Tankless water heater error code? Start here
An error code is the heater telling you what it noticed. Write it down, look it up, and work through the easy checks before you call anyone.
Check these first
Five-minute checks, no tools
Write down the code
Note the exact code on the display, then look it up in your owner's manual or the manufacturer's support pages for your model. Codes are not the same from brand to brand.
Reset or power-cycle once
Use the reset your manual describes, or turn the unit off at its switch or breaker, wait about 30 seconds and turn it back on. Do it once. If the same code comes back, the cause is still there.
Gas shutoff open (gas)
The handle on the gas line to the heater should sit in line with the pipe. On propane, check that the tank is not empty. If you smell gas, leave the house and call your gas utility from outside.
Isolation valves fully open
The hot and cold valves under the heater should be fully open for normal use. A valve left partly closed after a flush cuts the flow the heater needs.
Inlet filter clean
A small screen where cold water enters the heater catches grit. When it clogs, flow drops and some heaters throw a code. See the [inlet filter guide](/water-heater/tankless-inlet-filter).
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Scale in the heat exchanger
In a hard water area, minerals coat the inside of the heat exchanger or heating chambers. The heater runs hotter to keep up, and overheat or flow codes follow. A flush with a descaling solution through the service ports usually clears it.
Fix the descaling1.5 hr–2.5 hr$10–$50 - 2DIY fix
Clogged inlet filter
Flow has dropped at every tap and the code points to water flow. A screen packed with sediment starves the heater of water. Turning off the water and rinsing the screen is a quick fix.
Fix the inlet filter15–30 min$5–$30 - 3Call a pro
Gas supply off or interrupted (gas)
An ignition or no-flame code right after gas work, a propane delivery or a closed shutoff. Check that the shutoff is open and the propane tank has gas. Air left in the line after gas work has to be purged by a gas technician.
- 4DIY fix
Blocked condensate drain (gas)
A condensing gas unit makes water as it runs, which drains out through a hose and a neutralizer. If that path clogs, the unit can shut down with a drain code. See the condensate neutralizer guide.
Fix the neutralizer20–45 min$30–$105 - 5DIY fix
Flow sensor
Water runs, but the heater never sees it, so it never fires, or it shows a flow code with a clean filter and open valves. Debris in the sensor's turbine, or a failed sensor, is the usual reason.
Fix the flow sensor45 min–1.5 hr$25–$65 - 6Call a pro
Igniter or flame rod (gas)
Gas is on and flow is fine, but the unit keeps showing an ignition or flame failure code. A worn igniter or a coated flame rod can cause it. They sit in the sealed combustion chamber, so this is work for a pro.
- 7Call a pro
Blocked vent (gas)
Codes about combustion or airflow, especially after a storm or a long idle spell. Nests and debris can block the vent or air intake outside. Look from the outside only. Vent work is for a pro.
- 8DIY fix
Control board
A code the manual says points to the controls, or a display that stays blank with power on. Rule out everything else first, because a board is the most expensive guess.
Fix the control board30 min–1.5 hr$50–$200
What's happening
What your water heater is doing
A tankless heater watches itself the whole time it runs. When something is out of range, like no flame, too little water flow, an overheated heat exchanger or a blocked drain, it stops heating and shows a code on its display.
The codes are different on every brand and model, so the same number can mean two different things on two heaters. The owner's manual for your model lists what each code means and what to check first.
Many codes trace back to simple things: the gas shutoff closed, an isolation valve left partly closed after a flush, a clogged inlet filter, or scale built up inside the heat exchanger in a hard water area. Others point to the ignition or a sensor, which is work for a pro.
No code, but the water goes hot, cold, hot? See cold water sandwich. No hot water at one low-flow tap? See no hot water at low flow.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas. Do not touch switches. Leave the house and call your gas utility from outside.
- The same code comes back after a reset and the easy checks.
- The code points to ignition, flame sensing, the gas valve or venting.
- Gas line work was just done and the heater will not light. Air in the line has to be purged by a gas technician.
- Never jump out a fuse or a sensor to keep the heater running. It removes a safety circuit.
FAQ
Common questions
Where do I find what my tankless error code means?
In the owner's manual for your exact model, and on the manufacturer's support site. Codes differ between brands, so a list for another heater will not help.
Can I just reset the code?
Once, yes. Many manuals list a reset or a power-off and power-on. If the code returns, the reset did not fix anything, and you need to find the cause.
Can hard water cause tankless error codes?
Yes. Scale inside the heat exchanger hurts heat transfer, so the heater runs hotter to keep up and can trip overheat or flow codes. A descaling flush usually clears it, and a softener or regular flushing keeps it from coming back.
Is it safe to keep using the heater with an error code?
Some codes are warnings and the heater keeps running. Others shut it down until the problem is fixed. Never bypass a sensor to get it going again.
Related
Keep going
- SymptomTankless water heater scale buildupTankless gas and electric water heaters only. Temperature swings, weaker hot water, rising bills or a scale or overheat code in a hard water area. Scale in the heat exchanger is the usual reason, and a flush clears it.Open guide
- SymptomTankless water heater: no hot water at low flowTankless gas and electric water heaters only. Hot water works at full flow but not at a trickle or at one low-flow fixture. The flow is below the heater's minimum activation flow, or something is cutting flow.Open guide
- SymptomTankless water heater goes hot, cold, then hot againTankless gas and electric water heaters only. The shower runs hot, turns cold for a few seconds, then hot again, often after you shut the water off and turn it back on. Check flow, the fixture and the filter.Open guide
- SymptomWater heater not heating: no hot waterEvery hot tap runs cold. On an electric heater it is usually power, a tripped high-limit reset, an element or a thermostat. On a gas heater, start with the gas supply and the pilot.Open guide
- Water heater partDescaling flushTankless gas and electric water heaters only. Hard water leaves scale inside the heat exchanger or heating chambers. A yearly flush with a pump and descaling solution through the isolation valves' service ports dissolves it.Open guide
- Water heater partInlet filter screenTankless gas and electric water heaters only. A small mesh screen at the cold water inlet catches grit before it reaches the flow sensor and heat exchanger. When it clogs, hot water flow drops and the heater can stop firing.Open guide
- Water heater partFlow sensorTankless gas and electric water heaters only. The flow sensor is a little turbine on the cold inlet that tells the control board water is moving. When it sticks or fails, the heater never fires, or cuts out mid-shower.Open guide
- Water heater partCondensate neutralizerCondensing tankless gas water heaters only. Their acidic condensate runs down a drain hose through a canister of limestone media that neutralizes it. The media gets used up and needs refilling about once a year.Open guide
- Water heater partTankless igniter and flame rodTankless gas water heaters only. The igniter sparks the burner alight and the flame rod proves the flame is there. When either fails, the unit stops with an ignition or flame failure code. Service is pro work.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy