Washer drive belt replacement
Motor running, drum not turning? On a belt-drive front loader, a slipped or broken belt is a common and quick fix from the back panel.
- Difficulty
- Easy
- Time
- 20–45 min
- Typical part cost
- $5–$30Pro: $90–$200
- Tools
- 2See the list
Remove the back panel and roll a belt on. Getting the last bit onto the pulley takes a firm hand.
What it does
What the belt does
Many front loaders, and some top loaders, use a belt. A small pulley on the motor drives a large pulley on the back of the drum through a ribbed belt.
Not every washer has one. Direct-drive washers bolt the motor straight to the drum shaft, and older direct-drive top loaders use a motor coupler instead.
Why it fails
Belts stretch, crack and glaze with age, then slip or squeal.
A belt can come off its pulleys completely, so the motor spins with nothing to turn.
A belt that keeps coming off can mean a loose motor, a damaged pulley or a worn drum support.
Symptoms
Signs of a bad belt
Motor runs, drum does not
You hear the motor, but the drum does not turn, or turns only when you push it.
Full diagnosisSqueal at start or spin
A worn, glazed belt slips and squeals as the drum speeds up.
Drum spins freely by hand
With the washer off, the drum turns with almost no resistance, and you do not hear the motor turning with it.
How to test it
Test the belt before you buy
- Unplug the washer and pull it out. Remove the screws around the rear panel and take it off.
- Check that the belt is on both pulleys and sitting in the grooves.
- Look along the whole belt for cracks, missing ribs, fraying and a shiny, glazed surface.
- Good
- A snug belt with clean, sharp ribs, sitting on both pulleys.
- Bad
- Broken, off the pulleys, cracked or glazed. Replace it.
- With the belt off, turn the big drum pulley by hand. Listen and feel.
- Good
- It turns smoothly and quietly. Fit the new belt.
- Bad
- It grinds, rumbles or will not turn freely. That points to the drum bearings or the rear drum support. Call a pro.
Safety first
Before you touch anything
- 1
Unplug the washer
Pull the plug before you remove the rear panel. The motor and its wiring sit right behind it.
Tools you'll need
Grab these first
Tool and part links are affiliate links. We may earn a commission at no extra cost to you, and it never changes what we tell you to check first. How this works
- Multi-bit screwdriverPhillips, flat, squareRemoves the rear panel screws.Typically $10–$25Shop this tool
- Nut driver1/4 in. hexOptionalSome rear panels use hex-head screws.Typically $6–$15Shop this tool
- Work glovesProtects your fingers when you roll the belt on.Typically $8–$20Shop this tool
Step by step
How to replace the belt
- 1
Unplug and pull it out
Pull the plug and close both supply valves. Pull the washer far enough out to work behind it.
- 2
Take off the rear panel
Remove the screws around the edge of the rear panel. They may be different lengths, so note where each goes.
- 3
Remove the old belt
Photograph how the belt runs. Then pull the belt off the edge of the big drum pulley while you turn the pulley by hand. It walks off.
- 4
Fit the new belt
Loop the new belt around the small motor pulley first, ribs in the grooves. Then start it on the big pulley at the top, and turn the pulley while you guide the belt on.
Check that the ribs sit in the grooves on both pulleys.
Buy the part
Drive belt
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The belt number printed on the old belt, or the part listed for your washer's model number.
- The same rib count and length.
- 5
Close up and test
Refit the rear panel. Plug in, open the water, and run a rinse and spin. The drum should turn and spin quietly.
Buy the part
Get the right replacement
Buy the part
Drive belt
Opens Amazon in a new tab. Where’s my model number?
What to look for
- The belt number printed on the old belt, or the part listed for your washer's model number.
- The same rib count and length.
Know your limits
When to call a pro
Stop and call a pro if
- The drum grinds or will not turn freely by hand with the belt off.
- A new belt keeps coming off. The motor mount, the pulley or the rear drum support may be damaged.
- The big drum pulley is cracked or wobbles on its shaft.
FAQ
Drive belt questions
Does my washer have a belt?
Take off the rear panel and look. If you see a big pulley on the back of the drum with a belt to the motor, yes. If you see a large round motor on the back of the tub with no belt, it is direct drive.
Why does my new belt keep falling off?
The belt is the symptom. Check that the motor is tight on its mount, the pulley is not wobbling, and the drum turns smoothly. A pro should look at worn drum supports.
Can I use a generic belt?
Only if it matches the rib count and length exactly. The part number on the old belt is the easiest way to match it.
Related
Keep going
- SymptomWasher won't spinThe clothes come out soaking, or the washer agitates but never spins. Check drainage, the lid switch or door lock, and the load first, then the belt or motor coupler.Open guide
- Washer partDrive motorThe drive motor turns the agitator or drum through a coupler, a belt, or directly. It fails less often than the parts around it. Check the error code and the cheaper parts first, then swap it.Open guide
- Washer partShock absorbersShock absorbers connect a front loader's tub to the base and soak up its movement on spin. When they wear out, the tub bangs and the washer walks. Level the washer first, then replace them as a set.Open guide
- Washer partMotor couplerOn direct-drive top loaders, the motor coupler links the motor to the transmission and breaks on purpose to protect the motor. When it fails, the washer fills and drains but will not agitate or spin.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
