Front-load washer door gasket: clean, check and replace
Most door-seal leaks and smells start with gunk in the folds. Clean it first. If it is torn, a new boot is a patient afternoon job.
- Difficulty
- Hard
- Time
- 1 hr–2 hr
- Typical part cost
- $40–$200Pro: $170–$600
- Tools
- 4See the list
Cleaning is easy. Replacing the boot means two spring clamps, often the front panel, and working rubber over a lip by hand. Allow time and patience.
What it does
What the door gasket does
The door boot is a thick rubber ring with folds in it. Its inner edge is clamped to the front of the tub and its outer edge to the cabinet opening, so the drum can move without water reaching the cabinet.
The door glass presses against it to seal the opening. On some washers, small drain holes in the bottom fold let water run back into the tub.
Why it fails
Detergent, lint and hair collect in the folds. Water wicks past the buildup and drips at the front, and the damp gunk grows mold that smells.
Coins, underwire and zippers can cut the rubber. A tear at the bottom leaks every wash.
A clamp that slipped or rusted can let the boot pull away from the tub or the cabinet.
Symptoms
Signs of a bad door gasket
Drips under the door
A puddle under the door after a wash. Often it is buildup on the seal, not a tear.
Full diagnosisMusty smell
A sour, moldy smell from the drum that comes back between washes. Look in the folds of the boot.
Tear or hole in the folds
Pull the folds open all the way around. A tear or a pinhole, often at the bottom, needs a new boot.
Full diagnosisBlack spots that will not wipe off
Mold that has grown into the rubber. Cleaning helps, but deep staining often means it is time for a new boot.
How to test it
Test the door gasket before you buy
- With the washer off, press the boot's folds open with both hands and wipe out soap, lint and anything trapped there.
- Check the drain holes at the bottom fold, if yours has them, and clear them.
- Work all the way around and look for tears, holes and spots where the rubber has pulled away from the tub or cabinet.
- Good
- Clean, whole rubber with both edges firmly clamped. Leave the door ajar between washes so it dries.
- Bad
- A tear, a hole or an edge that has come loose. Replace the boot, or refit the clamp if it only slipped.
Safety first
Before you touch anything
- 1
Unplug the washer
Pull the plug before you take off a clamp or a panel.
- 2
Turn the water off
Close both supply valves. Make sure the tub is drained.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Multi-bit screwdriverPhillips, flat, squarePries the clamp springs and removes the front panel screws.Typically $10–$25Shop this tool
- Torx driver bitsT15, T20, T25OptionalMany front-load panels use Torx screws.Typically $6–$15Shop this tool
- Needle-nose pliersStretches the outer spring clamp and the inner clamp off.Typically $8–$20Shop this tool
- Putty knifeStiff, 1-1/2 in.Helps tuck the boot lip back over the cabinet edge.Typically $5–$12Shop this tool
- Nitrile glovesFor cleaning a moldy boot.Typically $8–$15Shop this tool
Step by step
How to replace the door gasket
- 1
Unplug, water off, drum empty
Pull the plug, close both supply valves, and drain any water through the pump filter.
- 2
Remove the outer clamp
Find the spring on the outer wire clamp at the door opening. Pry it out or stretch it with pliers, then work the clamp off all the way around.
Peel the boot's outer lip off the cabinet edge and push it into the drum.
- 3
Take off the front panel if needed
On many front loaders the inner clamp is easier to reach with the front panel off. Remove the top panel, then the screws along the top and bottom of the front panel, unplug the door lock, and lift the panel off its hooks. On some models, heavy weights bolted to the front of the tub must come off too.
Some boots come out without removing the front panel. Check a parts diagram for your model.
- 4
Remove the inner clamp and the old boot
Note where any small hoses or a light connect to the boot, and take them off.
Release the inner clamp, which is usually a spring wire or a band with a screw, and pull the boot off the tub lip.
Tip. Mark the top of the old boot and the tub with tape so the new one goes on in the same position. Many boots have an arrow or tab that goes at the top.
- 5
Fit the new boot to the tub
Line up the marks and any drain holes at the bottom. Press the inner lip onto the tub lip all the way around.
Refit the inner clamp in its groove and reconnect any small hoses.
Buy the part
Door boot seal
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part listed for your washer's model number. Boots are shaped for one tub and one cabinet.
- A manufacturer-approved boot, with the same hose ports and drain holes as yours.
- 6
Panel back, outer lip, outer clamp
Refit the front panel, reconnect the door lock, and put the top back on.
Stretch the boot's outer lip over the cabinet edge, then fit the outer clamp, starting at the top and hooking the spring last.
- 7
Test for leaks
Turn the water on, plug in and run a short rinse with no clothes. Watch the floor under the door and check that the door closes and locks.
Buy the part
Get the right replacement
Buy the part
Door boot seal
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part listed for your washer's model number. Boots are shaped for one tub and one cabinet.
- A manufacturer-approved boot, with the same hose ports and drain holes as yours.
Know your limits
When to call a pro
Stop and call a pro if
- Water leaks from behind the boot, at the tub seal or around the drum shaft. That can point to the tub seal and bearings.
- The inner clamp cannot be reached without taking the tub apart on your model.
- The leak continues with a new boot and clean drain holes.
FAQ
Door boot seal questions
How do I stop my front loader smelling?
Wipe out the boot's folds after washing, leave the door ajar so it dries, and run the washer's tub clean cycle regularly. Washer makers' care guides recommend these steps.
Can I patch a torn door boot?
Patches rarely hold on rubber that flexes every spin. Replacing the boot is the reliable fix.
Is a puddle at the door always the boot?
No. Check the pump filter is screwed in, the fill hoses are dry, and the detergent dose is not causing suds. See washer leaking.
Related
Keep going
- SymptomWasher leaking waterA puddle under or behind the washer. Front leaks are usually the door seal or the pump filter. Back leaks are usually the fill hoses or the inlet valve. Find the spot first.Open guide
- Washer partDoor lock assemblyThe door lock latches a front-load door for the whole cycle and tells the control it is locked. When it fails the washer will not start, spin or unlock. Swapping it takes about 30 minutes.Open guide
- Washer partDrain pumpThe drain pump pushes the water out at the end of each wash and rinse. Clean the filter first. If it still will not drain, test the pump and swap it.Open guide
- Washer partFill hosesFill hoses carry water from the wall valves to the washer and are under pressure all the time. Several washer makers say to replace them every five years. Here is how to check and swap them.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
