Washer leaking water
Where the water shows up tells you most of the story. Front, back or underneath, each points to a short list of parts.
Check these first
Five-minute checks, no tools
Close the valves if it drips when off
If water appears with the washer idle, turn both supply valves off until you find the leak.
Pump filter fully closed
On a front loader, check the filter at the bottom front is screwed in all the way.
Wipe the door seal
Soap and lint on the boot let water wick out at the front. Wipe the folds and the edge.
Use less detergent
Too much soap, or the wrong kind, makes extra suds that can leak out. Use the type and amount of detergent your manual calls for.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Fill hoses
Water at the back, often drips at the fittings or a bulging hose. Worse when the valves are open.
Fix the fill hoses10–25 min$10–$40 - 2DIY fix
Door boot seal (front load)
Water under the door during the wash, from buildup on the seal or a tear in it.
Fix the door gasket1 hr–2 hr$40–$200 - 3DIY fix
Drain pump or pump filter
Water at the front bottom, often during drain. A loose filter, a cracked housing or a loose hose clamp.
Fix the drain pump30 min–1.3 hr$20–$100 - 4DIY fix
Water inlet valve
Drips at the back where the hoses connect, or water creeping into the tub when the washer is off.
Fix the inlet valve30 min–1 hr$15–$100 - 5DIY fix
Drain hose or standpipe
Water on the floor only during drain. A loose hose end, a crack, or a standpipe that overflows.
- 6Call a pro
Tub seal or tub
Water from the middle of the base with every part above checked dry. That is a bigger job for a pro.
What's happening
What your washer is doing
Fill hoses and the inlet valve hold full house pressure, even with the washer off. A leak there drips all the time, or only when the valves are open.
During a cycle, water can escape at the front around the door boot, at a pump filter that is not screwed in fully, or through excess suds.
Water that appears only during drain points to the drain hose, the pump or the standpipe. Water from under the middle of the washer can mean a pump, an internal hose or the tub itself.
Know your limits
When to call a pro
Stop and call a pro if
- Water is near the outlet, the cord or the wiring. Unplug at the breaker if the plug is wet.
- The leak comes from the tub or the drum shaft area. That usually means a tub seal, often with worn bearings.
- A wall valve or the standpipe is leaking. Call a plumber.
FAQ
Common questions
How do I find where my washer is leaking?
Dry the floor, put paper towels around the base, and run a short cycle while you watch. Note when the water appears: idle, filling, washing or draining.
Why does my front loader leak from the door?
Most often buildup in the door seal, a sock caught in it, or too much detergent. A torn seal is next. See the door gasket guide.
Is a leaking washer dangerous?
Water and electricity are a bad mix. If water is near the outlet or cord, switch off the breaker before you touch the plug.
Related
Keep going
- SymptomWasher won't drainThe cycle stops with water in the tub, or the clothes come out soaking. A clogged pump filter, a kinked drain hose or a jammed pump causes most of it.Open guide
- SymptomWasher won't fill with waterThe tub stays dry, fills very slowly, or only gets hot or cold water. Check the supply valves, the hoses and the inlet screens, then test the inlet valve.Open guide
- Washer partFill hosesFill hoses carry water from the wall valves to the washer and are under pressure all the time. Several washer makers say to replace them every five years. Here is how to check and swap them.Open guide
- Washer partDoor boot sealThe rubber boot seals the front-load door to the tub. Soap and lint in its folds cause smells and small leaks, and a tear causes real ones. Clean it, check it, and replace it if it is torn.Open guide
- Washer partDrain pumpThe drain pump pushes the water out at the end of each wash and rinse. Clean the filter first. If it still will not drain, test the pump and swap it.Open guide
- Washer partWater inlet valveThe inlet valve lets hot and cold water into the washer. Clogged screens slow it down, and a burned-out coil stops one side. Clean, test and replace it from the back of the washer.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
