Washer won't fill, or fills slowly
Start at the wall. Closed valves, kinked hoses and clogged inlet screens cause most no-fill problems, and none of them needs a new part.
Check these first
Five-minute checks, no tools
Supply valves open
Both valves behind the washer should be turned fully open. Someone may have closed them.
Hoses not kinked
Pull the washer out and straighten any kink or crushed spot in the fill hoses.
Clean the inlet screens
Unplug, close the valves, unscrew the hoses from the washer and rinse the small screens in the valve inlets.
Door locks (front load)
If the door lock light does not come on, the fill will not start. See door won't lock.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Clogged inlet screens
Grit and scale block the screens. Slow fill, or only one side filling.
Fix the inlet valve30 min–1 hr$15–$100 - 2DIY fix
Water supply off or kinked hose
Closed wall valves or a crushed fill hose. No water reaches the washer.
- 3DIY fix
Failed inlet valve coil
Strong flow at the hoses but no fill on one side. The coil tests open.
Fix the inlet valve30 min–1 hr$15–$100 - 4DIY fix
Door lock (front load)
The washer never confirms the door is locked, so it never starts to fill.
Fix the door lock20–40 min$20–$130 - 5DIY fix
Control board or water level sensing
The valve tests good and gets no power, or the washer thinks it is already full.
Fix the control board20–45 min$100–$300
What's happening
What your washer is doing
When a fill starts, the control powers one or both coils on the water inlet valve. Water flows from the wall valves, through the fill hoses and the inlet screens, and into the tub.
If the screens are clogged, the fill slows to a trickle. If a coil has burned out, that side, hot or cold, never opens.
On front loaders, the door has to lock before the fill starts, so a door lock problem can look like a fill problem.
Know your limits
When to call a pro
Stop and call a pro if
- Low flow at every faucet in the house, or a wall valve that will not open. That is plumbing.
- A new valve, clean screens and strong flow, and it still will not fill.
- It fills with the washer turned off. Close the valves until it is fixed.
FAQ
Common questions
Why is my washer filling so slowly?
Most often clogged inlet screens. Clean them, and check that the wall valves are fully open. See the water inlet valve guide.
Is it normal for an efficient washer to use little water?
Yes. Efficient washers can use about 30 percent less water than standard ones, so a shallow fill can be normal. A tub that stays completely dry is not.
Can old fill hoses cause slow filling?
A kinked or collapsed hose can. Hoses older than about five years are due for replacement anyway.
Related
Keep going
- SymptomWasher won't startNothing happens when you press Start, or it lights up but will not begin. Power, the child lock or delay start, and the lid switch or door lock cause most of it.Open guide
- SymptomWasher leaking waterA puddle under or behind the washer. Front leaks are usually the door seal or the pump filter. Back leaks are usually the fill hoses or the inlet valve. Find the spot first.Open guide
- Washer partWater inlet valveThe inlet valve lets hot and cold water into the washer. Clogged screens slow it down, and a burned-out coil stops one side. Clean, test and replace it from the back of the washer.Open guide
- Washer partFill hosesFill hoses carry water from the wall valves to the washer and are under pressure all the time. Several washer makers say to replace them every five years. Here is how to check and swap them.Open guide
- Washer partDoor lock assemblyThe door lock latches a front-load door for the whole cycle and tells the control it is locked. When it fails the washer will not start, spin or unlock. Swapping it takes about 30 minutes.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
