Refrigerator door gasket test and replacement
A torn or flattened seal lets warm, damp air in all day. The test takes a sheet of paper, and the fix takes no special tools.
- Difficulty
- Easy
- Time
- 30 min–1 hr
- Typical part cost
- $50–$130Pro: $75–$300
- Tools
- 2See the list
No special tools, just patience. The work is easing the new gasket into place all the way around and getting the wrinkles out.
What it does
What the door gasket does
Each door has a rubber or vinyl gasket with a magnetic strip inside. It pulls the door tight against the cabinet and keeps warm, humid kitchen air out.
Top-freezer refrigerators have one gasket on each of the two doors. Side-by-side refrigerators have a tall gasket on the freezer door and another on the fresh-food door.
Why it fails
Gaskets harden, tear and lose their shape with age. Food spills make them sticky and then brittle.
A door that sags, or a refrigerator that is not level, can stop a good gasket from sealing. Check that before you replace it.
Symptoms
Signs of a bad door gasket
The paper drags out easily
Close the door on a sheet of paper and pull it out. You should feel it drag. If it slides out freely at any spot, the seal is weak there.
Condensation or warm spots
Water beads on the inside walls or along the door edge, or one shelf is warmer than the rest.
Full diagnosisFrost near the door
Frost or ice that builds up near the door opening, rather than on the back wall, points to air leaking past the gasket.
Full diagnosisTorn, flat or hard
Look for splits at the corners, a flattened section, or a gasket that has pulled away from the door.
How to test it
Test the door gasket before you buy
- Clean the gasket and the cabinet face with warm, soapy water and dry them. Dirt alone can stop a seal.
- Close the door on a sheet of paper or a dollar bill and pull it out.
- Repeat every few inches all the way around each door, including the hinge side.
- Good
- You feel drag everywhere. The gasket seals. Look for another cause of the warmth or frost.
- Bad
- The paper slips out freely in one or more places. Try warming that spot and reshaping it, then test again. If it still does not seal, replace the gasket.
Safety first
Before you touch anything
- 1
Unplug the refrigerator
Unplug it while you work, so the light is off and the compressor is not fighting an open door.
- 2
Mind the door
Keep the door well supported while the gasket is off. Do not hang on it or let it swing.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Nut driver1/4 in. hexLoosens the retainer screws on gaskets that use them.Typically $6–$15Shop this tool
- Multi-bit screwdriverPhillips, flat, squareSome retainer screws are Phillips.Typically $10–$25Shop this tool
- Putty knifeStiff, 1-1/2 in.OptionalA plastic putty knife helps tuck a push-in gasket into its channel.Typically $5–$12Shop this tool
Step by step
How to replace the door gasket
- 1
Unplug it and clear the door
Unplug the refrigerator. Take the bins and shelves out of the door so it is lighter and you can see the gasket's edge.
- 2
Warm the new gasket
New gaskets arrive folded and creased. Soak the new one in warm water for a few minutes, or warm it with a hair dryer on low to medium, and lay it flat so it relaxes.
Buy the part
Door gasket
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your model number. Gaskets are sized to the door, and the freezer and fresh-food gaskets are different parts.
- The same mounting style: push-in or screw retainer.
- Sometimes the color matters, as gaskets come in white, black or gray to match the cabinet.
Cut-to-fit universal gaskets exist, but a gasket made for your door seals better and is easier to fit.
- 3
Find how the old one is held
Peel back the gasket's inner lip at a corner. Some gaskets push into a channel with no screws. Others sit under a metal retainer strip held by screws all around the door.
- 4
Remove the old gasket
Push-in type: pull the gasket straight out of its channel, starting at a corner.
Screw type: loosen the retainer screws a few turns, one side at a time, and slide the gasket out from behind the retainer. Loosen, do not remove, unless your manual says to.
Tip. Work one side at a time so the inner door panel stays lined up.
- 5
Clean the door edge
Wipe the channel or retainer area with warm, soapy water and dry it. Old residue stops the new gasket from seating.
- 6
Fit the new gasket
Start at a top corner. Press the gasket's lip into the channel, or tuck it behind the retainer, and work your way around the door, corners first, then the straight runs.
On a screw type, snug the screws once the whole gasket is in, a little at a time around the door.
- 7
Close it, check it, power up
Close the door and look for gaps or puckers. Warm any wrinkle with the hair dryer and press it flat, then close the door to let it set.
Do the paper test again all the way around, then plug the refrigerator in and reload the door.
Buy the part
Get the right replacement
Buy the part
Door gasket
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your model number. Gaskets are sized to the door, and the freezer and fresh-food gaskets are different parts.
- The same mounting style: push-in or screw retainer.
- Sometimes the color matters, as gaskets come in white, black or gray to match the cabinet.
Cut-to-fit universal gaskets exist, but a gasket made for your door seals better and is easier to fit.
Know your limits
When to call a pro
Stop and call a pro if
- The door sags or will not close square even with a new gasket. The hinge or the door needs adjusting.
- The new gasket seals but the refrigerator still runs warm.
- The inner door panel cracked or pulled loose while you worked.
FAQ
Door gasket questions
Can I fix a gasket instead of replacing it?
Sometimes. Clean it, then warm a flattened or wavy section with a hair dryer on low and reshape it with your fingers. If it is torn or still will not seal, replace it.
Why is there frost near the freezer door?
Frost close to the door opening usually means humid air is getting in past the gasket. Frost on the back wall, behind the panel, points to the defrost system instead. See frost building up.
Is the refrigerator level enough?
A refrigerator that is not level can keep the doors from sealing. Check your manual for how your model should be leveled, and adjust the leveling legs if the doors drift open.
Related
Keep going
- SymptomRefrigerator not coolingThe freezer and the fresh-food section are both too warm. The usual causes are a dirty condenser coil, a stopped condenser fan, a failed start relay or an iced-over evaporator coil. The sealed system is the last thing to suspect, not the first.Open guide
- SymptomRefrigerator freezer frosting upA frost-free freezer should never need defrosting by hand. Frost near the door usually means a leaking gasket. Thick ice behind the rear panel, on the coil, means the defrost heater, the defrost thermostat or the defrost timer has failed.Open guide
- Refrigerator partDoor switchThe door switch is the small plunger the door presses when it closes. It turns the light off and, on many models, lets the evaporator fan run. A stuck switch can leave the light burning in a closed refrigerator or keep the fan off.Open guide
- Refrigerator partDefrost heaterThe defrost heater sits under the freezer's evaporator coil and melts off the frost every so often. When it burns out, the coil ices over, airflow stops and the fresh-food section warms up first.Open guide
- Refrigerator partCondenser coilsThe condenser coil gives off the heat the refrigerator removes from your food. Dust, lint and pet hair on it hold that heat in, so the refrigerator runs longer and cools less. Cleaning it takes a vacuum and a soft brush.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
