French doors uneven or not sealing
Good news: this is almost always an adjustment, not a broken part. Level the cabinet first, then set the door height at the hinge.
Check these first
Five-minute checks, no tools
Check it loaded
The doors are set up to carry food. An empty refrigerator can look uneven, so load it before you adjust anything.
Nothing in the way
Look for a bin, a tall bottle or a shelf edge that the door bins or the center flap hit as the doors close.
Center seal folded in
Open the left door and check the hinged flap on its inner edge. If it is sticking out, push it in by hand before you close the door.
Front a little higher
Put a level on top. The cabinet should be level side to side, with the front about 1/8 to 1/4 inch higher than the back. Open a door halfway: it should swing shut by itself.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Cabinet out of level
Both doors drift open, or one door sits low. Turn the front leveling legs in small, equal turns until the cabinet is level side to side and tilted slightly back.
Fix the door alignment20 min–1 hr$0 - 2DIY fix
Door height needs adjusting
The cabinet is level but the tops of the doors still do not line up. Many models have a height screw or nut on the lower hinge, reached with the freezer drawer open. Some have no adjustment, and leveling is all there is.
Fix the door alignment20 min–1 hr$0 - 3DIY fix
Bin or food in the way
A door bounces back or stops a little short. A crowded shelf, a tall item or a full door bin catches as it closes.
- 4DIY fix
Center seal flap folded the wrong way
The right door closes but the left one will not, or there is a gap where they meet. Push the hinged flap on the left door back in by hand before closing it.
- 5DIY fix
Worn door gasket
The doors line up but a sheet of paper closed in them slides out with no drag, or you see condensation along one edge. Clean the gasket first, then replace it if it is torn or flattened.
Fix the door gasket30 min–1 hr$50–$130
What's happening
What your refrigerator is doing
Two doors hang side by side on hinges at the outer edges of the cabinet, and they have to meet in the middle. If the cabinet leans, one door drops lower than the other and the gap between them opens up.
The doors are meant to close on their own. That only works when the front of the cabinet sits slightly higher than the back, so gravity swings them shut.
Where the doors meet, a hinged flap on the left door seals the gap. It has to be folded in before the left door closes, and a guide at the top of the cabinet steers it into place. If it is left sticking out, or a bin is in the way, the doors cannot close fully even when they are level.
Know your limits
When to call a pro
Stop and call a pro if
- The doors are out of line front to back, not just up and down.
- Your model has no height adjustment and leveling does not line the doors up.
- A hinge is cracked, loose in the cabinet or will not hold its setting.
FAQ
Common questions
How much should a French-door refrigerator tilt back?
Most makers want the front about 1/8 to 1/4 inch higher than the back, and level side to side. That is enough for the doors to swing shut by themselves.
Which way do I turn the hinge screw to raise a door?
It depends on the model, and makers describe it differently. Make a small turn, close the door and look, then carry on. Your owner's manual shows the tool and the direction.
My new refrigerator's doors look uneven. Is it faulty?
Probably not. The doors are set for the weight of food, so check again once the refrigerator is loaded. Then level the cabinet before you touch the hinges.
Related
Keep going
- SymptomFrench-door freezer drawer won't closeFrench-door and bottom-freezer refrigerators only. The freezer drawer stops short, springs back open or closes crooked. Check what is in it, whether the basket sits on its rails and whether ice has built up, then look at the slides, the rollers and the gasket.Open guide
- SymptomFreezer cold but fridge warmThe freezer still freezes but the fresh-food section warms up. All the cold comes from one coil in the freezer, so this usually means air is not moving: a stopped evaporator fan, an iced-over coil, or a blocked vent.Open guide
- SymptomRefrigerator freezer frosting upA frost-free freezer should never need defrosting by hand. Frost near the door usually means a leaking gasket. Thick ice behind the rear panel, on the coil, means the defrost heater, the defrost thermostat or the defrost timer has failed.Open guide
- Refrigerator partFrench-door alignmentFrench-door refrigerators only. Uneven doors are usually a cabinet that is not level or tilted forward. Level it with the front legs first, then fine-tune the door height at the bottom hinge as your manual describes, and check the center flap and the gaskets.Open guide
- Refrigerator partDoor gasketThe door gasket is the soft magnetic seal around each door. When it tears, hardens or pulls away, warm air leaks in: you get condensation, frost near the door and a refrigerator that runs and runs.Open guide
- Refrigerator partFreezer drawer slidesFrench-door refrigerators only. The freezer drawer rides out on two slides with rollers. A drawer that will not close or sits crooked usually has a basket off its rails, too much food, frost in the track, or a broken roller or bent slide. A sheet of ice behind the drawer is a defrost problem, not a slide problem.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy