Washer control board replacement
The control board gets blamed a lot. Check the cheaper parts first. If it really is the board, the swap is plugs and screws.
- Difficulty
- Easy
- Time
- 20–45 min
- Typical part cost
- $100–$300Pro: $200–$550
- Tools
- 2See the list
Plugs and screws. The hard part is being sure the board is really the problem.
What it does
What the control board does
The main control board times the cycle, reads the lid or door, the water level and the motor speed, and switches the valve, the pump, the lock and the motor on and off.
Some front loaders also have a separate motor control board near the motor that takes orders from the main board and drives the motor.
Why it fails
Power surges, heat and moisture can damage relays and components on the board.
A board can also be blamed for a fault that is really a bad part it is trying to power, like a shorted pump or valve.
Symptoms
Signs of a bad control board
Dead display
Nothing lights up, even though the outlet works and the breaker is on.
Full diagnosisRandom stops and errors
It stops at different points in the cycle, or shows codes that do not match any one part.
One part never gets power
The pump, valve or motor tests good but never runs. Its signal from the board may be missing.
Full diagnosis
How to test it
Test the control board before you buy
- Plug a lamp into the washer's outlet to confirm it works, and check the breaker.
- Unplug the washer for about five minutes to reset it, then try again.
- Read any error code and look it up in your manual. Many codes point to a part, not the board.
- Test the parts the code points to, like the drain pump, inlet valve or door lock.
- Good
- Often one of those turns out to be the problem. Fix that part.
- Bad
- The outlet works, the parts test good, and the board still does not power them. The board is the likely cause.
- Unplug the washer and open the console or the panel over the board.
- Look for burn marks, melted plugs, swollen parts and corrosion.
- Good
- A clean board does not prove it is good, but it points you back to the parts and the wiring.
- Bad
- Burn marks or melted plugs. Replace the board, and check the part on that plug, since it may have caused the damage.
Safety first
Before you touch anything
- 1
Unplug the washer
Pull the plug and wait a few minutes before you touch the board.
- 2
Handle it by the edges
Static can damage a board. Touch bare metal on the cabinet first, keep the new board in its bag until you fit it, and hold it only by its edges.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Multi-bit screwdriverPhillips, flat, squareRemoves the console and board cover screws.Typically $10–$25Shop this tool
- Nut driver1/4 in. hexOptionalMany consoles use 1/4 in. hex screws.Typically $6–$15Shop this tool
- Painter's tape and markerLabel every plug before you take it off the old board.Typically $5–$12Shop this tool
Step by step
How to replace the control board
- 1
Unplug the washer
Pull the plug. Close the water valves.
- 2
Reach the board
Most main boards sit behind the console or under the top panel. Remove the screws and lift or tilt it open.
A separate motor control board, if your washer has one, sits low near the motor behind a lower or rear panel.
- 3
Label and unplug
Photograph the board, then put a strip of tape with a letter on each plug.
Release each tab and pull the plugs off by their bodies, not the wires.
- 4
Swap the board
Remove the screws or release the clips, and lift the old board out of its housing.
Fit the new board the same way. Do not touch the components on its face.
Buy the part
Control board
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part number on the old board's sticker, plus your washer's model number. Boards are model specific.
- Whether you need the main board, the user interface board or the motor control board.
- 5
Reconnect and close up
Plug everything back in to match your labels and photo, reconnect any green ground wire, then refit the console.
- 6
Test a full cycle
Open the water, plug in and run a short full cycle. Some new boards need a setup step from the instructions that come with them.
Buy the part
Get the right replacement
Buy the part
Control board
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The part number on the old board's sticker, plus your washer's model number. Boards are model specific.
- Whether you need the main board, the user interface board or the motor control board.
Know your limits
When to call a pro
Stop and call a pro if
- You are not sure the board is the problem. A pro can test its outputs live, which is not a safe DIY test.
- The new board shows the same fault. The wiring harness or another part is the cause.
- The board is burned. Have the wiring checked too.
FAQ
Control board questions
How do I know it is the board?
Usually by elimination. When every part the board powers tests good and the outlet works, the board is the likely cause. Live voltage tests on a board are best left to a pro.
Is a used or rebuilt board OK?
It can be, if the part number matches exactly. Check the seller's return rules first. Some sellers will not take back an electrical part once it has been installed.
Will a power reset fix it?
Sometimes. Washer makers suggest unplugging for about five minutes to reset the control. If the same fault comes back, look for the cause.
Related
Keep going
- SymptomWasher won't startNothing happens when you press Start, or it lights up but will not begin. Power, the child lock or delay start, and the lid switch or door lock cause most of it.Open guide
- SymptomWasher won't spinThe clothes come out soaking, or the washer agitates but never spins. Check drainage, the lid switch or door lock, and the load first, then the belt or motor coupler.Open guide
- Washer partDrain pumpThe drain pump pushes the water out at the end of each wash and rinse. Clean the filter first. If it still will not drain, test the pump and swap it.Open guide
- Washer partDoor lock assemblyThe door lock latches a front-load door for the whole cycle and tells the control it is locked. When it fails the washer will not start, spin or unlock. Swapping it takes about 30 minutes.Open guide
- Washer partDrive motorThe drive motor turns the agitator or drum through a coupler, a belt, or directly. It fails less often than the parts around it. Check the error code and the cheaper parts first, then swap it.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
