Washer won't spin
A washer that will not spin is usually protecting itself. Either the water is not out, the lid or door is not confirmed, or something in the drive has let go.
Check these first
Five-minute checks, no tools
Is the water out?
If water is left in the tub, fix the drain first. See washer won't drain.
Lid or door fully shut
Close it firmly. Check nothing is caught in the door seal and the lid strike is not broken.
Rebalance the load
A single heavy item cannot balance. Spread the load out, or add a couple of towels, and try a rinse and spin.
Reset the power
Unplug the washer for about five minutes, plug it back in and try a spin-only cycle.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Water not draining
The washer will not spin with water in the tub. A clogged filter or a bad pump stops the spin too.
Fix the drain pump30 min–1.3 hr$20–$100 - 2DIY fix
Lid switch (top load)
The washer fills and agitates, then skips the spin, because it never sees the lid as shut.
Fix the lid switch20–45 min$10–$60 - 3DIY fix
Door lock (front load)
The door will not lock or report locked, so the drum will not spin.
Fix the door lock20–40 min$20–$130 - 4DIY fix
Motor coupler (direct-drive top load)
Fills and drains, the motor runs, but nothing agitates or spins.
Fix the motor coupler30 min–1 hr$5–$30 - 5DIY fix
Drive belt
The motor runs but the drum does not turn on a belt-drive washer.
Fix the belt20–45 min$5–$30 - 6DIY fix
Drive motor
Silent or humming with nothing turning, usually with a motor error code. Rule out the cheaper parts first.
Fix the motor1 hr–2 hr$100–$350 - 7DIY fix
Control board
Every part tests good and still does not get power.
Fix the control board20–45 min$100–$300
What's happening
What your washer is doing
Before it spins, a washer needs three things: the tub drained, the lid or door confirmed shut and locked, and a load balanced enough to spin safely.
If any of those fail, most washers simply skip or stop the spin. Some flash a lid or door code, and some pause again and again trying to rebalance.
If all three are fine and the motor runs while the basket stays still, the drive has a problem: a broken motor coupler on direct-drive top loaders, or a slipped belt on belt-drive washers.
Know your limits
When to call a pro
Stop and call a pro if
- The basket will not turn by hand, or grinds, with the washer unplugged. The bearings or the transmission may be bad.
- You smell burning or see smoke. Unplug it and leave it unplugged.
- The drain, the lid or door, the belt and the coupler all check out.
FAQ
Common questions
Why does my washer agitate but not spin?
On a top loader, the lid switch is the first suspect, especially if the lid strike is fine. Next is a drain problem, then the drive.
Can I bypass the lid switch to test it?
No. Test the switch with a meter instead. Bypassing it lets the basket spin while your hands can reach in.
My front loader keeps pausing and will not spin. Why?
It is probably trying to balance. Spread the load out and try again. If it does the same with a normal load, look at the shock absorbers and the drain.
Related
Keep going
- SymptomWasher won't drainThe cycle stops with water in the tub, or the clothes come out soaking. A clogged pump filter, a kinked drain hose or a jammed pump causes most of it.Open guide
- SymptomWasher shaking, banging or walkingThe washer bangs, shakes or walks during spin. Rebalance the load and level the washer first. If it still bangs, the suspension rods or shock absorbers are worn.Open guide
- SymptomWasher door won't lock or unlockThe lock light blinks and the cycle will not start, or the door stays locked after the cycle. Check the door closes cleanly, drain any water, then test or replace the door lock.Open guide
- Washer partLid switch or lid lockThe lid switch tells a top loader its lid is shut, and on many newer washers it also locks the lid. When it fails the washer will not spin or start. Test it and swap it in under an hour.Open guide
- Washer partDoor lock assemblyThe door lock latches a front-load door for the whole cycle and tells the control it is locked. When it fails the washer will not start, spin or unlock. Swapping it takes about 30 minutes.Open guide
- Washer partDrain pumpThe drain pump pushes the water out at the end of each wash and rinse. Clean the filter first. If it still will not drain, test the pump and swap it.Open guide
- Washer partMotor couplerOn direct-drive top loaders, the motor coupler links the motor to the transmission and breaks on purpose to protect the motor. When it fails, the washer fills and drains but will not agitate or spin.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
