French-door freezer drawer slides: fix a drawer that will not close
A freezer drawer that sticks, springs back or sits crooked is usually the basket, the load or a slide. Two of those cost nothing. The third is a Phillips screwdriver and an hour.
- Difficulty
- Easy
- Time
- 30 min–1 hr
- Typical part cost
- $15–$270Pro: $100–$400
- Tools
- 2See the list
Mostly unhooking and re-hooking parts. The work is lifting a heavy drawer front square and getting both slides to match.
What it does
What the drawer slides does
The freezer door is the front of a drawer. It bolts to two slides, one on each side, that roll in tracks on the cabinet walls and carry the basket in and out.
Rollers or glides on the slides take the weight. When they turn freely, the drawer runs smooth and square, and the door closes flat against its gasket.
Why it fails
Most drawers that will not close have nothing broken: the basket has come off its rails, food is packed above the fill line, or frost has formed in the slide track.
Rollers crack and slides bend or wear, especially with heavy loads. A drawer with a damaged slide drags, grinds or sits crooked.
A sheet of ice on the freezer floor or behind the basket comes from a blocked defrost drain. It can push the drawer out, but new slides will not cure it.
Symptoms
Signs of a bad drawer slides
Drawer will not close
The drawer springs back open, stops an inch short, or closes but does not seal.
Full diagnosisSits crooked
One side of the drawer front sits lower or farther out than the other. A roller or a slide on that side is damaged.
Full diagnosisHard to slide or grinding
The drawer drags, catches or grinds as it moves. Look for frost in the track and broken rollers.
Ice sheet behind the drawer
A layer of ice on the freezer floor or behind the basket. That is the defrost drain, so start with the frost buildup page.
Full diagnosis
How to test it
Test the drawer slides before you buy
- Make sure nothing is caught at the back or the sides.
- Pull the drawer partway open, then push it closed firmly without slamming. That lets the rollers settle back into their track.
- On models with a roller bar behind the drawer that links the two slides, check that the bar is still in place and rolling. Reseat it as your manual shows if it has come out.
- Good
- It closes flat and stays shut. You are done.
- Bad
- Still springs back or sits crooked. Do the visual check.
- Open the drawer all the way.
- Check that the basket sits on its rails and that food is below the fill line or the basket's top edge.
- Look along each slide and its track for frost or ice, and for cracked or missing rollers.
- Look under and behind the basket for a sheet of ice.
- Good
- Basket reseated, load trimmed or frost melted, and the drawer runs smooth: no part needed.
- Bad
- A cracked roller or a bent slide: replace the slide. A sheet of ice: see [frost buildup](/refrigerator/symptoms/frost-buildup) before anything else.
Safety first
Before you touch anything
- 1
Unplug the refrigerator
Pull the plug before you take the drawer apart, so the freezer fan is not running while the opening is wide open.
- 2
Mind the weight
The drawer front is heavy and the slides can spring closed. Keep fingers clear of the tracks and support the front with both hands when it comes off.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Multi-bit screwdriverPhillips, flat, squareMost slide and drawer-front screws are Phillips.Typically $10–$25Shop this tool
- HeadlampLets you see into the slide tracks at the back of the freezer.Typically $12–$30Shop this tool
- Work glovesOptionalSlide edges and brackets can be sharp, and the metal is freezing cold.Typically $8–$20Shop this tool
Step by step
How to replace the drawer slides
- 1
Unplug it and empty the drawer
Unplug the refrigerator. Move the frozen food into a cooler so it stays frozen while you work.
- 2
Lift out the basket
Open both French doors so nothing is in the way, then pull the freezer drawer all the way out.
Lift out the upper basket, if your model has one, and then the main basket.
- 3
Check for ice on the floor
With the basket out, look at the freezer floor and the back wall. A flat sheet of ice means the defrost drain is blocked and melt water is refreezing. Fix that first: see frost buildup.
Frost in the slide tracks alone can be melted with the drawer open and towels down.
