Gas stove burner won't light
Clicking but no flame is usually water, food or a crooked cap. No clicking at all points to the spark side. Either way, check the burner itself first.
Check these first
Five-minute checks, no tools
Knob on Lite
The igniter only sparks with the knob turned to the Lite position. If your range has a cooktop lock, make sure it is off.
Cap flat and centered
Lift the grate. The cap should sit flush and centered on the burner with almost no side-to-side play, and on the right burner.
Dry after cleaning
If you just cleaned or had a spill, let the burner dry fully. A hair dryer on a cool setting speeds it up.
Gas reaching the range
If no burner lights, with sparks, check that the gas shutoff is open and that your other gas appliances work.
Power on
No clicking at all on any burner: check the plug and the breaker.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Wet, dirty or misaligned burner
Clicks but no flame on one burner, especially after cleaning or a spill. Clean, dry and reseat the cap and head.
Fix the burner caps10–30 min$0 - 2DIY fix
Spark module
No spark, or weak and slow sparks, at several burners with everything clean and dry.
Fix the spark module30 min–1 hr$35–$110 - 3Call a pro
Cracked or dirty electrode
One burner sparks weakly or not at all. Look for a crack in the white porcelain beside the burner. Replacing an electrode means working near the burner's gas parts, so have a pro do it if you are unsure.
- 4Call a pro
Gas supply or burner valve
Sparks but no gas at the burner, or no gas at any burner. Gas valve and line work is for a pro or your gas supplier.
What's happening
What your range is doing
Turning a knob to Lite opens the burner's gas valve and starts the spark. Gas flows out of the ports in the burner head, under the cap, and the spark beside it lights it.
Water from a spill or a wash, or food in the ports, keeps the gas from reaching the spark. A cap that sits crooked, upside down or on the wrong burner does the same. These are the most common reasons a burner clicks without lighting.
If you hear no clicking at all, check that the range is plugged in and the breaker is on. If several burners spark weakly or not at all with everything clean and dry, the spark module is the likely cause.
Know your limits
When to call a pro
Stop and call a pro if
- You smell gas with the knobs off, or the smell stays after a burner is lit. Leave the house and call your gas supplier from outside.
- Gas flows at a burner but nothing ignites it after several seconds. Turn the knob off and let the gas clear before trying again.
- The flame is large, yellow and lazy, or lifts off the burner.
- A burner valve, gas tube or the gas line needs work.
FAQ
Common questions
Why does my burner light on only one side?
Some ports are blocked, or the cap is off-center. Clean the ports with a straight pin and reseat the cap flat and centered.
Can I light a gas burner with a match?
Some gas range manuals describe lighting the surface burners with a match during a power outage. Only do it if your manual describes it, and follow its exact steps.
All the burners click when I turn one knob. Is that a problem?
No. On many ranges every igniter sparks together. Only the burner you turned on gets gas, so only that one lights.
Related
Keep going
- SymptomGas stove keeps clickingThe igniters keep clicking after the burner lights, or click with every knob off. Moisture and a misaligned cap cause most of it. If it continues with everything dry and seated, a knob switch or the spark module has failed.Open guide
- SymptomOven not heatingThe oven will not heat, or barely warms. On an electric range the bake element is the usual cause, after the breaker. On a gas range a weak igniter is the most likely, after the gas supply. The sensor and the control come later.Open guide
- Range partBurner caps and headsGas ranges only. Each surface burner has a head with a ring of small ports and a cap that sits on top. Spills clog the ports, water from cleaning stops the spark, and a cap knocked off-center keeps the flame from catching. Cleaning and reseating them fixes most burners that will not light.Open guide
- Range partSpark moduleGas ranges only. The spark module makes the high-voltage pulses that spark at every burner when you turn a knob to Lite. A failing module gives weak, slow or no sparks at several burners, or clicks constantly. It is usually a few screws and a few plugs.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
