Washer shaking, banging or walking on spin
A washer that dances across the floor is scary, but the usual causes are simple: the load, the leveling, or the parts that hold the tub steady.
Check these first
Five-minute checks, no tools
Rebalance the load
Pause, spread the clothes out, and add a towel or two to balance a single heavy item. Then test with an empty rinse and spin.
Level it
Put a level on top, front to back and side to side. Adjust the legs until it sits level and does not rock, then lock the leg nuts. On a newly installed front loader, check that the shipping bolts at the back were removed.
Check the floor
A floor that flexes or bounces makes any washer shake more. Washer makers call for a solid floor and say to avoid carpet and weak platforms. A bouncy floor is a job for a contractor.
Likely causes
Ranked by how often they are the problem
- 1DIY fix
Unbalanced load
One heavy item or a load bunched to one side. It stops when you redistribute it.
- 2DIY fix
Washer not level
A short or loose leg lets the washer rock, and the spin turns that into walking.
- 3DIY fix
Worn suspension rods (top load)
The tub bounces and bangs the cabinet even when empty and level.
Fix the suspension rods45 min–2 hr$25–$80 - 4DIY fix
Worn shock absorbers (front load)
The tub swings freely and slams the cabinet as the spin speeds up.
Fix the shocks30 min–1.3 hr$30–$150 - 5Call a pro
Drum bearings or tub supports
A roar or grind on spin as well as shaking. That is a bigger repair for a pro.
What's happening
What your washer is doing
The tub floats inside the cabinet. On a top loader it hangs from suspension rods; on a front loader it rests on springs and shock absorbers. They let it move, and damp that movement, so a heavy spin does not shake the cabinet.
If the load bunches on one side, the tub swings hard as it spins up. A washer that is not level, or rocks on a leg, turns that swing into walking.
Worn rods or shocks stop damping, so even a normal load bangs the tub against the cabinet.
Know your limits
When to call a pro
Stop and call a pro if
- A roar, a grind or a scraping sound on spin. The bearings or the drum support may be failing.
- The tub is visibly loose, sagging or cracked.
- New rods or shocks and a level washer still bang hard.
FAQ
Common questions
Why does my washer only shake with towels or bedding?
Big, heavy items bunch up and throw the load off balance. Wash them with a few similar items so the weight spreads out.
How do I stop my washer walking?
Level it so it sits firmly on all four legs, lock the leg nuts, and balance the load. If it still walks, check the shock absorbers or suspension rods.
Can a clogged pump make it shake?
Yes. Water left in the tub makes the load heavy and lopsided. Clean the pump filter if it drains slowly.
Related
Keep going
- SymptomWasher won't spinThe clothes come out soaking, or the washer agitates but never spins. Check drainage, the lid switch or door lock, and the load first, then the belt or motor coupler.Open guide
- SymptomWasher won't drainThe cycle stops with water in the tub, or the clothes come out soaking. A clogged pump filter, a kinked drain hose or a jammed pump causes most of it.Open guide
- Washer partSuspension rodsFour suspension rods hang a top loader's tub from the cabinet corners and damp it on spin. Worn rods let it bang and walk. Replace all four as a set.Open guide
- Washer partShock absorbersShock absorbers connect a front loader's tub to the base and soak up its movement on spin. When they wear out, the tub bangs and the washer walks. Level the washer first, then replace them as a set.Open guide
- Washer partDrain pumpThe drain pump pushes the water out at the end of each wash and rinse. Clean the filter first. If it still will not drain, test the pump and swap it.Open guide
Get the next fix before it breaks
A short email when the seasons turn: filters to change, detector batteries to check, and new repair guides. No spam, unsubscribe any time.
We send it with Kit. Privacy
