Scale buildup in your tankless water heater
Hard water leaves minerals behind every time it is heated. In a tankless heater they collect in a small space, so a flush now and then keeps it running well.
Check these first
Five-minute checks, no tools
Compare hot and cold flow
Open a faucet on full cold, then full hot. If only the hot side is weak, look inside the heater: scale or a clogged inlet filter. If both are weak, the problem is in the house supply, not the heater.
Look up any code
If the display shows a code, note it and check your manual. Some codes point straight to scale or overheating. Others mean something else, so do not assume.
When was it last flushed?
Check your records or a service sticker. In hard water, a heater that has gone a year or more without a flush is a strong suspect.
Inlet filter clean
With the power and water off, rinse the small screen where cold water enters the heater. A clogged screen also cuts flow and can look like scale trouble. See the [inlet filter guide](/water-heater/tankless-inlet-filter).
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Scale in the heat exchanger or heating chambers
Hard water, a long time since the last flush, and slowly worsening swings or codes. A descaling flush through the isolation valves' service ports is the fix, and regular flushes keep it from coming back.
Fix the descaling1.5 hr–2.5 hr$10–$50 - 2DIY fix
Clogged inlet filter
Flow is weak at every tap. Sediment and flakes of scale collect on the inlet screen and cut the flow. Clean it before and after a flush.
Fix the inlet filter15–30 min$5–$30 - 3DIY fix
Fouled flow sensor
The heater fires late or cuts out even after a flush and with a clean filter. Debris in the flow sensor's turbine can keep it from reading the flow properly.
Fix the flow sensor45 min–1.5 hr$25–$65
What's happening
What your water heater is doing
Hard water carries calcium and magnesium. When it is heated, some of those minerals come out of the water and stick to the hot surfaces inside the heater as scale. In a gas tankless that is the heat exchanger. In an electric one it is the heating chambers.
Scale insulates the metal from the water, so heat moves across more slowly. The heater has to run hotter to hold the temperature you set, which wastes energy, and a sudden spike in outlet temperature can trip a code.
The signs build slowly: hot water that swings between hot and cool, less hot water than before, higher energy bills, and in time an error code that the manual ties to scale or overheating.
How fast it builds depends on how hard your water is. A flush with a descaling solution through the service ports on the isolation valves removes it. A water softener slows it down a lot.
Know your limits
When to call a pro
Stop and call a pro if
- A code keeps coming back after a flush.
- You do not have, or do not want to rent, a pump and hoses for the flush.
- Your water is very hard and you want a softener or scale filter added.
- A valve or fitting under the heater leaks after a flush.
FAQ
Common questions
How often should I descale a tankless water heater?
It depends on how hard your water is, so follow your manual. In hard water many heaters need it about once a year. Soft water can go much longer.
Can I use vinegar to descale my tankless heater?
Some manufacturers call for food-grade white vinegar, pumped through the heater for about an hour. Check your manual first, because some name a specific descaling solution.
Will a water softener stop scale?
A softener removes most of the calcium and magnesium that form scale, so it slows buildup a lot. Prevention beats descaling over and over.
Related
Keep going
- SymptomTankless water heater showing an error codeTankless gas and electric water heaters only. The display shows a code and the hot water stops or comes and goes. Note the code, look it up in your manual, then check gas, water valves, the inlet filter and scale.Open guide
- SymptomTankless water heater goes hot, cold, then hot againTankless gas and electric water heaters only. The shower runs hot, turns cold for a few seconds, then hot again, often after you shut the water off and turn it back on. Check flow, the fixture and the filter.Open guide
- SymptomTankless water heater: no hot water at low flowTankless gas and electric water heaters only. Hot water works at full flow but not at a trickle or at one low-flow fixture. The flow is below the heater's minimum activation flow, or something is cutting flow.Open guide
- Water heater partDescaling flushTankless gas and electric water heaters only. Hard water leaves scale inside the heat exchanger or heating chambers. A yearly flush with a pump and descaling solution through the isolation valves' service ports dissolves it.Open guide
- Water heater partInlet filter screenTankless gas and electric water heaters only. A small mesh screen at the cold water inlet catches grit before it reaches the flow sensor and heat exchanger. When it clogs, hot water flow drops and the heater can stop firing.Open guide
- Water heater partFlow sensorTankless gas and electric water heaters only. The flow sensor is a little turbine on the cold inlet that tells the control board water is moving. When it sticks or fails, the heater never fires, or cuts out mid-shower.Open guide
- Water heater partTankless heating elementTankless electric water heaters only. The unit heats water as it flows through heating chambers, each with its own element. A burned-out element tests open on a meter and swaps out with the power and water off.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy