Heat strips not working on your air handler
The heat pump runs, but on a cold day the house never catches up, or Emergency heat blows cool air. The backup heat strips have stopped. Start with the breakers and the filter.
Check these first
Five-minute checks, no tools
Thermostat set to Heat
Set the thermostat to Heat a few degrees above the room temperature. To test the strips alone, switch it to Emergency heat for a few minutes and feel the air at a vent. Then switch back, because strip heat costs more to run.
Every breaker on
Check every breaker for the air handler in the house panel, plus any breakers on the front of the air handler and the disconnect switch beside it. The heat kit may be on a breaker of its own. If one trips again right away, leave it off and call a pro.
Filter clean
A clogged filter cuts the airflow over the strips. They overheat and their limit switches shut them off. Hold the filter up to a light and replace it if you cannot see through it.
Blower running
The strips need the blower moving air over them. If no air comes out of the vents at all, the strips are not the problem yet. See [no airflow](/air-handler/symptoms/no-airflow) first.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Heat strip breaker off or tripped
The heat pump and blower run, but a breaker that feeds the strips, in the panel or on the heat kit, is off or tripped. Reset it once. A breaker that trips again as soon as the strips come on points to a short in a strip or its wiring, so leave it off and call a pro.
- 2DIY fix
Heat sequencer
Power reaches the air handler and the thermostat calls for heat, but some or all of the strips never come on. A sequencer that has failed does not close its contacts, so those strips stay cold. A sequencer stuck closed can also leave strips running after the call ends.
Fix the sequencer30 min–1.3 hr$40–$55 - 3DIY fix
Burned-out heat strip
One element has broken open, so it reads open on a meter with the power off. If the other strips still work, you may get some heat, just not enough.
Fix the heat strips1 hr–2.5 hr$115–$275 - 4DIY fix
Strip limit tripped by low airflow
The strips come on, then cut out after a few minutes. Not enough air is crossing them, so they get too hot and the limit switch opens. A clogged filter is the usual reason. Fix the airflow before you blame the limit.
Fix the air filter5–15 min$5–$25 - 5DIY fix
Control board
The thermostat calls for heat, but the low-voltage signal never reaches the sequencer. The board or its wiring may not be passing the call through.
Fix the control board30 min–1.5 hr$55–$270 - 6DIY fix
Thermostat setup or wiring
The thermostat is not set up for a heat pump with backup heat, or the wire for auxiliary heat is loose. This can happen after a new thermostat goes in.
What's happening
What your air handler is doing
A heat pump heats the house by moving heat in from outside. On the coldest days, and while the outdoor unit defrosts, the thermostat calls for auxiliary heat: electric resistance heat strips in the air handler.
Emergency heat is a thermostat setting that shuts the heat pump off and runs the strips alone. It is the easiest way to test them. If Emergency heat blows cool air, the strips are not heating.
When the thermostat calls for strip heat, a low-voltage signal reaches the heat sequencer. It switches the strips on one stage at a time, so they do not all draw power at once. Limit switches on the strips cut them off if they overheat.
The strips run on 240 V and draw a lot of current. Depending on the size of the heat kit, the air handler may be fed by more than one breaker in the house panel, and many heat kits also have breakers of their own on the front of the kit.
Know your limits
When to call a pro
Stop and call a pro if
- A heat strip breaker trips again as soon as the strips come on.
- You see smoke, scorch marks or melted wire near the strips or the sequencer, or you smell burning. Turn every breaker off and leave them off.
- You are not comfortable working in a 240 V cabinet with more than one power supply, or you cannot confirm with a tester that every circuit is dead.
- The strips run very often in mild weather. The heat pump itself may not be keeping up, or it may be defrosting too often.
FAQ
Common questions
What is the difference between auxiliary heat and emergency heat?
Auxiliary heat comes on by itself when the heat pump needs help. Emergency heat is a setting you choose by hand. It turns the heat pump off and runs only the backup heat. Use it only when the heat pump is not working, because it costs much more to run.
Is it normal for the heat strips to come on during defrost?
Yes. While the outdoor unit defrosts, most systems turn the strips on so the house does not get a blast of cool air. They turn off again when defrost ends.
Why does the heat strip breaker keep tripping?
A breaker that trips the moment the strips come on usually means a shorted strip or a wiring fault. Leave it off and have a pro find the cause. Resetting it again and again does not fix the fault.
Can I test the heat strips myself?
With every breaker and the disconnect off, and the power confirmed dead with a tester, a careful homeowner can check a strip with a multimeter. A good one shows continuity, an open one does not. The heat strips guide walks through it.
Related
Keep going
- SymptomAir handler not blowing air: no airflow from the ventsThe blower inside the air handler is not moving air. A humming motor that never spins points to the run capacitor. Silence points to power, the blower door switch, a tripped float switch, the board or the motor. Ice on the coil can also block the air.Open guide
- Air handler partHeat sequencer and heat relaysAir handlers with electric heat only. The sequencer, or a set of heat relays on some units, switches the heat strips on in stages. When it fails, some or all of the strips never come on, even though they are fine.Open guide
- Air handler partElectric heat stripsAir handlers with electric heat only. The heat strips are coils of resistance wire on a rack inside the air handler. They back up the heat pump in cold weather and during defrost. When they fail, auxiliary and emergency heat stop working.Open guide
- Air handler partAir filterFor heat pump and central air handlers, including units with electric heat strips. The filter cleans the air before it reaches the blower and coil. A clogged one chokes airflow, which can freeze the coil in summer and trip the heat strips in winter. Check it monthly.Open guide
- Air handler partControl boardThe control board in an air handler takes the thermostat's signals and switches the blower and the electric heat. A blown fuse or a burned relay on it can stop the fan, the heat, or the whole system.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy