the neutralizer and trace the hose
The drain hose leaves the bottom of the heater and runs to the neutralizer, a canister or cartridge, usually mounted on the wall or sitting on the floor below it. A second hose runs from the neutralizer to a floor drain, a sink drain or a condensate pump.
Take a photo of the setup. Note which end the condensate goes in and which end it comes out. Many are marked with arrows.
- 4
Disconnect the hoses
Hold the bucket under the neutralizer. Loosen the hose clamps, or unscrew the unions at each end, and pull the hoses off. A little condensate will run out.
- 5
Take the neutralizer down
Lift the neutralizer out of its clips or bracket and carry it to a sink or over the bucket.
- 6
Refill the media or swap the cartridge
Refillable type: unscrew the end cap, dump out the old media, rinse the inside, fill it with new media and screw the cap back on.
Cartridge type: replace the whole cartridge with a new one. Sack type: swap the media sacks, keeping them clear of the inlet and outlet.
Use only the media your neutralizer's maker lists.
Buy the part
Condensate neutralizer
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The media or cartridge your neutralizer's maker lists. Check the label on the canister for its model.
- Enough for a full refill. Refillable canisters take a set amount, cartridges come ready to fit.
- If you are replacing the whole neutralizer, one sized for a tankless water heater with fittings that match your drain hose.
Some neutralizer makers sell generic limestone media, but use only what your neutralizer's instructions allow. The wrong media can clog or wear out fast.
- 7
Clean and check the drain hose
Flush both hoses with clean water and make sure nothing is stuck inside.
Check the route. The hose should run downhill from the heater to the neutralizer and on to the drain, about 1/4 in. of drop per foot, with no kinks or sagging loops. The end should sit above the water in the drain, not in it.
Replace a cracked or brittle hose with the same type and size of plastic tubing. Condensate corrodes metal drain pipe.
- 8
Mount the neutralizer and prime it
Put the neutralizer back in its clips the same way round as before, inlet and outlet where they were.
Prime it: pour clean water into the inlet until it runs out of the outlet. Your neutralizer's instructions say how.
- 9
Reconnect the hoses
Push the hoses back on, in to the inlet and out from the outlet, and tighten the clamps or unions. Check against your photo.
- 10
Gas on, power on, watch it drain
Turn the gas shutoff handle back in line with the pipe, then plug the heater in or turn on its breaker.
Run a hot tap for several minutes. Condensate should drip out of the neutralizer's outlet into the drain, with nothing leaking at the connections.
Write the date on the neutralizer so you know when the next refill is due.
Buy the part
Get the right replacement
Buy the part
Condensate neutralizer
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The media or cartridge your neutralizer's maker lists. Check the label on the canister for its model.
- Enough for a full refill. Refillable canisters take a set amount, cartridges come ready to fit.
- If you are replacing the whole neutralizer, one sized for a tankless water heater with fittings that match your drain hose.
Some neutralizer makers sell generic limestone media, but use only what your neutralizer's instructions allow. The wrong media can clog or wear out fast.
Know your limits
When to call a pro
Stop and call a pro if
- The condensate code stays on with a clear hose and a fresh neutralizer. The trap inside the heater may be blocked or need replacing, and that is inside the sealed cabinet.
- Water is dripping from inside the heater's cabinet, not from the hose or the neutralizer.
- Your heater has no neutralizer, or the condensate drains straight into a metal pipe. A plumber can tell you what your local code requires.
- The drain hose cannot be routed downhill to a drain. You may need a condensate pump installed.
- You smell gas at any point. Leave the house and call the gas utility from outside.
FAQ
Condensate neutralizer questions
How often should I replace the neutralizer media?
Most makers say once a year, and sooner if the heater runs a lot or the pH test reads low. Some neutralizers have a float that rises when the media is spent.
Does my tankless heater have a neutralizer?
Condensing gas tankless heaters are the ones with a condensate drain hose leaving the bottom of the unit, and it should run through a neutralizer. The condensate comes from the burner's exhaust. Electric tankless heaters burn nothing and have no exhaust or vent, so they have no condensate to neutralize.
What happens if I skip it?
The acidic condensate goes straight into your drain, where it can corrode metal pipes over time. It may also break local plumbing code, and at least one neutralizer maker does not cover problems caused by media that was never replaced.
Why does my heater show a condensate code?
Usually because condensate cannot drain: a clogged or kinked hose, a hose end sitting under water, or a blocked neutralizer. Check those first. If the code stays, the trap inside the heater may need a pro.
Related
Keep going
- SymptomTankless water heater showing an error codeTankless gas and electric water heaters only. The display shows a code and the hot water stops or comes and goes. Note the code, look it up in your manual, then check gas, water valves, the inlet filter and scale.Open guide
- Water heater partDescaling flushTankless gas and electric water heaters only. Hard water leaves scale inside the heat exchanger or heating chambers. A yearly flush with a pump and descaling solution through the isolation valves' service ports dissolves it.Open guide
- Water heater partInlet filter screenTankless gas and electric water heaters only. A small mesh screen at the cold water inlet catches grit before it reaches the flow sensor and heat exchanger. When it clogs, hot water flow drops and the heater can stop firing.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