- 4
Take the drawer front off the slides
The drawer front is held to a bracket on each slide by screws. Support the front with one hand and remove the screws on both sides.
Lift the front up and off the slides and set it face down on a towel.
Tip. A second pair of hands makes this easier. The front is heavier than it looks.
- 5
Remove the old slide
Push the slide back in, then remove any screws holding it to the cabinet wall. Most slides then unhook from tabs on the wall: tip it and lift it free.
Note which slots it hooked into, so the new one goes in the same place.
- 6
Match the new slide
Slides are made left and right, so order the side you need by your model number. Replacing both at once keeps them matched, so the drawer runs square.
Where only a roller has broken, some models sell the roller or its axle on its own.
Buy the part
Freezer drawer slides
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your model number. Slides are made for specific models and specific sides.
- Left or right. Order a pair if both are worn.
- Whether you need the whole slide or just a roller or roller axle.
Slides are not universal. Buy the part matched to your model number.
- 7
Install the new slide
Hook the new slide into the same slots on the cabinet wall and refit its screws. Pull it out and push it in a few times: it should roll smoothly all the way.
Refit the drawer front on both slides and snug its screws, keeping the front square to the cabinet.
- 8
Basket in, close it and power up
Set the basket back on its rails, making sure its rollers or tabs sit in the track. Close the drawer: it should run smooth and close flat.
Close the drawer on a sheet of paper at a few points around the gasket. You should feel it drag. Then plug the refrigerator in and reload the food.
Buy the part
Get the right replacement
Buy the part
Freezer drawer slides
Opens Amazon in a new tab. Where’s my model number?
What to look for
- Your model number. Slides are made for specific models and specific sides.
- Left or right. Order a pair if both are worn.
- Whether you need the whole slide or just a roller or roller axle.
Slides are not universal. Buy the part matched to your model number.
Know your limits
When to call a pro
Stop and call a pro if
- Ice keeps forming on the freezer floor after you clear it. The defrost drain line needs a technician on many bottom-freezer models.
- The mounts or tabs on the cabinet wall that hold the slides are cracked or pulled out.
- The drawer runs smooth but its gasket does not seal. See the door gasket guide or call a pro if it is torn.
FAQ
Freezer drawer slides questions
Why won't my freezer drawer close all the way?
Most often the basket has slipped off its rails, food is stacked too high, or frost has formed in the slide track. Reseat the basket, trim the load and melt any frost. If it still will not close, look for a broken roller or bent slide.
There is ice under my freezer drawer. Is that the slides?
No. A sheet of ice on the freezer floor comes from melt water that cannot get down the defrost drain. It can push the drawer out, but the fix is the drain. Start with frost buildup.
Do I need to replace both slides?
It is the better choice if both are worn. Matched slides travel the same, which keeps the drawer square.
Related
Keep going
- SymptomFrench-door freezer drawer won't closeFrench-door and bottom-freezer refrigerators only. The freezer drawer stops short, springs back open or closes crooked. Check what is in it, whether the basket sits on its rails and whether ice has built up, then look at the slides, the rollers and the gasket.Open guide
- SymptomRefrigerator freezer frosting upA frost-free freezer should never need defrosting by hand. Frost near the door usually means a leaking gasket. Thick ice behind the rear panel, on the coil, means the defrost heater, the defrost thermostat or the defrost timer has failed.Open guide
- Refrigerator partDoor gasketThe door gasket is the soft magnetic seal around each door. When it tears, hardens or pulls away, warm air leaks in: you get condensation, frost near the door and a refrigerator that runs and runs.Open guide
- Refrigerator partDefrost heaterThe defrost heater sits under the freezer's evaporator coil and melts off the frost every so often. When it burns out, the coil ices over, airflow stops and the fresh-food section warms up first.Open guide
- Refrigerator partFrench-door alignmentFrench-door refrigerators only. Uneven doors are usually a cabinet that is not level or tilted forward. Level it with the front legs first, then fine-tune the door height at the bottom hinge as your manual describes, and check the center flap and the gaskets.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
